# SPDX-License-Identifier: GPL-2.0-or-later

# script for stm32l5x family

#
# stm32l5 devices support both JTAG and SWD transports.
#
source [find target/swj-dp.tcl]
source [find mem_helper.tcl]

if { [info exists CHIPNAME] } {
	set _CHIPNAME $CHIPNAME
} else {
	set _CHIPNAME stm32l5x
}

set _ENDIAN little

# Work-area is a space in RAM used for flash programming
# By default use 64kB
if { [info exists WORKAREASIZE] } {
	set _WORKAREASIZE $WORKAREASIZE
} else {
	set _WORKAREASIZE 0x10000
}

#jtag scan chain
if { [info exists CPUTAPID] } {
	set _CPUTAPID $CPUTAPID
} else {
	if { [using_jtag] } {
		# See STM Document RM0438
		# RM0438 Rev5, Section 52.2.8 JTAG debug port - Table 425. JTAG-DP data registers
		# Corresponds to Cortex®-M33 JTAG debug port ID code
		set _CPUTAPID 0x0ba04477
	} {
		# SWD IDCODE (single drop, arm)
		set _CPUTAPID 0x0be12477
	}
}

swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu

if {[using_jtag]} {
	jtag newtap $_CHIPNAME bs -irlen 5
}

set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap

# use non-secure RAM by default
$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0

# declare non-secure flash
flash bank $_CHIPNAME.flash_ns stm32l4x 0x08000000 0 0 0 $_TARGETNAME
flash bank $_CHIPNAME.otp      stm32l4x 0x0BFA0000 0 0 0 $_TARGETNAME

# Common knowledges tells JTAG speed should be <= F_CPU/6.
# F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
# the safe side.
#
# Note that there is a pretty wide band where things are
# more or less stable, see http://openocd.zylin.com/#/c/3366/
adapter speed 500

adapter srst delay 100
if {[using_jtag]} {
	jtag_ntrst_delay 100
}

reset_config srst_nogate

if {![using_hla]} {
	# if srst is not fitted use SYSRESETREQ to
	# perform a soft reset
	cortex_m reset_config sysresetreq
}

proc clock_config_110_mhz {} {
	# MCU clock is MSI (4MHz) after reset, set MCU freq at 110 MHz with PLL
	# RCC_APB1ENR1 = PWREN
	mww 0x40021058 0x10000000
	# delay for register clock enable (read back reg)
	mrw 0x40021058
	# PWR_CR1 : VOS Range 0
	mww 0x40007000 0
	# while (PWR_SR2 & VOSF)
	while {([mrw 0x40007014] & 0x0400)} {}
	# FLASH_ACR : 5 WS for 110 MHz HCLK
	mww 0x40022000 0x00000005
	# RCC_PLLCFGR = PLLP=PLLQ=0, PLLR=00=2, PLLREN=1, PLLN=55, PLLM=0000=1, PLLSRC=MSI 4MHz
	# fVCO = 4 x 55 /1 = 220
	# SYSCLOCK = fVCO/PLLR = 220/2 = 110 MHz
	mww 0x4002100C 0x01003711
	# RCC_CR |= PLLON
	mmw 0x40021000 0x01000000 0
	# while !(RCC_CR & PLLRDY)
	while {!([mrw 0x40021000] & 0x02000000)} {}
	# RCC_CFGR |= SW_PLL
	mmw 0x40021008 0x00000003 0
	# while ((RCC_CFGR & SWS) != PLL)
	while {([mrw 0x40021008] & 0x0C) != 0x0C} {}
}

$_TARGETNAME configure -event reset-init {
	clock_config_110_mhz
	# Boost JTAG frequency
	adapter speed 4000
}

$_TARGETNAME configure -event reset-start {
	# Reset clock is MSI (4 MHz)
	adapter speed 480
}

$_TARGETNAME configure -event examine-end {
	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP
	mmw 0xE0044004 0x00000006 0

	# Stop watchdog counters during halt
	# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
	mmw 0xE0044008 0x00001800 0
}

$_TARGETNAME configure -event trace-config {
	# Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
	# change this value accordingly to configure trace pins
	# assignment
	mmw 0xE0044004 0x00000020 0
}