- stm32x flash driver: add support for low density devices

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 98ad644f77ac328ea3da66db40d33e9ea42d71b9..b436ab721e76f129bd4cfad90a0dadedeaa3a8bc 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -265,10 +265,6 @@ OpenOCD command line using the @option{-c} command line switch.
 @item @b{telnet_port} <@var{number}>
 @cindex telnet_port
 @*Port on which to listen for incoming telnet connections 
-@item @b{telnet_async} <@var{enable/disable}>
-@cindex telnet_async
-@*Enable/disable asynchronous messages. Default off. Slows down debugging
-if enabled and telnet session is open while stepping.
 @item @b{tcl_port} <@var{number}>
 @cindex tcl_port
 @*Port on which to listen for incoming TCL syntax. This port is intended as
@@ -576,11 +572,13 @@ Currently, there are no options available for the ep93xx interface.
 @item @b{cortex_m3}
 @item @b{feroceon}
 @item @b{xscale}
+@item @b{arm11}
 @item @b{mips_m4k}
 @end itemize
 
 If you want to use a target board that is not on this list, see Adding a new
-target board
+target board.
+The @option{target types} command can be used to get the list of targets supported from within openocd.
 
 Endianess may be @option{little} or @option{big}.
 
@@ -638,6 +636,16 @@ be detected and the normal reset behaviour used.
 Supported variants are @option{ixp42x}, @option{ixp45x}, @option{ixp46x},
 @option{pxa250}, @option{pxa255}, @option{pxa26x}.
 
+@subsection arm11 options
+@cindex arm11 options
+
+@subsection mips_m4k options
+@cindex mips_m4k options
+Use variant @option{ejtag_srst} when debugging targets that
+do not provide a functional SRST line on the EJTAG connector.
+This causes openocd to instead use an EJTAG software reset command to reset the processor.
+You still need to enable @option{srst} on the reset configuration command to enable openocd hardware reset functionality.
+
 @section Flash configuration
 @cindex Flash configuration
 
@@ -1751,6 +1759,15 @@ is a ARM920T (2x16kByte cache) or ARM922T (2x8kByte cache).
 @*Translate a virtual address to a physical address. 
 @end itemize
 
+@subsection CORTEX_M3 specific commands
+@cindex CORTEX_M3 specific commands
+
+@itemize @bullet
+@item @b{cortex_m3 maskisr} <@var{on}|@var{off}>
+@cindex cortex_m3 maskisr
+@*Enable masking (disabling) interrupts during target step/resume.
+@end itemize
+
 @page
 @section Debug commands
 @cindex Debug commands
@@ -2093,6 +2110,22 @@ halt
 @chapter FAQ
 @cindex faq
 @enumerate
+@item Why does not backslashes in paths under Windows doesn't work?
+
+OpenOCD uses Tcl and a backslash is an escape char. Use @{ and @}
+around Windows filenames. 
+
+@smallexample
+> echo \a
+
+> echo @{\a@}
+\a
+> echo "\a"
+
+>
+@end smallexample
+To 
+
 @item OpenOCD complains about a missing cygwin1.dll.
 
 Make sure you have Cygwin installed, or at least a version of OpenOCD that