target: Use target_addr_t for algorithm addresses.

[openocd.git] / tcl / target / stm32l4x.cfg

diff --git a/tcl/target/stm32l4x.cfg b/tcl/target/stm32l4x.cfg
index 9cad7c492c6b2ea29a905b7dfbd48f4d439324a2..5899791938edf2484c29d2f9cdc3d6327b9bc923 100644 (file)
--- a/tcl/target/stm32l4x.cfg
+++ b/tcl/target/stm32l4x.cfg
@@ -36,18 +36,36 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 if {[using_jtag]} {
    jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
-set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_CHIPNAME.otp   stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
+
+if { [info exists QUADSPI] && $QUADSPI } {
+   set a [llength [flash list]]
+   set _QSPINAME $_CHIPNAME.qspi
+   flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
+} else {
+   if { [info exists OCTOSPI1] && $OCTOSPI1 } {
+      set a [llength [flash list]]
+      set _OCTOSPINAME1 $_CHIPNAME.octospi1
+      flash bank $_OCTOSPINAME1 stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
+   }
+   if { [info exists OCTOSPI2] && $OCTOSPI2 } {
+      set b [llength [flash list]]
+      set _OCTOSPINAME2 $_CHIPNAME.octospi2
+      flash bank $_OCTOSPINAME2 stmqspi 0x70000000 0 0 0 $_TARGETNAME 0xA0001400
+   }
+}
 
 # Common knowledges tells JTAG speed should be <= F_CPU/6.
 # F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
@@ -55,9 +73,9 @@ flash bank $_FLASHNAME stm32l4x 0 0 0 0 $_TARGETNAME
 #
 # Note that there is a pretty wide band where things are
 # more or less stable, see http://openocd.zylin.com/#/c/3366/
-adapter_khz 500
+adapter speed 500
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 if {[using_jtag]} {
  jtag_ntrst_delay 100
 }
@@ -75,14 +93,14 @@ $_TARGETNAME configure -event reset-init {
        # Use MSI 24 MHz clock, compliant even with VOS == 2.
        # 3 WS compliant with VOS == 2 and 24 MHz.
        mww 0x40022000 0x00000103   ;# FLASH_ACR = PRFTBE | 3(Latency)
-       mww 0x40021000 0x00000099   ;# RCC_CR = MSI_ON | MSIRGSEL| MSI Range 10
+       mww 0x40021000 0x00000099   ;# RCC_CR = MSI_ON | MSIRGSEL | MSI Range 9
        # Boost JTAG frequency
-       adapter_khz 4000
+       adapter speed 4000
 }
 
 $_TARGETNAME configure -event reset-start {
        # Reset clock is MSI (4 MHz)
-       adapter_khz 500
+       adapter speed 500
 }
 
 $_TARGETNAME configure -event examine-end {