X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=doc%2Fopenocd.texi;h=c5975c9d3fc8f381f7777b83c345ad13e91d89a5;hb=03b190522330093db55e2268392ae9f291f6aa0e;hp=7cba65dd0ca1d1bfd2f40ba947a222aa73f7cef6;hpb=592d0d514d6602ae9c91cda7e4271c28222a25f6;p=openocd.git

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 7cba65dd0c..c5975c9d3f 100644
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -288,12 +288,11 @@ communication between developers:
 
 @uref{https://lists.sourceforge.net/mailman/listinfo/openocd-devel}
 
-@section OpenOCD Bug Database
+@section OpenOCD Bug Tracker
 
-During the 0.4.x release cycle the OpenOCD project team began
-using Trac for its bug database:
+The OpenOCD Bug Tracker is hosted on SourceForge:
 
-@uref{https://sourceforge.net/apps/trac/openocd}
+@uref{https://sourceforge.net/p/openocd/tickets/}
 
 
 @node Debug Adapter Hardware
@@ -2585,6 +2584,11 @@ cmsis_dap_vid_pid 0xc251 0xf001 0x0d28 0x0204
 @end example
 @end deffn
 
+@deffn {Config Command} {cmsis_dap_serial} [serial]
+Specifies the @var{serial} of the CMSIS-DAP device to use.
+If not specified, serial numbers are not considered.
+@end deffn
+
 @deffn {Command} {cmsis-dap info}
 Display various device information, like hardware version, firmware version, current bus status.
 @end deffn
@@ -3100,6 +3104,11 @@ Specifies the adapter layout to use.
 The vendor ID and product ID of the device.
 @end deffn
 
+@deffn {Command} {hla_command} command
+Execute a custom adapter-specific command. The @var{command} string is
+passed as is to the underlying adapter layout handler.
+@end deffn
+
 @deffn {Config Command} {trace} source_clock_hz [output_file_path]
 Enable SWO tracing (if supported). The source clock rate for the
 trace port must be specified, this is typically the CPU clock rate. If
@@ -4834,6 +4843,7 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 
 @deffn Command {flash write_image} [erase] [unlock] filename [offset] [type]
 Write the image @file{filename} to the current target's flash bank(s).
+Only loadable sections from the image are written.
 A relocation @var{offset} may be specified, in which case it is added
 to the base address for each section in the image.
 The file [@var{type}] can be specified
@@ -5045,6 +5055,34 @@ at91samd set-security enable
 @end example
 @end deffn
 
+@deffn Command {at91samd eeprom}
+Shows or sets the EEPROM emulation size configuration, stored in the User Row
+of the Flash. When setting, the EEPROM size must be specified in bytes and it
+must be one of the permitted sizes according to the datasheet. Settings are
+written immediately but only take effect on MCU reset. EEPROM emulation
+requires additional firmware support and the minumum EEPROM size may not be
+the same as the minimum that the hardware supports. Set the EEPROM size to 0
+in order to disable this feature.
+
+@example
+at91samd eeprom
+at91samd eeprom 1024
+@end example
+@end deffn
+
+@deffn Command {at91samd bootloader}
+Shows or sets the bootloader size configuration, stored in the User Row of the
+Flash. This is called the BOOTPROT region. When setting, the bootloader size
+must be specified in bytes and it must be one of the permitted sizes according
+to the datasheet. Settings are written immediately but only take effect on
+MCU reset. Setting the bootloader size to 0 disables bootloader protection.
+
+@example
+at91samd bootloader
+at91samd bootloader 16384
+@end example
+@end deffn
+
 @end deffn
 
 @anchor{at91sam3}