X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Fboard%2Fhitex_stm32-performancestick.cfg;h=82fb169619ed33a0b7771efccde76a948987f2fd;hb=f1427cca3cc6097a4635b4095ad1e30c8a508ac0;hp=5effbd960b4454705a4eee95f968d80b5c5a13b9;hpb=dbbc9c41f7db210b0a4e226540a28e0a8a5019bf;p=openocd.git

diff --git a/tcl/board/hitex_stm32-performancestick.cfg b/tcl/board/hitex_stm32-performancestick.cfg
index 5effbd960b..82fb169619 100644
--- a/tcl/board/hitex_stm32-performancestick.cfg
+++ b/tcl/board/hitex_stm32-performancestick.cfg
@@ -1,50 +1,16 @@
 # Hitex stm32 performance stick
 
-if { [info exists CHIPNAME] } {	
-   set  _CHIPNAME $CHIPNAME    
-} else {	 
-   set  _CHIPNAME stm32_hitex
-}
-
-if { [info exists ENDIAN] } {	
-   set  _ENDIAN $ENDIAN    
-} else {	 
-   set  _ENDIAN little
-}
-
-# set jtag speed
-jtag_khz 500
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
 reset_config trst_and_srst
 
-#jtag scan chain
-# The CPU
-if { [info exists CPUTAPID ] } {
-   set _CPUTAPID $CPUTAPID
-} else {
-  # See STM Document RM0008
-  # Section 26.6.3
-   set _CPUTAPID 0x3ba00477
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+source [find interface/ftdi/stm32-stick.cfg]
 
-# The boundery scan register, leave the "expected-id" undefined.
-jtag newtap $_CHIPNAME bs  -irlen 5 -ircapture 0x1 -irmask 0x1 
+set  CHIPNAME stm32_hitex
+source [find target/stm32f1x.cfg]
 
 # configure str750 connected to jtag chain
-jtag newtap $_CHIPNAME unknown -irlen 4 -ircapture 0x1 -irmask 0x0f
-
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0
+# FIXME -- source [find target/str750.cfg] after cleaning that up
+jtag newtap str750 cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id 0x4f1f0041
 
-#
-flash bank stm32x 0 0 0 0 0
+# for some reason this board like to startup @ 500kHz
+adapter_khz 500
 
-# For more information about the configuration files, take a look at:
-# openocd.texi