X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Ftarget%2Fat91sam7sx.cfg;h=4b3cab43cd63d0bb4a549d978cf5d7fcaf356072;hb=335bafbb2561d92d1631050e6aa3c4ab93e3644e;hp=80186eca8024192b5cc5c6e7504698465c3e5172;hpb=ce89c7bf6588c7b2800c4ca453278b6f94795130;p=openocd.git

diff --git a/tcl/target/at91sam7sx.cfg b/tcl/target/at91sam7sx.cfg
index 80186eca80..4b3cab43cd 100644
--- a/tcl/target/at91sam7sx.cfg
+++ b/tcl/target/at91sam7sx.cfg
@@ -1,19 +1,19 @@
 #use combined on interfaces or targets that can't set TRST/SRST separately
 reset_config srst_only srst_pulls_trst
 
-if { [info exists CHIPNAME] } {	
-   set  _CHIPNAME $CHIPNAME    
-} else {	 
-   set  _CHIPNAME at91sam7s
+if { [info exists CHIPNAME] } {
+   set _CHIPNAME $CHIPNAME
+} else {
+   set _CHIPNAME at91sam7s
 }
 
-if { [info exists ENDIAN] } {	
-   set  _ENDIAN $ENDIAN    
-} else {	 
-   set  _ENDIAN little
+if { [info exists ENDIAN] } {
+   set _ENDIAN $ENDIAN
+} else {
+   set _ENDIAN little
 }
 
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
    set _CPUTAPID 0x3f0f0f0f
@@ -24,32 +24,30 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CP
 set _TARGETNAME $_CHIPNAME.cpu
 
 target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
-$_TARGETNAME configure -event reset-init { 
+$_TARGETNAME configure -event reset-init {
         soft_reset_halt
         # RSTC_CR : Reset peripherals
         mww 0xfffffd00 0xa5000004
         # disable watchdog
-	mww 0xfffffd44 0x00008000	
+	mww 0xfffffd44 0x00008000
 	# enable user reset
-	mww 0xfffffd08 0xa5000001	
+	mww 0xfffffd08 0xa5000001
 	# CKGR_MOR : enable the main oscillator
-	mww 0xfffffc20 0x00000601	
+	mww 0xfffffc20 0x00000601
 	sleep 10
 	# CKGR_PLLR: 96.1097 MHz
-	mww 0xfffffc2c 0x00481c0e 	
+	mww 0xfffffc2c 0x00481c0e
 	sleep 10
 	# PMC_MCKR : MCK = PLL / 2 ~= 48 MHz
-	mww 0xfffffc30 0x00000007	
+	mww 0xfffffc30 0x00000007
 	sleep 10
 	# MC_FMR: flash mode (FWS=1,FMCN=73)
-	mww 0xffffff60 0x00490100	
-	sleep 100        
+	mww 0xffffff60 0x00490100
+	sleep 100
 }
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0
 
 #flash bank <driver> <base_addr> <size> <chip_width> <bus_width> <target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector> <page_size> <num_nvmbits> <ext_freq_khz>]
-flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432
-
-# For more information about the configuration files, take a look at:
-# openocd.texi
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME at91sam7 0 0 0 0 $_TARGETNAME 0 0 0 0 0 0 0 18432