X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Ftarget%2Fstm32f0x.cfg;h=baac9b68d1e84f546083b3aad35e6e3b1c3f5b64;hb=ff555afc02d50ca57fc6e71787d34a8e985cf115;hp=ff6d7f14a111ec35ff63c972ee438a37d90e476a;hpb=a1bbf4b75bc68aeed3c72e37b302bb36757401c2;p=openocd.git

diff --git a/tcl/target/stm32f0x.cfg b/tcl/target/stm32f0x.cfg
index ff6d7f14a1..baac9b68d1 100644
--- a/tcl/target/stm32f0x.cfg
+++ b/tcl/target/stm32f0x.cfg
@@ -4,6 +4,7 @@
 # stm32 devices support SWD transports only.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -21,6 +22,14 @@ if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE 0x1000
 }
 
+# Allow overriding the Flash bank size
+if { [info exists FLASH_SIZE] } {
+	set _FLASH_SIZE $FLASH_SIZE
+} else {
+	# autodetect size
+	set _FLASH_SIZE 0
+}
+
 #jtag scan chain
 if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
@@ -31,15 +40,16 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
 # flash size will be probed
 set _FLASHNAME $_CHIPNAME.flash
-flash bank $_FLASHNAME stm32f1x 0x08000000 0 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32f1x 0x08000000 $_FLASH_SIZE 0 0 $_TARGETNAME
 
 # adapter speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
 adapter_khz 1000
@@ -53,3 +63,33 @@ if {![using_hla]} {
    # perform a soft reset
    cortex_m reset_config sysresetreq
 }
+
+proc stm32f0x_default_reset_start {} {
+	# Reset clock is HSI (8 MHz)
+	adapter_khz 1000
+}
+
+proc stm32f0x_default_examine_end {} {
+	# Enable debug during low power modes (uses more power)
+	mmw 0x40015804 0x00000006 0 ;# DBGMCU_CR |= DBG_STANDBY | DBG_STOP
+
+	# Stop watchdog counters during halt
+	mmw 0x40015808 0x00001800 0 ;# DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
+}
+
+proc stm32f0x_default_reset_init {} {
+	# Configure PLL to boost clock to HSI x 6 (48 MHz)
+	mww 0x40021004 0x00100000   ;# RCC_CFGR = PLLMUL[2]
+	mmw 0x40021000 0x01000000 0 ;# RCC_CR[31:16] |= PLLON
+	mww 0x40022000 0x00000011   ;# FLASH_ACR = PRFTBE | LATENCY[0]
+	sleep 10                    ;# Wait for PLL to lock
+	mmw 0x40021004 0x00000002 0 ;# RCC_CFGR |= SW[1]
+
+	# Boost JTAG frequency
+	adapter_khz 8000
+}
+
+# Default hooks
+$_TARGETNAME configure -event examine-end { stm32f0x_default_examine_end }
+$_TARGETNAME configure -event reset-start { stm32f0x_default_reset_start }
+$_TARGETNAME configure -event reset-init { stm32f0x_default_reset_init }