X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Ftarget%2Fstr710.cfg;h=d26a8b1cf0650ed89b209b28245418b3e1951361;hb=199acf668e08457e972ab2cff10fd6327a33c4fb;hp=39745717d79208191bd9b5c7307f2ed494d0d213;hpb=ce89c7bf6588c7b2800c4ca453278b6f94795130;p=openocd.git
diff --git a/tcl/target/str710.cfg b/tcl/target/str710.cfg
index 39745717d7..d26a8b1cf0 100644
--- a/tcl/target/str710.cfg
+++ b/tcl/target/str710.cfg
@@ -1,22 +1,22 @@
#start slow, speed up after reset
-jtag_khz 10
+adapter_khz 10
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME str710
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME str710
}
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
+if { [info exists ENDIAN] } {
+ set _ENDIAN $ENDIAN
+} else {
+ set _ENDIAN little
}
-if { [info exists CPUTAPID] } {
- set _CPUTAPID $CPUTAPID
-} else {
- set _CPUTAPID 0x3f0f0f0f
+if { [info exists CPUTAPID] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ set _CPUTAPID 0x3f0f0f0f
}
#use combined on interfaces or targets that can't set TRST/SRST separately
@@ -27,20 +27,27 @@ reset_config trst_and_srst srst_pulls_trst
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID
set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi
+target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME
-$_TARGETNAME configure -event reset-start { jtag_khz 10 }
-$_TARGETNAME configure -event reset-init { jtag_khz 6000 }
+$_TARGETNAME configure -event reset-start { adapter_khz 10 }
+$_TARGETNAME configure -event reset-init {
+ adapter_khz 6000
+
+# Because the hardware cannot be interrogated for the protection state
+# of sectors, initialize all the sectors to be unprotected. The initial
+# state is reflected by the driver, too.
+ flash protect 0 0 last off
+ flash protect 1 0 last off
+}
$_TARGETNAME configure -event gdb-flash-erase-start {
flash protect 0 0 7 off
flash protect 1 0 1 off
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x2000C000 -work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x2000C000 -work-area-size 0x4000 -work-area-backup 0
#flash bank str7x 0 0
-flash bank str7x 0x40000000 0x00040000 0 0 0 STR71x
-flash bank str7x 0x400C0000 0x00004000 0 0 0 STR71x
-
-# For more information about the configuration files, take a look at:
-# openocd.texi
+set _FLASHNAME $_CHIPNAME.flash0
+flash bank $_FLASHNAME str7x 0x40000000 0x00040000 0 0 $_TARGETNAME STR71x
+set _FLASHNAME $_CHIPNAME.flash1
+flash bank $_FLASHNAME str7x 0x400C0000 0x00004000 0 0 $_TARGETNAME STR71x