X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Ftarget%2Fstr730.cfg;h=48d3134aac151c92724dcc14dd0a2bf8fca6ae14;hb=d651d7109f368f66eba481404e9d063ec1219a69;hp=53d7e1a1e4294e8175d2249061937f936c4f22f5;hpb=ce89c7bf6588c7b2800c4ca453278b6f94795130;p=openocd.git

diff --git a/tcl/target/str730.cfg b/tcl/target/str730.cfg
index 53d7e1a1e4..48d3134aac 100644
--- a/tcl/target/str730.cfg
+++ b/tcl/target/str730.cfg
@@ -1,47 +1,54 @@
 #STR730 CPU
 
-jtag_khz 3000
+adapter_khz 3000
 
-if { [info exists CHIPNAME] } {	
-   set  _CHIPNAME $CHIPNAME    
-} else {	 
-   set  _CHIPNAME str730
+if { [info exists CHIPNAME] } {
+   set _CHIPNAME $CHIPNAME
+} else {
+   set _CHIPNAME str730
 }
 
-if { [info exists ENDIAN] } {	
-   set  _ENDIAN $ENDIAN    
-} else {	 
-   set  _ENDIAN little
+if { [info exists ENDIAN] } {
+   set _ENDIAN $ENDIAN
+} else {
+   set _ENDIAN little
 }
 
-if { [info exists CPUTAPID] } {	
-   set  _CPUTAPID $CPUTAPID    
-} else {	 
-   set  _CPUTAPID 0x3f0f0f0f
+if { [info exists CPUTAPID] } {
+   set _CPUTAPID $CPUTAPID
+} else {
+   set _CPUTAPID 0x3f0f0f0f
 }
 
 #use combined on interfaces or targets that can't set TRST/SRST separately
-#reset_config trst_and_srst srst_pulls_trst
 reset_config trst_and_srst srst_pulls_trst
 
 #jtag scan chain
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0x0f -expected-id $_CPUTAPID
 
 #jtag nTRST and nSRST delay
-jtag_nsrst_delay 500
+adapter_nsrst_delay 500
 jtag_ntrst_delay 500
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm7tdmi -endian little -chain-position 0 -variant arm7tdmi
+target create $_TARGETNAME arm7tdmi -endian little -chain-position 0
 
-$_TARGETNAME configure -event reset-start { jtag_khz 10 }
-$_TARGETNAME configure -event reset-init { jtag_khz 3000 }
+$_TARGETNAME configure -event reset-start { adapter_khz 10 }
+$_TARGETNAME configure -event reset-init {
+	adapter_khz 3000
+
+# Because the hardware cannot be interrogated for the protection state
+# of sectors, initialize all the sectors to be unprotected. The initial
+# state is reflected by the driver, too.
+	flash protect 0 0 last off
+}
 $_TARGETNAME configure -event gdb-flash-erase-start {
 	flash protect 0 0 7 off
 }
 
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000 -work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0xA0000000 -work-area-size 0x4000 -work-area-backup 0
 
 #flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str7x 0x20000000 0x00040000 0 0 0 STR3x
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME str7x 0x80000000 0x00040000 0 0 $_TARGETNAME STR73x