X-Git-Url: https://review.openocd.org/gitweb?a=blobdiff_plain;f=tcl%2Ftarget%2Fstr912.cfg;h=7426276bfbd1f6be406aca1acfec503f4661359c;hb=38ac08c1c25adf42cf20e48e10e6ddeab6a12d71;hp=a16c83a04e0acd9ff7057a92b7dd35e8d2fa9cf1;hpb=215a5f7442773693045613cff9e3ce3c7f7e9678;p=openocd.git

diff --git a/tcl/target/str912.cfg b/tcl/target/str912.cfg
index a16c83a04e..7426276bfb 100644
--- a/tcl/target/str912.cfg
+++ b/tcl/target/str912.cfg
@@ -1,56 +1,58 @@
 # script for str9
 
 if { [info exists CHIPNAME] } {
-   set  _CHIPNAME $CHIPNAME
+   set _CHIPNAME $CHIPNAME
 } else {
-   set  _CHIPNAME str912
+   set _CHIPNAME str912
 }
 
 if { [info exists ENDIAN] } {
-   set  _ENDIAN $ENDIAN
+   set _ENDIAN $ENDIAN
 } else {
-   set  _ENDIAN little
+   set _ENDIAN little
 }
 
 # jtag speed. We need to stick to 16kHz until we've finished reset.
-jtag_rclk 16
+adapter speed 16
 
-adapter_nsrst_delay 100
+adapter srst delay 100
 jtag_ntrst_delay 100
 
 #use combined on interfaces or targets that can't set TRST/SRST separately
 reset_config trst_and_srst
 
-if { [info exists FLASHTAPID ] } {
+if { [info exists FLASHTAPID] } {
    set _FLASHTAPID $FLASHTAPID
 } else {
    set _FLASHTAPID 0x04570041
 }
 jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 -expected-id $_FLASHTAPID
 
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
    set _CPUTAPID 0x25966041
 }
-jtag newtap $_CHIPNAME cpu   -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
 
-if { [info exists BSTAPID ] } {
+if { [info exists BSTAPID] } {
    set _BSTAPID $BSTAPID
 } else {
+   # possible values: 0x1457f041, 0x2457f041
+   # we ignore version in check below
    set _BSTAPID 0x1457f041
 }
-jtag newtap $_CHIPNAME bs    -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID
+jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 -expected-id $_BSTAPID -ignore-version
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm966e
+target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position $_TARGETNAME
 
-$_TARGETNAME configure -event reset-start { jtag_rclk 16 }
+$_TARGETNAME configure -event reset-start { adapter speed 16 }
 
 $_TARGETNAME configure -event reset-init {
 	# We can increase speed now that we know the target is halted.
-	#jtag_rclk 3000
+	#adapter speed 3000
 
 	# -- Enable 96K RAM
 	# PFQBC enabled / DTCM & AHB wait-states disabled
@@ -67,6 +69,3 @@ set _FLASHNAME $_CHIPNAME.flash0
 flash bank $_FLASHNAME str9x 0x00000000 0x00080000 0 0 $_TARGETNAME
 set _FLASHNAME $_CHIPNAME.flash1
 flash bank $_FLASHNAME str9x 0x00080000 0x00008000 0 0 $_TARGETNAME
-
-# For more information about the configuration files, take a look at:
-# openocd.texi