jtag/drivers: give ANGIE a new PID after renumeration Give ANGIE a new PID after renumeration to be able to distinguish the two cases (programmed and not programmed) Change-Id: I30a91d8ed2e8e261221488b98d40a027ca41da52 Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7991 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
jtag/drivers: add new VIDs for angie driver - add a check for a returned value add a line that checks the returned value of set signals function add two VIDs of other original boards (have onboard angie architecture) so angie driver can connect to them and change their VID after renumeration. Change-Id: Ide4f1f6f38168a410191bf3ff75bcd59dcf7ef50 Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7795 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
jtag/drivers: Add new driver for ANGIE USB-JTAG Adapter This is the driver code for NanoXplore's ANGIE USB-JTAG Adapter. The driver is based on the openULINK project. This driver communicate with ANGIE's firmware in order to establish JTAG protocol to debug the target chip. Since the ANGIE Adapter has a Spartan-6 FPGA in addition to the FX2 microcontroller, the driver adds two functions, one to download the firmware (embedded C) to the FX2, and the second to program the FPGA with its bitstream. Add ANGIE's configuration file to tcl/interface/ Add the device VID/PID to 60-openocd.rules file. Add ANGIE to OpenOCD's documentation Change-Id: Id17111c74073da01450d43d466e11b0cc086691f Signed-off-by: Ahmed BOUDJELIDA <aboudjelida@nanoxplore.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7702 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
jtag/stlink: add STLINK-V3PWR support STLINK-V3PWR is both a standalone debugger probe compatible with STLINK-V3 and a source measurement unit (SMU). Link: http://www.st.com/stlink-v3pwr This code adds support for the debugger probe functionality. Change-Id: Ib056e55722528f922c5574bb6fbf77e2f2b2b0c1 Signed-off-by: Laurent LEMELE <laurent.lemele@st.com> Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7755 Tested-by: jenkins
contrib: add GPL license tag on files that miss it Some file miss completely the license tag. Add the SPDX tag, using the same GPL-2.0-or-later license of the OpenOCD project. The SPDX tag on files *.c is incorrect, as it should use the C99 single line comment using '//'. But current checkpatch doesn't allow C99 comments, so keep using standard C comments, by now. Change-Id: I24bd362eeb6b74f09aceb9b757d45cbfa4afe334 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7160 Tested-by: jenkins
jtag: add esp_usb_jtag driver This driver is used with the ESP32 chips which has builtin USB-JTAG interface. e.g. with ESP32-C3, ESP32-S3 Signed-off-by: Erhan Kurubas <erhan.kurubas@espressif.com> Change-Id: If966268cb8d26f76540dd5440245a17ed0b72c61 Reviewed-on: https://review.openocd.org/c/openocd/+/6943 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
contrib/udev: Add missing J-Link USB PID See libjaylink/contrib/99-libjaylink.rules Change-Id: I36733e18eb4bc11828c5fa563c687d28be9e34bd Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: https://review.openocd.org/c/openocd/+/6778 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
udev: add ASIX Presto programmer The driver is in OpenOCD since 2007, but the USB VID/PID have never been listed in udev rules. Change-Id: I77df469929dd7f6b6483678c0e76f22c30a7614c Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/6563 Tested-by: jenkins
stlink: Add PID for V3 device without MSD Add the 0x3754 PID used by some STLINK-V3 devices when MSD has been disabled. This PID has been observed on a Nucleo-G431RB board. Signed-off-by: Andreas Sandberg <andreas@sandberg.uk> Change-Id: Idb85874fa5a9dff5940bae7e95426a956693b976 Reviewed-on: https://review.openocd.org/c/openocd/+/6555 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
tcl: add lattice ECP5 family support Add support for ECP5 FPGA targets and board based on this chips: Radiona ULX3S and Lambdaconcept ECPIX-5 Change-Id: I932fc6e2458cda7d63ac21579acddea5b53410bc Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-on: https://review.openocd.org/c/openocd/+/6112 Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
tcl/interface: add Ashling Opella-LD FTDI config files Adding Ashling's FTDI based Debug adapter Opella-LD's JTAG and SWD config files Change-Id: Ie0e82e3b8326de37641901f5c825372cab31de58 Signed-off-by: ranjith.tc@ashling.com Reviewed-on: http://openocd.zylin.com/6379 Tested-by: jenkins Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
udev rules: add OSBDM device Change-Id: I7221a6b3fe6fcd4f17ea664c10fd32c645e21d7c Signed-off-by: Jiri Kastner <cz172638@gmail.com> Reviewed-on: http://openocd.zylin.com/6198 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
udev rules: add missing Altera USB Blaster devices All Altera USB Blaster devices require a dedicated line in the udev rules, but some USB VID/PID present in interface and board config file is missing in udev rules. Add the missing Altera USB Blaster devices in udev rules. While there, fix an incorrect pair VID/PID that are reported swapped inside a comment. Change-Id: I2d67e90b10db99ef2638405585859c1393456f65 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/6102 Tested-by: jenkins
udev rules: add missing ftdi USB VID/PID All ftdi devices require a dedicated line in the udev rules, but some USB VID/PID present in interface and board config file is missing in udev rules. Add the missing ftdi devices in udev rules. Change-Id: I850a4a95a2d4bb63b3fd09be803be8c23c4d6b49 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/6101 Tested-by: jenkins
tcl/interface/ftdi: Add PLS SPC5 debugger config Change-Id: I694201db0811beebc94e87822c87fbfc6aecc4c4 Signed-off-by: Andrew Wesie <awesie@gmail.com> Reviewed-on: http://openocd.zylin.com/6081 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
tcl/interface/ftdi: Add miniWiggler debugger config Change-Id: I91f73a377cd9525008d09fda7a7c58d498014b74 Signed-off-by: Andrew Wesie <awesie@gmail.com> Reviewed-on: http://openocd.zylin.com/6111 Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com> Tested-by: jenkins
udev: fix permission for Ambiq Micro EVK's Commit 68e204f1e91a ("udev: Add rules for Ambiq Micro EVK's.") was initially proposed as http://openocd.zylin.com/3429/ then replaced by http://openocd.zylin.com/3980/ The initial proposal was for file '99-openocd.rules', in which MODE="664" was the norm. After merge of http://openocd.zylin.com/2804/ the new udev rules in '60-openocd.rules' switched to MODE="660", but the evolution of the above patch missed this change. Switch udev rules of Ambiq Micro EVK's to MODE="660" and uniform them to the rest of the file. Change-Id: I4b4eea535184ee8569da3264bff4f1fafb5bce4d Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Fixes: 68e204f1e91a ("udev: Add rules for Ambiq Micro EVK's.") Reviewed-on: http://openocd.zylin.com/6004 Tested-by: jenkins
contrib: udev file for Cypress SuperSpeed Explorer kit lsusb output: Bus 003 Device 011: ID 04b4:0007 Cypress Semiconductor Corp. Couldn't open device, some information will be missing Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x04b4 Cypress Semiconductor Corp. idProduct 0x0007 bcdDevice 0.00 iManufacturer 1 iProduct 2 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 114 bNumInterfaces 4 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 100mA Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 0 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Union: bMasterInterface 0 bSlaveInterface 1 CDC Call Management: bmCapabilities 0x00 bDataInterface 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 4 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 5 bInterfaceProtocol 0 iInterface 0 Change-Id: I62f0300199da3551c8774a4a5a4cd106a3ab2904 Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Jiri Kastner <cz172638@gmail.com> Reviewed-on: http://openocd.zylin.com/3611 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
60-openocd.rules: add ULINKplus CMSIS-DAP based adapter Change-Id: I5935e0a184b8995122d197046ef8fb4e7eefb884 Signed-off-by: Tarek BOCHKATI <tarek.bouchkati@st.com> Reviewed-on: http://openocd.zylin.com/5926 Reviewed-by: Tarek BOCHKATI <tarek.bouchkati@gmail.com> Reviewed-by: Tomas Vanek <vanekt@fbl.cz> Tested-by: jenkins
nulink: add minimal support for Nu-Link2 Implementation largely taken from Nuvoton github https://github.com/OpenNuvoton/OpenOCD-Nuvoton Reset is still not fully compatible with OpenOCD framework. Adapted to hidapi. Change-Id: Ieb1791b1b7f0b444c15c9668f8f2bcf34975d48f Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Signed-off-by: Zale Yu <cyyu@nuvoton.com> Reviewed-on: http://openocd.zylin.com/5720 Tested-by: jenkins Reviewed-by: Saravanan Sekar <saravanan@linumiz.com> Reviewed-by: Marc Schink <dev@zapb.de>