tcl/interface: add SPDX tag For historical reasons, no license information was added to the tcl files. This makes trivial adding the SPDX tag through script: fgrep -rL SPDX tcl/interface | while read a;do \ sed -i '1{i# SPDX-License-Identifier: GPL-2.0-or-later\n }' $a;done With no specific license information from the author, let's extend the OpenOCD project license GPL-2.0-or-later to the files. Change-Id: I7bd6a628e9e153fc477cddf9b97087a39ec48aa7 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: https://review.openocd.org/c/openocd/+/7029 Tested-by: jenkins
tcl/interface: Adapt config files to new parport command syntax Change-Id: Iffe7a04c36c6ec680497081a99d55b8c69f8f079 Signed-off-by: Marc Schink <dev@zapb.de> Reviewed-on: http://openocd.zylin.com/6386 Tested-by: jenkins Reviewed-by: Antonio Borneo <borneo.antonio@gmail.com>
tcl: replace command "interface" with "adapter driver" Avoid annoying "deprecated" messages while running the scripts distributed with OpenOCD code. Change automatically created with command sed -i 's/^interface /adapter driver /' $(find tcl/ -type f) Change-Id: I2291dfb96e164beecbeb3366ce83f9df2ad6c197 Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com> Reviewed-on: http://openocd.zylin.com/5283 Reviewed-by: Marc Schink <dev@zapb.de> Tested-by: jenkins Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
tcl/interface/parport: default to sane value on non-windows systems When using ppdev driver 0 is the most appropriate default value as it corresponds to /dev/parport0. Raw port address is suitable only for direct access (I think that's parport-giveio on windows). Reported by danitool on IRC. Change-Id: I983c22251de6601b433ad31aaf660fb664cee7e9 Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-on: http://openocd.zylin.com/2572 Reviewed-by: Andreas Färber <afaerber@suse.de> Tested-by: jenkins Reviewed-by: Spencer Oliver <spen@spen-soft.co.uk>
interface configs: Fix whitespace and other issues. Change-Id: I98825c7fb9bdee75b69b06005ed12a3f64ec4db4 Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Reviewed-on: http://openocd.zylin.com/139 Tested-by: jenkins Reviewed-by: Peter Stuge <peter@stuge.se>
PARPORT: add PARPORTADDR tcl variable Add PARPORTADDR tcl variable making it easier to change parallel port address in scripts. Signed-off-by: Spencer Oliver <ntfreak@users.sourceforge.net>
interface: Changed parport address to LPT1 Changed the parport address to LPT1, since it's the most obvious default value. Signed-off-by: Edgar Grimberg <edgar.grimberg@zylin.com>
parport (mostly) doc fixes The "parport_port" commands generally don't *require* a port_number; they're of the "apply any parameter, then print result" variety. Update the User's Guide accordingly. Some of those commands are intended to be write-once: parport_port, and parport_cable. Say so. Use proper EBNF for the parport_write_on_exit parameter. Parport address 0xc8b8 is evidently mutant. Say so in the "parport.cfg" file, to avoid breaking anyone with that mutant config. But update the User's Guide to include a sane example for the LP2 port. Finally document the "presto_serial" command. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
finish removing deprecated/obsolete commands It's been about a year since these were deprecated and, in most cases, removed. There's no point in carrying that documentation, or backwards compatibility for "jtag_device" and "jtag_speed", around forever. (Or a few remnants of obsolete code...) Removed a few obsolete uses of "jtag_speed": - The Calao stuff hasn't worked since July 2008. (Those Atmel targets need to work with a 32KHz core clock after reset until board-specific init-reset code sets up the PLL and enables a faster JTAg clock.) - Parport speed controls don't actually work (tops out at about 1 MHz on typical HW). - In general, speed controls need to live in board.cfg files (or sometimes target.cfg files), not interface.cfg ... Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move TCL script files -- Step 2 of 2: - Move src/tcl to tcl/. - Update top Makefile.am to use new path name. git-svn-id: svn://svn.berlios.de/openocd/trunk@1919 b42882b7-edfa-0310-969c-e2dbd0fdcd60