tcl/target/lpc1xxx.cfg

   1 # Main file for NXP LPC1xxx series Cortex-M0/0+/3 parts
   2 #
   3 # !!!!!!
   4 #
   5 # This file should not be included directly, rather by the lpc11xx.cfg,
   6 # lpc13xx.cfg, lpc17xx.cfg, etc. which set the needed variables to the
   7 # appropriate values.
   8 #
   9 # !!!!!!
  10
  11 # LPC8xx chips support only SWD transport.
  12 # LPC11xx chips support only SWD transport.
  13 # LPC12xx chips support only SWD transport.
  14 # LPC11Uxx chips support both JTAG and SWD transports.
  15 # LPC13xx chips support both JTAG and SWD transports.
  16 # LPC17xx chips support both JTAG and SWD transports.
  17 # Adapt based on what transport is active.
  18 source [find target/swj-dp.tcl]
  19
  20 if { [info exists CHIPNAME] } {
  21         set _CHIPNAME $CHIPNAME
  22 } else {
  23         error "CHIPNAME not set. Please do not include lpc1xxx.cfg directly, but the specific chip configuration file (lpc11xx.cfg, lpc13xx.cfg, lpc17xx.cfg, etc)."
  24 }
  25
  26 if { [info exists CHIPSERIES] } {
  27         # Validate chip series is supported
  28         if { $CHIPSERIES != "lpc800" && $CHIPSERIES != "lpc1100" && $CHIPSERIES != "lpc1200" && $CHIPSERIES != "lpc1300" && $CHIPSERIES != "lpc1700" } {
  29                 error "Unsupported LPC1xxx chip series specified."
  30         }
  31         set _CHIPSERIES $CHIPSERIES
  32 } else {
  33         error "CHIPSERIES not set. Please do not include lpc1xxx.cfg directly, but the specific chip configuration file (lpc11xx.cfg, lpc13xx.cfg, lpc17xx.cfg, etc)."
  34 }
  35
  36 # After reset, the chip is clocked by an internal RC oscillator.
  37 # When board-specific code (reset-init handler or device firmware)
  38 # configures another oscillator and/or PLL0, set CCLK to match; if
  39 # you don't, then flash erase and write operations may misbehave.
  40 # (The ROM code doing those updates cares about core clock speed...)
  41 # CCLK is the core clock frequency in KHz
  42 if { [info exists CCLK] } {
  43         # Allow user override
  44         set _CCLK $CCLK
  45 } else {
  46         # LPC8xx/LPC11xx/LPC12xx/LPC13xx use a 12MHz one, LPC17xx uses a 4MHz one
  47         if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" || $_CHIPSERIES == "lpc1300" } {
  48                 set _CCLK 12000
  49         } elseif { $_CHIPSERIES == "lpc1700" } {
  50                 set _CCLK 4000
  51         }
  52 }
  53
  54 if { [info exists CPUTAPID] } {
  55         # Allow user override
  56         set _CPUTAPID $CPUTAPID
  57 } else {
  58         # LPC8xx/LPC11xx/LPC12xx use a Cortex M0/M0+ core, LPC13xx/LPC17xx use a Cortex M3 core
  59         if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" } {
  60                 set _CPUTAPID 0x0bb11477
  61         } elseif { $_CHIPSERIES == "lpc1300" || $_CHIPSERIES == "lpc1700" } {
  62                 if { [using_jtag] } {
  63                         set _CPUTAPID 0x4ba00477
  64                 } {
  65                         set _CPUTAPID 0x2ba01477
  66                 }
  67         }
  68 }
  69
  70 if { [info exists WORKAREASIZE] } {
  71         set _WORKAREASIZE $WORKAREASIZE
  72 } else {
  73         error "WORKAREASIZE is not set. The $CHIPNAME part is available in several Flash and RAM size configurations. Please set WORKAREASIZE."
  74 }
  75
  76 swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
  77
  78 set _TARGETNAME $_CHIPNAME.cpu
  79 target create $_TARGETNAME cortex_m -chain-position $_TARGETNAME
  80
  81 # The LPC11xx devices have 2/4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  82 # The LPC12xx devices have 4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  83 # The LPC11Uxx devices have 4/6/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  84 # The LPC13xx devices have 4/8kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  85 # The LPC17xx devices have 8/16/32kB of SRAM in the ARMv7-M "Code" area (at 0x10000000)
  86 $_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size $_WORKAREASIZE
  87
  88 # The LPC11xx devies have 8/16/24/32/48/56/64kB of flash memory (at 0x00000000)
  89 # The LPC12xx devies have 32/48/64/80/96/128kB of flash memory (at 0x00000000)
  90 # The LPC11Uxx devies have 16/24/32/40/48/64/96/128kB of flash memory (at 0x00000000)
  91 # The LPC13xx devies have 8/16/32kB of flash memory (at 0x00000000)
  92 # The LPC17xx devies have 32/64/128/256/512kB of flash memory (at 0x00000000)
  93 #
  94 # All are compatible with the "lpc1700" variant of the LPC2000 flash driver
  95 # (same cmd51 destination boundary alignment, and all three support 256 byte
  96 # transfers).
  97 #
  98 # flash bank <name> lpc2000 <base> <size> 0 0 <target#> <variant> <clock> [calc checksum]
  99 set _FLASHNAME $_CHIPNAME.flash
 100 flash bank $_FLASHNAME lpc2000 0x0 0 0 0 $_TARGETNAME \
 101         auto $_CCLK calc_checksum
 102
 103 if { $_CHIPSERIES == "lpc800" || $_CHIPSERIES == "lpc1100" || $_CHIPSERIES == "lpc1200" || $_CHIPSERIES == "lpc1300" } {
 104         # Do not remap 0x0000-0x0200 to anything but the flash (i.e. select
 105         # "User Flash Mode" where interrupt vectors are _not_ remapped,
 106         # and reside in flash instead).
 107         #
 108         # Table 8. System memory remap register (SYSMEMREMAP, address 0x4004 8000) bit description
 109         # Bit Symbol Value Description
 110         # 1:0 MAP          System memory remap
 111         #            0x0   Boot Loader Mode. Interrupt vectors are re-mapped to Boot ROM.
 112         #            0x1   User RAM Mode. Interrupt vectors are re-mapped to Static RAM.
 113         #            0x2   User Flash Mode. Interrupt vectors are not re-mapped and reside in Flash.
 114         # 31:2 -     -     Reserved.
 115         $_TARGETNAME configure -event reset-init {
 116                 mww 0x40048000 0x02
 117         }
 118 } elseif { $_CHIPSERIES == "lpc1700" } {
 119         # Do not remap 0x0000-0x0020 to anything but the flash (i.e. select
 120         # "User Flash Mode" where interrupt vectors are _not_ remapped,
 121         # and reside in flash instead).
 122         #
 123         # See Table 612. Memory Mapping Control register (MEMMAP - 0x400F C040) bit description
 124         # Bit Symbol Value Description Reset
 125         # value
 126         # 0 MAP Memory map control. 0
 127         # 0 Boot mode. A portion of the Boot ROM is mapped to address 0.
 128         # 1 User mode. The on-chip Flash memory is mapped to address 0.
 129         # 31:1 - Reserved. The value read from a reserved bit is not defined. NA
 130         #
 131         # http://ics.nxp.com/support/documents/microcontrollers/?scope=LPC1768&type=user
 132         $_TARGETNAME configure -event reset-init {
 133                 mww 0x400FC040 0x01
 134         }
 135 }
 136
 137 # Run with *real slow* clock by default since the
 138 # boot rom could have been playing with the PLL, so
 139 # we have no idea what clock the target is running at.
 140 adapter_khz 10
 141
 142 # delays on reset lines
 143 adapter_nsrst_delay 200
 144 if {[using_jtag]} {
 145  jtag_ntrst_delay 200
 146 }
 147
 148 # LPC8xx (Cortex M0+ core) support SYSRESETREQ
 149 # LPC11xx/LPC12xx (Cortex M0 core) support SYSRESETREQ
 150 # LPC13xx/LPC17xx (Cortex M3 core) support SYSRESETREQ
 151 if {![using_hla]} {
 152     # if srst is not fitted use SYSRESETREQ to
 153     # perform a soft reset
 154     cortex_m reset_config sysresetreq
 155 }