tcl/target/stm32l4x.cfg

   1 # script for stm32l4x family
   2
   3 #
   4 # stm32l4 devices support both JTAG and SWD transports.
   5 #
   6 source [find target/swj-dp.tcl]
   7 source [find mem_helper.tcl]
   8
   9 if { [info exists CHIPNAME] } {
  10    set _CHIPNAME $CHIPNAME
  11 } else {
  12    set _CHIPNAME stm32l4x
  13 }
  14
  15 set _ENDIAN little
  16
  17 # Work-area is a space in RAM used for flash programming
  18 # Smallest current target has 64kB ram, use 32kB by default to avoid surprises
  19 if { [info exists WORKAREASIZE] } {
  20    set _WORKAREASIZE $WORKAREASIZE
  21 } else {
  22    set _WORKAREASIZE 0x8000
  23 }
  24
  25 #jtag scan chain
  26 if { [info exists CPUTAPID] } {
  27    set _CPUTAPID $CPUTAPID
  28 } else {
  29    if { [using_jtag] } {
  30       # See STM Document RM0351
  31       # Section 44.6.3 - corresponds to Cortex-M4 r0p1
  32       set _CPUTAPID 0x4ba00477
  33    } {
  34       set _CPUTAPID 0x2ba01477
  35    }
  36 }
  37
  38 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
  39 dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
  40
  41 if {[using_jtag]} {
  42    jtag newtap $_CHIPNAME bs -irlen 5
  43 }
  44
  45 set _TARGETNAME $_CHIPNAME.cpu
  46 target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
  47
  48 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
  49
  50 flash bank $_CHIPNAME.flash stm32l4x 0x08000000 0 0 0 $_TARGETNAME
  51 flash bank $_CHIPNAME.otp   stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
  52
  53 if { [info exists QUADSPI] && $QUADSPI } {
  54    set a [llength [flash list]]
  55    set _QSPINAME $_CHIPNAME.qspi
  56    flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
  57 } else {
  58    if { [info exists OCTOSPI1] && $OCTOSPI1 } {
  59       set a [llength [flash list]]
  60       set _OCTOSPINAME1 $_CHIPNAME.octospi1
  61       flash bank $_OCTOSPINAME1 stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
  62    }
  63    if { [info exists OCTOSPI2] && $OCTOSPI2 } {
  64       set b [llength [flash list]]
  65       set _OCTOSPINAME2 $_CHIPNAME.octospi2
  66       flash bank $_OCTOSPINAME2 stmqspi 0x70000000 0 0 0 $_TARGETNAME 0xA0001400
  67    }
  68 }
  69
  70 # Common knowledges tells JTAG speed should be <= F_CPU/6.
  71 # F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
  72 # the safe side.
  73 #
  74 # Note that there is a pretty wide band where things are
  75 # more or less stable, see http://openocd.zylin.com/#/c/3366/
  76 adapter speed 500
  77
  78 adapter srst delay 100
  79 if {[using_jtag]} {
  80  jtag_ntrst_delay 100
  81 }
  82
  83 reset_config srst_nogate
  84
  85 if {![using_hla]} {
  86    # if srst is not fitted use SYSRESETREQ to
  87    # perform a soft reset
  88    cortex_m reset_config sysresetreq
  89 }
  90
  91 $_TARGETNAME configure -event reset-init {
  92         # CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 6 (4 MHz).
  93         # Use MSI 24 MHz clock, compliant even with VOS == 2.
  94         # 3 WS compliant with VOS == 2 and 24 MHz.
  95         mww 0x40022000 0x00000103   ;# FLASH_ACR = PRFTBE | 3(Latency)
  96         mww 0x40021000 0x00000099   ;# RCC_CR = MSI_ON | MSIRGSEL | MSI Range 9
  97         # Boost JTAG frequency
  98         adapter speed 4000
  99 }
 100
 101 $_TARGETNAME configure -event reset-start {
 102         # Reset clock is MSI (4 MHz)
 103         adapter speed 500
 104 }
 105
 106 $_TARGETNAME configure -event examine-end {
 107         # DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
 108         mmw 0xE0042004 0x00000007 0
 109
 110         # Stop watchdog counters during halt
 111         # DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
 112         mmw 0xE0042008 0x00001800 0
 113 }
 114
 115 $_TARGETNAME configure -event trace-config {
 116         # Set TRACE_IOEN; TRACE_MODE is set to async; when using sync
 117         # change this value accordingly to configure trace pins
 118         # assignment
 119         mmw 0xE0042004 0x00000020 0
 120 }