tcl/target/stm32l4x.cfg

   1 # script for stm32l4x family
   2
   3 #
   4 # stm32l4 devices support both JTAG and SWD transports.
   5 #
   6 source [find target/swj-dp.tcl]
   7 source [find mem_helper.tcl]
   8
   9 if { [info exists CHIPNAME] } {
  10    set _CHIPNAME $CHIPNAME
  11 } else {
  12    set _CHIPNAME stm32l4x
  13 }
  14
  15 set _ENDIAN little
  16
  17 # Work-area is a space in RAM used for flash programming
  18 # By default use 40kB (Available RAM in smallest device STM32L412)
  19 if { [info exists WORKAREASIZE] } {
  20    set _WORKAREASIZE $WORKAREASIZE
  21 } else {
  22    set _WORKAREASIZE 0xa000
  23 }
  24
  25 #jtag scan chain
  26 if { [info exists CPUTAPID] } {
  27    set _CPUTAPID $CPUTAPID
  28 } else {
  29    if { [using_jtag] } {
  30       # See STM Document RM0351
  31       # Section 44.6.3 - corresponds to Cortex-M4 r0p1
  32       set _CPUTAPID 0x4ba00477
  33    } {
  34       set _CPUTAPID 0x2ba01477
  35    }
  36 }
  37
  38 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
  39 dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
  40
  41 tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000
  42
  43 if {[using_jtag]} {
  44    jtag newtap $_CHIPNAME bs -irlen 5
  45 }
  46
  47 set _TARGETNAME $_CHIPNAME.cpu
  48 target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
  49
  50 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
  51
  52 set _FLASHNAME $_CHIPNAME.flash
  53 flash bank $_FLASHNAME stm32l4x 0x08000000 0 0 0 $_TARGETNAME
  54 flash bank $_CHIPNAME.otp stm32l4x 0x1fff7000 0 0 0 $_TARGETNAME
  55
  56 if { [info exists QUADSPI] && $QUADSPI } {
  57    set a [llength [flash list]]
  58    set _QSPINAME $_CHIPNAME.qspi
  59    flash bank $_QSPINAME stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
  60 } else {
  61    if { [info exists OCTOSPI1] && $OCTOSPI1 } {
  62       set a [llength [flash list]]
  63       set _OCTOSPINAME1 $_CHIPNAME.octospi1
  64       flash bank $_OCTOSPINAME1 stmqspi 0x90000000 0 0 0 $_TARGETNAME 0xA0001000
  65    }
  66    if { [info exists OCTOSPI2] && $OCTOSPI2 } {
  67       set b [llength [flash list]]
  68       set _OCTOSPINAME2 $_CHIPNAME.octospi2
  69       flash bank $_OCTOSPINAME2 stmqspi 0x70000000 0 0 0 $_TARGETNAME 0xA0001400
  70    }
  71 }
  72
  73 # Common knowledges tells JTAG speed should be <= F_CPU/6.
  74 # F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
  75 # the safe side.
  76 #
  77 # Note that there is a pretty wide band where things are
  78 # more or less stable, see http://openocd.zylin.com/#/c/3366/
  79 adapter speed 500
  80
  81 adapter srst delay 100
  82 if {[using_jtag]} {
  83  jtag_ntrst_delay 100
  84 }
  85
  86 reset_config srst_nogate
  87
  88 if {![using_hla]} {
  89    # if srst is not fitted use SYSRESETREQ to
  90    # perform a soft reset
  91    cortex_m reset_config sysresetreq
  92 }
  93
  94 $_TARGETNAME configure -event examine-end {
  95         # Enable debug during low power modes (uses more power)
  96         # DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
  97         mmw 0xE0042004 0x00000007 0
  98
  99         # Stop watchdog counters during halt
 100         # DBGMCU_APB1_FZ |= DBG_IWDG_STOP | DBG_WWDG_STOP
 101         mmw 0xE0042008 0x00001800 0
 102 }
 103
 104 proc proc_post_enable {_chipname} {
 105         targets $_chipname.cpu
 106
 107         if { [$_chipname.tpiu cget -protocol] eq "sync" } {
 108                 switch [$_chipname.tpiu cget -port-width] {
 109                         1 {
 110                                 mmw 0xE0042004 0x00000060 0x000000c0
 111                                 mmw 0x48001020 0x00000000 0x0000ff00
 112                                 mmw 0x48001000 0x000000a0 0x000000f0
 113                                 mmw 0x48001008 0x000000f0 0x00000000
 114                           }
 115                         2 {
 116                                 mmw 0xE0042004 0x000000a0 0x000000c0
 117                                 mmw 0x48001020 0x00000000 0x000fff00
 118                                 mmw 0x48001000 0x000002a0 0x000003f0
 119                                 mmw 0x48001008 0x000003f0 0x00000000
 120                           }
 121                         4 {
 122                                 mmw 0xE0042004 0x000000e0 0x000000c0
 123                                 mmw 0x48001020 0x00000000 0x0fffff00
 124                                 mmw 0x48001000 0x00002aa0 0x00003ff0
 125                                 mmw 0x48001008 0x00003ff0 0x00000000
 126                           }
 127                 }
 128         } else {
 129                 mmw 0xE0042004 0x00000020 0x000000c0
 130         }
 131 }
 132
 133 $_CHIPNAME.tpiu configure -event post-enable "proc_post_enable $_CHIPNAME"
 134
 135 $_TARGETNAME configure -event reset-init {
 136         # CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 6 (4 MHz).
 137         # Use MSI 24 MHz clock, compliant even with VOS == 2.
 138         # 3 WS compliant with VOS == 2 and 24 MHz.
 139         mww 0x40022000 0x00000103   ;# FLASH_ACR = PRFTBE | 3(Latency)
 140         mww 0x40021000 0x00000099   ;# RCC_CR = MSI_ON | MSIRGSEL | MSI Range 9
 141
 142         # Boost JTAG frequency
 143         adapter speed 4000
 144 }
 145
 146 $_TARGETNAME configure -event reset-start {
 147         # Reset clock is MSI (4 MHz)
 148         adapter speed 500
 149 }