tcl/target/ti_dm365.cfg

   1 #
   2 # Texas Instruments DaVinci family: TMS320DM365
   3 #
   4 if { [info exists CHIPNAME] } {
   5    set _CHIPNAME $CHIPNAME
   6 } else {
   7    set _CHIPNAME dm365
   8 }
   9
  10 # TI boards default to EMU0/EMU1 *high* -- ARM and ETB are *disabled*
  11 # after JTAG reset until ICEpick is used to route them in.
  12 set EMU01 "-disable"
  13
  14 # With EMU0/EMU1 jumpered *low* ARM and ETB are *enabled* without
  15 # needing any ICEpick interaction.
  16 #set EMU01 "-enable"
  17
  18 source [find target/icepick.cfg]
  19
  20 # Subsidiary TAP: ARM ETB11, with scan chain for 4K of ETM trace buffer
  21 if { [info exists ETB_TAPID] } {
  22    set _ETB_TAPID $ETB_TAPID
  23 } else {
  24    set _ETB_TAPID 0x2b900f0f
  25 }
  26 jtag newtap $_CHIPNAME etb -irlen 4 -irmask 0xf -expected-id $_ETB_TAPID $EMU01
  27 jtag configure $_CHIPNAME.etb -event tap-enable \
  28         "icepick_c_tapenable $_CHIPNAME.jrc 1"
  29
  30 # Subsidiary TAP: ARM926ejs with scan chains for ARM Debug, EmbeddedICE-RT, ETM.
  31 if { [info exists CPU_TAPID] } {
  32    set _CPU_TAPID $CPU_TAPID
  33 } else {
  34    set _CPU_TAPID 0x0792602f
  35 }
  36 jtag newtap $_CHIPNAME arm -irlen 4 -irmask 0xf -expected-id $_CPU_TAPID $EMU01
  37 jtag configure $_CHIPNAME.arm -event tap-enable \
  38         "icepick_c_tapenable $_CHIPNAME.jrc 0"
  39
  40 # Primary TAP: ICEpick (JTAG route controller) and boundary scan
  41 if { [info exists JRC_TAPID] } {
  42    set _JRC_TAPID $JRC_TAPID
  43 } else {
  44    set _JRC_TAPID 0x0b83e02f
  45 }
  46 jtag newtap $_CHIPNAME jrc -irlen 6 -irmask 0x3f -expected-id $_JRC_TAPID
  47
  48 jtag configure $_CHIPNAME.jrc -event setup \
  49         "jtag tapenable $_CHIPNAME.etb; jtag tapenable $_CHIPNAME.arm"
  50
  51 ################
  52
  53 # various symbol definitions, to avoid hard-wiring addresses
  54 # and enable some sharing of DaVinci-family utility code
  55 global dm365
  56 set dm365 [ dict create ]
  57
  58 # Physical addresses for controllers and memory
  59 # (Some of these are valid for many DaVinci family chips)
  60 dict set dm365 sram0            0x00010000
  61 dict set dm365 sram1            0x00014000
  62 dict set dm365 sysbase          0x01c40000
  63 dict set dm365 pllc1            0x01c40800
  64 dict set dm365 pllc2            0x01c40c00
  65 dict set dm365 psc              0x01c41000
  66 dict set dm365 gpio             0x01c67000
  67 dict set dm365 a_emif           0x01d10000
  68 dict set dm365 a_emif_cs0       0x02000000
  69 dict set dm365 a_emif_cs1       0x04000000
  70 dict set dm365 ddr_emif         0x20000000
  71 dict set dm365 ddr              0x80000000
  72
  73 source [find target/davinci.cfg]
  74
  75 ################
  76 # GDB target: the ARM, using SRAM1 for scratch.  SRAM0 (also 16K)
  77 # and the ETB memory (4K) are other options, while trace is unused.
  78 set _TARGETNAME $_CHIPNAME.arm
  79
  80 target create $_TARGETNAME arm926ejs -chain-position $_TARGETNAME
  81
  82 # NOTE that work-area-virt presumes a Linux 2.6.30-rc2+ kernel,
  83 # and that the work area is used only with a kernel mmu context ...
  84 $_TARGETNAME configure \
  85         -work-area-virt [expr 0xfffe0000 + 0x4000] \
  86         -work-area-phys [dict get $dm365 sram1] \
  87         -work-area-size 0x4000 \
  88         -work-area-backup 0
  89
  90 # be absolutely certain the JTAG clock will work with the worst-case
  91 # CLKIN = 19.2 MHz (best case: 36 MHz) even when no bootloader turns
  92 # on the PLL and starts using it.  OK to speed up after clock setup.
  93 adapter_khz 1500
  94 $_TARGETNAME configure -event "reset-start" { adapter_khz 1500 }
  95
  96 arm7_9 fast_memory_access enable
  97 arm7_9 dcc_downloads enable
  98
  99 # trace setup
 100 etm config $_TARGETNAME 16 normal full etb
 101 etb config $_TARGETNAME $_CHIPNAME.etb