# SPDX-License-Identifier: GPL-2.0-or-later

# script for stm32wlx family

#
# stm32wl devices support both JTAG and SWD transports.
#
source [find target/swj-dp.tcl]
source [find mem_helper.tcl]

if { [info exists CHIPNAME] } {
	set _CHIPNAME $CHIPNAME
} else {
	set _CHIPNAME stm32wlx
}

if { [info exists DUAL_CORE] } {
	set $_CHIPNAME.DUAL_CORE $DUAL_CORE
	unset DUAL_CORE
} else {
	set $_CHIPNAME.DUAL_CORE 0
}

if { [info exists WKUP_CM0P] } {
	set $_CHIPNAME.WKUP_CM0P $WKUP_CM0P
	unset WKUP_CM0P
} else {
	set $_CHIPNAME.WKUP_CM0P 0
}

# Issue a warning when hla is used, and fallback to single core configuration
if { [set $_CHIPNAME.DUAL_CORE] && [using_hla] } {
	echo "Warning : hla does not support multicore debugging"
	set $_CHIPNAME.DUAL_CORE 0
	set $_CHIPNAME.WKUP_CM0P 0
}

# setup the Work-area start address and size
# Work-area is a space in RAM used for flash programming

# Memory map for known devices:
# STM32WL   x5JC   x5JB   x5J8
#   FLASH   256    128    64
#   SRAM1   32     16     0
#   SRAM2   32     32     20

# By default use 8kB
if { [info exists WORKAREASIZE] } {
	set _WORKAREASIZE $WORKAREASIZE
} else {
	set _WORKAREASIZE 0x2000
}

# Use SRAM2 as work area (some devices do not have SRAM1):
set WORKAREASTART_CM4   0x20008000
set WORKAREASTART_CM0P  [expr {$WORKAREASTART_CM4 + $_WORKAREASIZE}]

#jtag scan chain
if { [info exists CPUTAPID] } {
	set _CPUTAPID $CPUTAPID
} else {
	if { [using_jtag] } {
		set _CPUTAPID 0x6ba00477
	} else {
		# SWD IDCODE (single drop, arm)
		set _CPUTAPID 0x6ba02477
	}
}

swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu

if {[using_jtag]} {
	jtag newtap $_CHIPNAME bs -irlen 5
}

target create $_CHIPNAME.cpu0 cortex_m -endian little -dap $_CHIPNAME.dap

$_CHIPNAME.cpu0 configure -work-area-phys $WORKAREASTART_CM4 -work-area-size $_WORKAREASIZE -work-area-backup 0

flash bank $_CHIPNAME.flash.cpu0 stm32l4x 0x08000000 0 0 0 $_CHIPNAME.cpu0
flash bank $_CHIPNAME.otp.cpu0   stm32l4x 0x1fff7000 0 0 0 $_CHIPNAME.cpu0

if {![using_hla]} {
	# if srst is not fitted use SYSRESETREQ to
	# perform a soft reset
	$_CHIPNAME.cpu0 cortex_m reset_config sysresetreq
}

$_CHIPNAME.cpu0 configure -event reset-init {
	# CPU comes out of reset with MSI_ON | MSI_RDY | MSI Range 4 MHz.
	# Configure system to use MSI 24 MHz clock, compliant with VOS default Range1.
	# 2 WS compliant with VOS=Range1 and 24 MHz.
	mmw 0x58004000 0x00000102 0  ;# FLASH_ACR |= PRFTEN | 2(Latency)
	mmw 0x58000000 0x00000091 0  ;# RCC_CR = MSI_ON | MSI Range 24 MHz
	# Boost JTAG frequency
	adapter speed 4000
}

$_CHIPNAME.cpu0 configure -event reset-start {
	# Reset clock is MSI (4 MHz)
	adapter speed 500
}

$_CHIPNAME.cpu0 configure -event examine-end {
	# Enable debug during low power modes (uses more power)
	# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
	mmw 0xE0042004 0x00000007 0

	# Stop watchdog counters during halt
	# DBGMCU_APB1_FZR1 |= DBG_IWDG_STOP | DBG_WWDG_STOP
	mmw 0xE004203C 0x00001800 0

	set _CHIPNAME [stm32wlx_get_chipname]
	global $_CHIPNAME.WKUP_CM0P

	if {[set $_CHIPNAME.WKUP_CM0P]} {
		stm32wlx_wkup_cm0p
	}
}

tpiu create $_CHIPNAME.tpiu -dap $_CHIPNAME.dap -ap-num 0 -baseaddr 0xE0040000

if {[set $_CHIPNAME.DUAL_CORE]} {
	target create $_CHIPNAME.cpu1 cortex_m -endian little -dap $_CHIPNAME.dap -ap-num 1

	$_CHIPNAME.cpu0 configure -work-area-phys $WORKAREASTART_CM0P -work-area-size $_WORKAREASIZE -work-area-backup 0

	flash bank $_CHIPNAME.flash.cpu1 stm32l4x 0x08000000 0 0 0 $_CHIPNAME.cpu1
	flash bank $_CHIPNAME.otp.cpu1   stm32l4x 0x1fff7000 0 0 0 $_CHIPNAME.cpu1

	if {![using_hla]} {
		# if srst is not fitted use SYSRESETREQ to
		# perform a soft reset
		$_CHIPNAME.cpu1 cortex_m reset_config sysresetreq
	}

	proc stm32wlx_wkup_cm0p {} {
		set _CHIPNAME [stm32wlx_get_chipname]

		# enable CPU2 boot after reset and after wakeup from Stop or Standby mode
		# PWR_CR4 |= C2BOOT
		stm32wlx_mmw $_CHIPNAME.cpu0 0x5800040C 0x00008000 0
	}
}

# get _CHIPNAME from current target
proc stm32wlx_get_chipname {} {
	set t [target current]
	set sep [string last "." $t]
	if {$sep == -1} {
		return $t
	}
	return [string range $t 0 [expr {$sep - 1}]]
}

# like mrw, but with target selection
proc stm32wlx_mrw {used_target reg} {
	return [$used_target read_memory $reg 32 1]
}

# like mmw, but with target selection
proc stm32wlx_mmw {used_target reg setbits clearbits} {
	set old [stm32wlx_mrw $used_target $reg]
	set new [expr {($old & ~$clearbits) | $setbits}]
	$used_target mww $reg $new
}

# Make sure that cpu0 is selected
targets $_CHIPNAME.cpu0

# Common knowledges tells JTAG speed should be <= F_CPU/6.
# F_CPU after reset is MSI 4MHz, so use F_JTAG = 500 kHz to stay on
# the safe side.
#
# Note that there is a pretty wide band where things are
# more or less stable, see http://openocd.zylin.com/#/c/3366/
adapter speed 500

adapter srst delay 100
if {[using_jtag]} {
	jtag_ntrst_delay 100
}

reset_config srst_nogate