tcl/interface/ftdi: Add Steppenprobe open hardware interface

[openocd.git] / README

diff --git a/README b/README
index dec3673cce6ad5dc0f68e7be9bbdfdcd49fd5d0c..900324ab10717057b3c3827c6b7468c2b775790a 100644 (file)
--- a/README
+++ b/README
@@ -4,7 +4,7 @@ Welcome to OpenOCD!
 OpenOCD provides on-chip programming and debugging support with a
 layered architecture of JTAG interface and TAP support including:
 
-- (X)SVF playback to faciliate automated boundary scan and FPGA/CPLD
+- (X)SVF playback to facilitate automated boundary scan and FPGA/CPLD
   programming;
 - debug target support (e.g. ARM, MIPS): single-stepping,
   breakpoints/watchpoints, gprof profiling, etc;
@@ -42,7 +42,7 @@ e.g.:
   openocd -f interface/ftdi/jtagkey2.cfg -c "transport select jtag" \
           -f target/ti_calypso.cfg
 
-  openocd -f interface/stlink-v2-1.cfg -c "transport select hla_swd" \
+  openocd -f interface/stlink.cfg -c "transport select hla_swd" \
           -f target/stm32l0.cfg
 
 After OpenOCD startup, connect GDB with
@@ -117,17 +117,18 @@ Debug targets
 -------------
 
 ARM11, ARM7, ARM9, AVR32, Cortex-A, Cortex-R, Cortex-M, LS102x-SAP,
-Feroceon/Dragonite, DSP563xx, DSP5680xx, FA526, MIPS EJTAG, NDS32,
-XScale, Intel Quark.
+Feroceon/Dragonite, DSP563xx, DSP5680xx, EnSilica eSi-RISC, FA526, MIPS
+EJTAG, NDS32, XScale, Intel Quark.
 
 Flash drivers
 -------------
 
-ADUC702x, AT91SAM, AVR, CFI, DSP5680xx, EFM32, EM357, FM3, FM4, Kinetis,
-LPC8xx/LPC1xxx/LPC2xxx/LPC541xx, LPC2900, LPCSPIFI, Marvell QSPI,
-Milandr, NIIET, NuMicro, PIC32mx, PSoC4, SiM3x, Stellaris, STM32, STMSMI,
-STR7x, STR9x, nRF51; NAND controllers of AT91SAM9, LPC3180, LPC32xx,
-i.MX31, MXC, NUC910, Orion/Kirkwood, S3C24xx, S3C6400, XMC1xxx, XMC4xxx.
+ADUC702x, AT91SAM, ATH79, AVR, CFI, DSP5680xx, EFM32, EM357, eSi-TSMC, FM3,
+FM4, Freedom E SPI, Kinetis, LPC8xx/LPC1xxx/LPC2xxx/LPC541xx, LPC2900,
+LPCSPIFI, Marvell QSPI, Milandr, NIIET, NuMicro, PIC32mx, PSoC4, PSoC5LP,
+SiM3x, Stellaris, STM32, STMSMI, STR7x, STR9x, nRF51; NAND controllers of
+AT91SAM9, LPC3180, LPC32xx, i.MX31, MXC, NUC910, Orion/Kirkwood, S3C24xx,
+S3C6400, XMC1xxx, XMC4xxx.
 
 
 ==================
@@ -276,18 +277,22 @@ e.g. for cross-building for Windows 32-bit with MinGW on Debian:
 To make pkg-config work nicely for cross-compiling, you might need an
 additional wrapper script as described at
 
-  http://www.flameeyes.eu/autotools-mythbuster/pkgconfig/cross-compiling.html
+  https://autotools.io/pkgconfig/cross-compiling.html
 
 This is needed to tell pkg-config where to look for the target
 libraries that OpenOCD depends on. Alternatively, you can specify
 *_CFLAGS and *_LIBS environment variables directly, see "./configure
 --help" for the details.
 
+For a more or less complete script that does all this for you, see
+
+  contrib/cross-build.sh
+
 Parallel Port Dongles
 ---------------------
 
 If you want to access the parallel port using the PPDEV interface you
-have to specify both --enable-parport AND --enable-parport-ppdev, since the
+have to specify both --enable-parport AND --enable-parport-ppdev, since
 the later option is an option to the parport driver.
 
 The same is true for the --enable-parport-giveio option, you have to