doc/openocd.texi: Add documentation for bcm2835 interface

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 8f372a1a214501726db379b80c5c7bec7b7da4b3..3aee034a4a267eebd53b83c18b8888abee8b2568 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -3197,6 +3197,73 @@ configuration on exit.
 See @file{interface/raspberrypi-native.cfg} for a sample config and
 pinout.
 
+@deffn {Config Command} {bcm2835gpio_jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
+Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order).
+Must be specified to enable JTAG transport. These pins can also be specified
+individually.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_tck_num} @var{tck}
+Set TCK GPIO number. Must be specified to enable JTAG transport. Can also be
+specified using the configuration command bcm2835gpio_jtag_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_tms_num} @var{tms}
+Set TMS GPIO number. Must be specified to enable JTAG transport. Can also be
+specified using the configuration command bcm2835gpio_jtag_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_tdo_num} @var{tdo}
+Set TDO GPIO number. Must be specified to enable JTAG transport. Can also be
+specified using the configuration command bcm2835gpio_jtag_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_tdi_num} @var{tdi}
+Set TDI GPIO number. Must be specified to enable JTAG transport. Can also be
+specified using the configuration command bcm2835gpio_jtag_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_swd_nums} @var{swclk} @var{swdio}
+Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
+specified to enable SWD transport. These pins can also be specified individually.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_swclk_num} @var{swclk}
+Set SWCLK GPIO number. Must be specified to enable SWD transport. Can also be
+specified using the configuration command bcm2835gpio_swd_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_swdio_num} @var{swdio}
+Set SWDIO GPIO number. Must be specified to enable SWD transport. Can also be
+specified using the configuration command bcm2835gpio_swd_nums.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_swdio_dir_num} @var{swdio} @var{dir}
+Set SWDIO direction control pin GPIO number. If specified, this pin can be used
+to control the direction of an external buffer on the SWDIO pin (set=output
+mode, clear=input mode). If not specified, this feature is disabled.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_srst_num} @var{srst}
+Set SRST GPIO number. Must be specified to enable SRST.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_trst_num} @var{trst}
+Set TRST GPIO number. Must be specified to enable TRST.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_speed_coeffs} @var{speed_coeff} @var{speed_offset}
+Set SPEED_COEFF and SPEED_OFFSET for delay calculations. If unspecified,
+speed_coeff defaults to 113714, and speed_offset defaults to 28.
+@end deffn
+
+@deffn {Config Command} {bcm2835gpio_peripheral_base} @var{base}
+Set the peripheral base register address to access GPIOs. For the RPi1, use
+0x20000000. For RPi2 and RPi3, use 0x3F000000. For RPi4, use 0xFE000000. A full
+list can be found in the
+@uref{https://www.raspberrypi.org/documentation/hardware/raspberrypi/peripheral_addresses.md, official guide}.
+@end deffn
+
 @end deffn
 
 @deffn {Interface Driver} {imx_gpio}