-@section STR71x Script
-@cindex STR71x Script
-The following script was used with an Amontec JTAGkey and a STR710 / STR711 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 0
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-run_and_halt_time 0 30
-
-working_area 0 0x2000C000 0x4000 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str7x 0x40000000 0x00040000 0 0 0 STR71x
-@end smallexample
-
-@section STR750 Script
-@cindex STR750 Script
-The following script was used with an Amontec JTAGkey and a STR750 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 19
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-#reset_config trst_and_srst srst_pulls_trst
-reset_config trst_and_srst srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#jtag nTRST and nSRST delay
-jtag_nsrst_delay 500
-jtag_ntrst_delay 500
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-run_and_halt_time 0 30
-
-working_area 0 0x40000000 0x4000 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str7x 0x20000000 0x000040000 0 0 0 STR75x
-@end smallexample
-
-@section STR912 Script
-@cindex STR912 Script
-The following script was used with an Amontec JTAGkey and a STR912 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-jtag_speed 1
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 8 0x1 0x1 0xfe
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm966e <endianness> <reset mode> <chainpos> <variant>
-target arm966e little reset_halt 1 arm966e
-run_and_halt_time 0 30
-
-working_area 0 0x50000000 16384 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str9x 0x00000000 0x00080000 0 0 0
-@end smallexample
-
-@section STR912 comstick
-@cindex STR912 comstick Script
-The following script was used with a Hitex STR9 Comstick:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "STR9-comStick A"
-ft2232_layout comstick
-jtag_speed 1
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 8 0x1 0x1 0xfe
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm966e <endianness> <reset mode> <chainpos> <variant>
-target arm966e little reset_halt 1 arm966e
-run_and_halt_time 0 30
-
-working_area 0 0x50000000 16384 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank str9x 0x00000000 0x00080000 0 0 0
-@end smallexample
-
-@section STM32x Script
-@cindex STM32x Script
-The following script was used with an Amontec JTAGkey and a STM32x CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-jtag_speed 10
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target cortex_m3 <endianness> <reset mode> <chainpos> <variant>
-target cortex_m3 little run_and_halt 0
-run_and_halt_time 0 30
-
-working_area 0 0x20000000 16384 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank stm32x 0x08000000 0x00020000 0 0 0
-@end smallexample
-
-@section STM32x Performance Stick
-@cindex STM32x Performance Stick Script
-The following script was used with the Hitex STM32 Performance Stick
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "STM32-PerformanceStick A"
-ft2232_layout stm32stick
-jtag_speed 10
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-jtag_device 5 0x1 0x1 0x1e
-jtag_device 4 0x1 0xf 0xe
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target cortex_m3 <endianness> <reset mode> <chainpos> <variant>
-target cortex_m3 little run_and_halt 0
-run_and_halt_time 0 30
-
-working_area 0 0x20000000 16384 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank stm32x 0x08000000 0x00020000 0 0 0
-@end smallexample
-
-@section LPC2129 Script
-@cindex LPC2129 Script
-The following script was used with an wiggler PP and a LPC-2129 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface parport
-parport_port 0x378
-parport_cable wiggler
-jtag_speed 0
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
-run_and_halt_time 0 30
-
-working_area 0 0x40000000 0x4000 nobackup
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum
-@end smallexample
-
-@section LPC2148 Script
-@cindex LPC2148 Script
-The following script was used with an Amontec JTAGkey and a LPC2148 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 3
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
-run_and_halt_time 0 30
-
-working_area 0 0x40000000 0x8000 nobackup
-
-#flash configuration
-flash bank lpc2000 0x0 0x7d000 0 0 0 lpc2000_v1 14765 calc_checksum
-@end smallexample
-
-@section LPC2294 Script
-@cindex LPC2294 Script
-The following script was used with an Amontec JTAGkey and a LPC2294 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 3
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi-s_r4
-run_and_halt_time 0 30
-
-working_area 0 0x40000000 0x4000 nobackup
-
-#flash configuration
-flash bank lpc2000 0x0 0x40000 0 0 0 lpc2000_v1 14765 calc_checksum
-@end smallexample
-
-@section AT91R40008 Script
-@cindex AT91R40008 Script
-The following script was used with an Amontec JTAGkey and a AT91R40008 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 0
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-run_and_halt_time 0 30
-@end smallexample
-
-@section AT91SAM7s Script
-@cindex AT91SAM7s Script
-The following script was used with an Olimex ARM-JTAG-OCD and a AT91SAM7S64 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Olimex OpenOCD JTAG A"
-ft2232_layout olimex-jtag
-ft2232_vid_pid 0x15BA 0x0003
-jtag_speed 0
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <endianness> <reset mode> <chainpos> <variant>
-target arm7tdmi little run_and_halt 0 arm7tdmi
-run_and_halt_time 0 30
-
-# flash-options AT91
-working_area 0 0x00200000 0x4000 nobackup
-flash bank at91sam7 0 0 0 0 0
-
-# Information:
-# erase command (telnet-interface) for complete flash:
-# flash erase <num> 0 numlockbits-1 (can be seen from output of flash info 0)
-# SAM7S64 with 16 lockbits and bank 0: flash erase 0 0 15
-# set/clear NVM-Bits:
-# at91sam7 gpnvm <num> <bit> <set|clear>
-# disable locking from SAM-BA:
-# flash protect 0 0 1 off
-@end smallexample
-
-@section XSCALE IXP42x Script
-@cindex XSCALE IXP42x Script
-The following script was used with an Amontec JTAGkey-Tiny and a xscale ixp42x CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 0
-jtag_nsrst_delay 200
-jtag_ntrst_delay 200
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config srst_only srst_pulls_trst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 7 0x1 0x7f 0x7e
-
-#target configuration
-daemon_startup reset
-
-#target <type> <startup mode>
-#target arm7tdmi <reset mode> <chainpos> <endianness> <variant>
-target xscale big run_and_halt 0 IXP42x
-run_and_halt_time 0 30
-@end smallexample
-
-@section Cirrus Logic EP9301 Script
-@cindex Cirrus Logic EP9301 Script
-The following script was used with FT2232 based JTAG interfaces and a
-Cirrus Logic EP9301 processor on an Olimex CS-E9301 board.
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-
-#Olimex ARM-USB-OCD
-#ft2232_device_desc "Olimex OpenOCD JTAG"
-#ft2232_layout olimex-jtag
-#ft2232_vid_pid 0x15ba 0x0003
-
-#Amontec JTAGkey (and JTAGkey-Tiny)
-#Serial is only necessary if more than one JTAGkey is connected
-ft2232_device_desc "Amontec JTAGkey A"
-#ft2232_serial AMTJKV31
-#ft2232_serial T1P3S2W8
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-
-#wiggler/parallel port interface
-#interface parport
-#parport_port 0x378
-#parport_cable wiggler
-#jtag_speed 0
-jtag_speed 1
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#target configuration
-daemon_startup attach
-
-#target <type> <endianess> <reset mode>
-target arm920t little reset_halt 0
-working_area 0 0x80014000 0x1000 backup
-
-#flash configuration
-#flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options ...]
-flash bank cfi 0x60000000 0x1000000 2 2 0
-@end smallexample
-
-@section Hilscher netX 100 / 500 Script
-@cindex Hilscher netX 100 / 500 Script
-The following script was used with an Amontec JTAGkey and a Hilscher
-netX 500 CPU:
-@smallexample
-#daemon configuration
-telnet_port 4444
-gdb_port 3333
-
-#interface
-interface ft2232
-ft2232_device_desc "Amontec JTAGkey A"
-ft2232_layout jtagkey
-ft2232_vid_pid 0x0403 0xcff8
-jtag_speed 5
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 4 0x1 0xf 0xe
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#target configuration
-daemon_startup reset
-
-#target <type> <endianness> <startup mode> <chainpos> <variant>
-target arm926ejs little run_and_halt 0 arm926ejs
-run_and_halt_time 0 500
-@end smallexample
-
-@section Marvell/Intel PXA270 Script
-@cindex Marvell/Intel PXA270 Script
-@smallexample
-# config for Intel PXA270
-# not, as of 2007-06-22, openocd only works with the
-# libftd2xx library from ftdi. libftdi does not work.
-
-telnet_port 3333
-gdb_port 4444
-
-interface ft2232
-ft2232_layout olimex-jtag
-ft2232_vid_pid 0x15BA 0x0003
-ft2232_device_desc "Olimex OpenOCD JTAG"
-jtag_speed 0
-# set jtag_nsrst_delay to the delay introduced by your reset circuit
-# the rest of the needed delays are built into the openocd program
-jtag_nsrst_delay 260
-# set the jtag_ntrst_delay to the delay introduced by a reset circuit
-# the rest of the needed delays are built into the openocd program
-jtag_ntrst_delay 0
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst separate
-
-#jtag scan chain
-#format L IRC IRCM IDCODE (Length, IR Capture, IR Capture Mask, IDCODE)
-jtag_device 7 0x1 0x7f 0x7e
-
-#target configuration
-daemon_startup reset
-
-target xscale little reset_halt 0 pxa27x
-
-# maps to PXA internal RAM. If you are using a PXA255
-# you must initialize SDRAM or leave this option off
-working_area 0 0x5c000000 0x10000 nobackup
-
-run_and_halt_time 0 30
-
-#flash bank <driver> <base> <size> <chip_width> <bus_width>
-# works for P30 flash
-flash bank cfi 0x00000000 0x1000000 2 4 0
-@end smallexample
-
-@node GDB and Openocd
-@chapter GDB and Openocd
-@cindex GDB and Openocd
-Openocd complies with the remote gdbserver protocol, and as such can be used