flash/nor/stm32lx: use 0 base to autodetect second bank location

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 0b50c65b817767730d5dbbc3190dd2832e4eeed8..18e18b98364c91e460c3208b89f76e44fd1f4b01 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -288,12 +288,11 @@ communication between developers:
 
 @uref{https://lists.sourceforge.net/mailman/listinfo/openocd-devel}
 
-@section OpenOCD Bug Database
+@section OpenOCD Bug Tracker
 
-During the 0.4.x release cycle the OpenOCD project team began
-using Trac for its bug database:
+The OpenOCD Bug Tracker is hosted on SourceForge:
 
-@uref{https://sourceforge.net/apps/trac/openocd}
+@uref{https://sourceforge.net/p/openocd/tickets/}
 
 
 @node Debug Adapter Hardware
@@ -2585,6 +2584,11 @@ cmsis_dap_vid_pid 0xc251 0xf001 0x0d28 0x0204
 @end example
 @end deffn
 
+@deffn {Config Command} {cmsis_dap_serial} [serial]
+Specifies the @var{serial} of the CMSIS-DAP device to use.
+If not specified, serial numbers are not considered.
+@end deffn
+
 @deffn {Command} {cmsis-dap info}
 Display various device information, like hardware version, firmware version, current bus status.
 @end deffn
@@ -3100,6 +3104,11 @@ Specifies the adapter layout to use.
 The vendor ID and product ID of the device.
 @end deffn
 
+@deffn {Command} {hla_command} command
+Execute a custom adapter-specific command. The @var{command} string is
+passed as is to the underlying adapter layout handler.
+@end deffn
+
 @deffn {Config Command} {trace} source_clock_hz [output_file_path]
 Enable SWO tracing (if supported). The source clock rate for the
 trace port must be specified, this is typically the CPU clock rate. If
@@ -4834,6 +4843,7 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 
 @deffn Command {flash write_image} [erase] [unlock] filename [offset] [type]
 Write the image @file{filename} to the current target's flash bank(s).
+Only loadable sections from the image are written.
 A relocation @var{offset} may be specified, in which case it is added
 to the base address for each section in the image.
 The file [@var{type}] can be specified
@@ -5023,6 +5033,58 @@ flash bank $_FLASHNAME aduc702x 0 0 0 0 $_TARGETNAME
 @end example
 @end deffn
 
+@anchor{at91samd}
+@deffn {Flash Driver} at91samd
+@cindex at91samd
+
+@deffn Command {at91samd chip-erase}
+Issues a complete Flash erase via the Device Service Unit (DSU). This can be
+used to erase a chip back to its factory state and does not require the
+processor to be halted.
+@end deffn
+
+@deffn Command {at91samd set-security}
+Secures the Flash via the Set Security Bit (SSB) command. This prevents access
+to the Flash and can only be undone by using the chip-erase command which
+erases the Flash contents and turns off the security bit. Warning: at this
+time, openocd will not be able to communicate with a secured chip and it is
+therefore not possible to chip-erase it without using another tool.
+
+@example
+at91samd set-security enable
+@end example
+@end deffn
+
+@deffn Command {at91samd eeprom}
+Shows or sets the EEPROM emulation size configuration, stored in the User Row
+of the Flash. When setting, the EEPROM size must be specified in bytes and it
+must be one of the permitted sizes according to the datasheet. Settings are
+written immediately but only take effect on MCU reset. EEPROM emulation
+requires additional firmware support and the minumum EEPROM size may not be
+the same as the minimum that the hardware supports. Set the EEPROM size to 0
+in order to disable this feature.
+
+@example
+at91samd eeprom
+at91samd eeprom 1024
+@end example
+@end deffn
+
+@deffn Command {at91samd bootloader}
+Shows or sets the bootloader size configuration, stored in the User Row of the
+Flash. This is called the BOOTPROT region. When setting, the bootloader size
+must be specified in bytes and it must be one of the permitted sizes according
+to the datasheet. Settings are written immediately but only take effect on
+MCU reset. Setting the bootloader size to 0 disables bootloader protection.
+
+@example
+at91samd bootloader
+at91samd bootloader 16384
+@end example
+@end deffn
+
+@end deffn
+
 @anchor{at91sam3}
 @deffn {Flash Driver} at91sam3
 @cindex at91sam3
@@ -5489,17 +5551,28 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 
 @deffn {Flash Driver} stm32lx
 All members of the STM32L microcontroller families from ST Microelectronics
-include internal flash and use ARM Cortex-M3 cores.
+include internal flash and use ARM Cortex-M3 and Cortex-M0+ cores.
 The driver automatically recognizes a number of these chips using
 the chip identification register, and autoconfigures itself.
 
 Note that some devices have been found that have a flash size register that contains
 an invalid value, to workaround this issue you can override the probed value used by
-the flash driver.
+the flash driver. If you use 0 as the bank base address, it tells the
+driver to autodetect the bank location assuming you're configuring the
+second bank.
 
 @example
-flash bank $_FLASHNAME stm32lx 0 0x20000 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32lx 0x08000000 0x20000 0 0 $_TARGETNAME
 @end example
+
+Some stm32lx-specific commands are defined:
+
+@deffn Command {stm32lx mass_erase} num
+Mass erases the entire stm32lx device (all flash banks and EEPROM
+data). This is the only way to unlock a protected flash (unless RDP
+Level is 2 which can't be unlocked at all).
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
 @end deffn
 
 @deffn {Flash Driver} str7x