of the Open On-Chip Debugger (OpenOCD).
@itemize @bullet
-@item Copyright @copyright{} 2008 The OpenOCD Project
+@item Copyright @copyright{} 2008-2022 The OpenOCD Project
@item Copyright @copyright{} 2007-2008 Spencer Oliver @email{spen@@spen-soft.co.uk}
@item Copyright @copyright{} 2008-2010 Oyvind Harboe @email{oyvind.harboe@@zylin.com}
@item Copyright @copyright{} 2008 Duane Ellis @email{openocd@@duaneellis.com}
the hardware can support.
@end deffn
+@anchor{adapter gpio}
+@deffn {Config Command} {adapter gpio [ @
+ @option{tdo} | @option{tdi} | @option{tms} | @option{tck} | @option{trst} | @
+ @option{swdio} | @option{swdio_dir} | @option{swclk} | @option{srst} | @
+ @option{led} @
+ [ @
+ gpio_number | @option{-chip} chip_number | @
+ @option{-active-high} | @option{-active-low} | @
+ @option{-push-pull} | @option{-open-drain} | @option{-open-source} | @
+ @option{-pull-none} | @option{-pull-up} | @option{-pull-down} | @
+ @option{-init-inactive} | @option{-init-active} | @option{-init-input} @
+ ] ]}
+Define the GPIO mapping that the adapter will use. The following signals can be
+defined:
+
+@itemize @minus
+@item @option{tdo}, @option{tdi}, @option{tms}, @option{tck}, @option{trst}:
+JTAG transport signals
+@item @option{swdio}, @option{swclk}: SWD transport signals
+@item @option{swdio_dir}: optional swdio buffer control signal
+@item @option{srst}: system reset signal
+@item @option{led}: optional activity led
+
+@end itemize
+
+Some adapters require that the GPIO chip number is set in addition to the GPIO
+number. The configuration options enable signals to be defined as active-high or
+active-low. The output drive mode can be set to push-pull, open-drain or
+open-source. Most adapters will have to emulate open-drain or open-source drive
+modes by switching between an input and output. Input and output signals can be
+instructed to use a pull-up or pull-down resistor, assuming it is supported by
+the adaptor driver and hardware. The initial state of outputs may also be set,
+"active" state means 1 for active-high outputs and 0 for active-low outputs.
+Bidirectional signals may also be initialized as an input. If the swdio signal
+is buffered the buffer direction can be controlled with the swdio_dir signal;
+the active state means that the buffer should be set as an output with respect
+to the adapter. The command options are cumulative with later commands able to
+override settings defined by earlier ones. The two commands @command{gpio led 7
+-active-high} and @command{gpio led -chip 1 -active-low} sent sequentially are
+equivalent to issuing the single command @command{gpio led 7 -chip 1
+-active-low}. It is not permissible to set the drive mode or initial state for
+signals which are inputs. The drive mode for the srst and trst signals must be
+set with the @command{adapter reset_config} command. It is not permissible to
+set the initial state of swdio_dir as it is derived from the initial state of
+swdio. The command @command{adapter gpio} prints the current configuration for
+all GPIOs while the command @command{adapter gpio gpio_name} prints the current
+configuration for gpio_name. Not all adapters support this generic GPIO mapping,
+some require their own commands to define the GPIOs used. Adapters that support
+the generic mapping may not support all of the listed options.
+@end deffn
@deffn {Command} {adapter name}
Returns the name of the debug adapter driver being used.
peripherals' kernel drivers. The driver restores the previous
configuration on exit.
-GPIO numbers >= 32 can't be used for performance reasons.
+GPIO numbers >= 32 can't be used for performance reasons. GPIO configuration is
+handled by the generic command @ref{adapter gpio, @command{adapter gpio}}.
See @file{interface/raspberrypi-native.cfg} for a sample config and
pinout.
-@deffn {Config Command} {bcm2835gpio jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
-Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order).
-Must be specified to enable JTAG transport. These pins can also be specified
-individually.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio tck_num} @var{tck}
-Set TCK GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{bcm2835gpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio tms_num} @var{tms}
-Set TMS GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{bcm2835gpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio tdo_num} @var{tdo}
-Set TDO GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{bcm2835gpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio tdi_num} @var{tdi}
-Set TDI GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{bcm2835gpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio swd_nums} @var{swclk} @var{swdio}
-Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
-specified to enable SWD transport. These pins can also be specified individually.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio swclk_num} @var{swclk}
-Set SWCLK GPIO number. Must be specified to enable SWD transport. Can also be
-specified using the configuration command @command{bcm2835gpio swd_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio swdio_num} @var{swdio}
-Set SWDIO GPIO number. Must be specified to enable SWD transport. Can also be
-specified using the configuration command @command{bcm2835gpio swd_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio swdio_dir_num} @var{swdio} @var{dir}
-Set SWDIO direction control pin GPIO number. If specified, this pin can be used
-to control the direction of an external buffer on the SWDIO pin (set=output
-mode, clear=input mode). If not specified, this feature is disabled.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio srst_num} @var{srst}
-Set SRST GPIO number. Must be specified to enable SRST.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio trst_num} @var{trst}
-Set TRST GPIO number. Must be specified to enable TRST.
-@end deffn
-
@deffn {Config Command} {bcm2835gpio speed_coeffs} @var{speed_coeff} @var{speed_offset}
Set SPEED_COEFF and SPEED_OFFSET for delay calculations. If unspecified,
speed_coeff defaults to 113714, and speed_offset defaults to 28.
kernel memory; if /dev/gpiomem exists it will be used, otherwise /dev/mem will
be used. The driver restores the GPIO state on exit.
-All four GPIO ports are available. GPIOs numbered 0 to 31 are mapped to GPIO port
-0, GPIO numbers 32 to 63 are mapped to GPIO port 1 and so on.
-
-See @file{interface/beaglebone-swd-native.cfg} for a sample configuration file.
-
-@deffn {Config Command} {am335xgpio jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
-Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order).
-Must be specified to enable JTAG transport. These pins can also be specified
-individually.
-@end deffn
-
-@deffn {Config Command} {am335xgpio tck_num} @var{tck}
-Set TCK GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{am335xgpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {am335xgpio tms_num} @var{tms}
-Set TMS GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{am335xgpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {am335xgpio tdo_num} @var{tdo}
-Set TDO GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{am335xgpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {am335xgpio tdi_num} @var{tdi}
-Set TDI GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{am335xgpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {am335xgpio swd_nums} @var{swclk} @var{swdio}
-Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
-specified to enable SWD transport. These pins can also be specified individually.
-@end deffn
-
-@deffn {Config Command} {am335xgpio swclk_num} @var{swclk}
-Set SWCLK GPIO number. Must be specified to enable SWD transport. Can also be
-specified using the configuration command @command{am335xgpio swd_nums}.
-@end deffn
-
-@deffn {Config Command} {am335xgpio swdio_num} @var{swdio}
-Set SWDIO GPIO number. Must be specified to enable SWD transport. Can also be
-specified using the configuration command @command{am335xgpio swd_nums}.
-@end deffn
-
-@deffn {Config Command} {am335xgpio swdio_dir_num} @var{swdio_dir}
-Set SWDIO direction control pin GPIO number. If specified, this pin can be used
-to control the direction of an external buffer on the SWDIO pin. The direction
-control state can be set with the command @command{am335xgpio
-swdio_dir_output_state}. If not specified this feature is disabled.
-@end deffn
-
-@deffn {Config Command} {am335xgpio swdio_dir_output_state} @var{output_state}
-Set the state required for an external SWDIO buffer to be an output. Valid
-values are @option{on} (default) and @option{off}.
-@end deffn
-
-@deffn {Config Command} {am335xgpio srst_num} @var{srst}
-Set SRST GPIO number. Must be specified to enable SRST.
-@end deffn
-
-@deffn {Config Command} {am335xgpio trst_num} @var{trst}
-Set TRST GPIO number. Must be specified to enable TRST.
-@end deffn
-
-@deffn {Config Command} {am335xgpio led_num} @var{led}
-Set activity LED GPIO number. If not specified an activity LED is not enabled.
-@end deffn
-
-@deffn {Config Command} {am335xgpio led_on_state} @var{on_state}
-Set required logic level for the LED to be on. Valid values are @option{on}
-(default) and @option{off}.
-@end deffn
+All four GPIO ports are available. GPIO configuration is handled by the generic
+command @ref{adapter gpio, @command{adapter gpio}}.
@deffn {Config Command} {am335xgpio speed_coeffs} @var{speed_coeff} @var{speed_offset}
Set SPEED_COEFF and SPEED_OFFSET for delay calculations. If unspecified
speed_coeff defaults to 600000 and speed_offset defaults to 575.
@end deffn
-@end deffn
-
-
-@deffn {Interface Driver} {linuxgpiod}
-Linux provides userspace access to GPIO through libgpiod since Linux kernel version v4.6.
-The driver emulates either JTAG or SWD transport through bitbanging.
-
-See @file{interface/dln-2-gpiod.cfg} for a sample config.
-
-@deffn {Config Command} {linuxgpiod gpiochip} @var{chip}
-Set the GPIO chip number for all GPIOs used by linuxgpiod. If GPIOs use
-different GPIO chips then the individual GPIO configuration commands (i.e., not
-@command{linuxgpiod jtag_nums} or @command{linuxgpiod swd_nums}) can be used to
-set chip numbers independently for each GPIO.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
-Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order). Must
-be specified to enable JTAG transport. These pins can also be specified
-individually.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod tck_num} [@var{chip}] @var{tck}
-Set TCK GPIO number, and optionally TCK chip number. Must be specified to enable
-JTAG transport. Can also be specified using the configuration command
-@command{linuxgpiod jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod tms_num} [@var{chip}] @var{tms}
-Set TMS GPIO number, and optionally TMS chip number. Must be specified to enable
-JTAG transport. Can also be specified using the configuration command
-@command{linuxgpiod jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod tdo_num} [@var{chip}] @var{tdo}
-Set TDO GPIO number, and optionally TDO chip number. Must be specified to enable
-JTAG transport. Can also be specified using the configuration command
-@command{linuxgpiod jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod tdi_num} [@var{chip}] @var{tdi}
-Set TDI GPIO number, and optionally TDI chip number. Must be specified to enable
-JTAG transport. Can also be specified using the configuration command
-@command{linuxgpiod jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod trst_num} [@var{chip}] @var{trst}
-Set TRST GPIO number, and optionally TRST chip number. Must be specified to
-enable TRST.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod swd_nums} @var{swclk} @var{swdio}
-Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
-specified to enable SWD transport. These pins can also be specified
-individually.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod swclk_num} [@var{chip}] @var{swclk}
-Set SWCLK GPIO number, and optionally SWCLK chip number. Must be specified to
-enable SWD transport. Can also be specified using the configuration command
-@command{linuxgpiod swd_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod swdio_num} [@var{chip}] @var{swdio}
-Set SWDIO GPIO number, and optionally SWDIO chip number. Must be specified to
-enable SWD transport. Can also be specified using the configuration command
-@command{linuxgpiod swd_nums}.
-@end deffn
+See @file{interface/beaglebone-swd-native.cfg} for a sample configuration file.
-@deffn {Config Command} {linuxgpiod swdio_dir_num} [@var{chip}] @var{swdio_dir}
-Set SWDIO direction control GPIO number, and optionally SWDIO direction control
-chip number. If specified, this GPIO can be used to control the direction of an
-external buffer connected to the SWDIO GPIO (set=output mode, clear=input mode).
@end deffn
-@deffn {Config Command} {linuxgpiod srst_num} [@var{chip}] @var{srst}
-Set SRST GPIO number, and optionally SRST chip number. Must be specified to
-enable SRST.
-@end deffn
-@deffn {Config Command} {linuxgpiod led_num} [@var{chip}] @var{led}
-Set activity LED GPIO number, and optionally activity LED chip number. If not
-specified an activity LED is not enabled.
-@end deffn
+@deffn {Interface Driver} {linuxgpiod}
+Linux provides userspace access to GPIO through libgpiod since Linux kernel
+version v4.6. The driver emulates either JTAG or SWD transport through
+bitbanging. There are no driver-specific commands, all GPIO configuration is
+handled by the generic command @ref{adapter gpio, @command{adapter gpio}}. This
+driver supports the resistor pull options provided by the @command{adapter gpio}
+command but the underlying hardware may not be able to support them.
+See @file{interface/dln-2-gpiod.cfg} for a sample configuration file.
@end deffn
Disabled by default
@end deffn
+@deffn {Config Command} {$dap_name nu_npcx_quirks} [@option{enable}]
+Set/get quirks mode for Nuvoton NPCX/NPCD MCU families
+Disabled by default
+@end deffn
@node CPU Configuration
@chapter CPU Configuration
@item @code{testee} -- a dummy target for cases without a real CPU, e.g. CPLD.
@item @code{xscale} -- this is actually an architecture,
not a CPU type. It is based on the ARMv5 architecture.
+@item @code{xtensa} -- this is a generic Cadence/Tensilica Xtensa core.
@end itemize
@end deffn
@anchor{rtostype}
@item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
-@var{rtos_type} can be one of @option{auto}, @option{eCos},
+@var{rtos_type} can be one of @option{auto}, @option{none}, @option{eCos},
@option{ThreadX}, @option{FreeRTOS}, @option{linux}, @option{ChibiOS},
@option{embKernel}, @option{mqx}, @option{uCOS-III}, @option{nuttx},
@option{RIOT}, @option{Zephyr}
@end example
@end deffn
+@deffn {Flash Driver} {rsl10}
+Supports Onsemi RSL10 microcontroller flash memory. Uses functions
+stored in ROM to control flash memory interface.
+
+@example
+flash bank $_FLASHNAME rsl10 $_FLASHBASE $_FLASHSIZE 0 0 $_TARGETNAME
+@end example
+
+@deffn {Command} {rsl10 lock} key1 key2 key3 key4
+Writes @var{key1 key2 key3 key4} words to @var{0x81044 0x81048 0x8104c
+0x8050}. Locks debug port by writing @var{0x4C6F634B} to @var{0x81040}.
+
+To unlock use the @command{rsl10 unlock key1 key2 key3 key4} command.
+@end deffn
+
+@deffn {Command} {rsl10 unlock} key1 key2 key3 key4
+Unlocks debug port, by writing @var{key1 key2 key3 key4} words to
+registers through DAP, and clears @var{0x81040} address in flash to 0x1.
+@end deffn
+
+@deffn {Command} {rsl10 mass_erase}
+Erases all unprotected flash sectors.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} {sim3x}
All members of the SiM3 microcontroller family from Silicon Laboratories
include internal flash and use ARM Cortex-M3 cores. It supports both JTAG
protocol SWIM, @pxref{swimtransport,,SWIM}.
@section Xtensa Architecture
-Xtensa processors are based on a modular, highly flexible 32-bit RISC architecture
-that can easily scale from a tiny, cache-less controller or task engine to a high-performance
-SIMD/VLIW DSP provided by Cadence.
-@url{https://www.cadence.com/en_US/home/tools/ip/tensilica-ip/tensilica-xtensa-controllers-and-extensible-processors.html}.
-OpenOCD supports generic Xtensa processors implementation which can be customized by
-simply providing vendor-specific core configuration which controls every configurable
+Xtensa is a highly-customizable, user-extensible microprocessor and DSP
+architecture for complex embedded systems provided by Cadence Design
+Systems, Inc. See the
+@uref{https://www.cadence.com/en_US/home/tools/ip/tensilica-ip.html, Tensilica IP}
+website for additional information and documentation.
+
+OpenOCD supports generic Xtensa processor implementations which can be customized by
+providing a core-specific configuration file which describes every enabled
Xtensa architecture option, e.g. number of address registers, exceptions, reduced
-size instructions support, memory banks configuration etc. Also OpenOCD supports SMP
-configurations for Xtensa processors with any number of cores and allows to configure
-their debug signals interconnection (so-called "break/stall networks") which control how
-debug signals are distributed among cores. Xtensa "break networks" are compatible with
-ARM's Cross Trigger Interface (CTI). For debugging code on Xtensa chips OpenOCD
-uses JTAG protocol. Currently OpenOCD implements several Epsressif Xtensa-based chips of
+size instructions support, memory banks configuration etc. OpenOCD also supports SMP
+configurations for Xtensa processors with any number of cores and allows configuring
+their debug interconnect (termed "break/stall networks"), which control how debug
+signals are distributed among cores. Xtensa "break networks" are compatible with
+ARM's Cross Trigger Interface (CTI). OpenOCD implements both generic Xtensa targets
+as well as several Espressif Xtensa-based chips from the
@uref{https://www.espressif.com/en/products/socs, ESP32 family}.
-@subsection General Xtensa Commands
+OCD sessions for Xtensa processor and DSP targets are accessed via the Xtensa
+Debug Module (XDM), which provides external connectivity either through a
+traditional JTAG interface or an ARM DAP interface. If used, the DAP interface
+can control Xtensa targets through JTAG or SWD probes.
+
+@subsection Xtensa Core Configuration
+
+Due to the high level of configurability in Xtensa cores, the Xtensa target
+configuration comprises two categories:
+
+@enumerate
+@item Base Xtensa support common to all core configurations, and
+@item Core-specific support as configured for individual cores.
+@end enumerate
+
+All common Xtensa support is built into the OpenOCD Xtensa target layer and
+is enabled through a combination of TCL scripts: the target-specific
+@file{target/xtensa.cfg} and a board-specific @file{board/xtensa-*.cfg},
+similar to other target architectures.
+
+Importantly, core-specific configuration information must be provided by
+the user, and takes the form of an @file{xtensa-core-XXX.cfg} TCL script that
+defines the core's configurable features through a series of Xtensa
+configuration commands (detailed below).
+
+This core-specific @file{xtensa-core-XXX.cfg} file is typically either:
+
+@itemize @bullet
+@item Located within the Xtensa core configuration build as
+@file{src/config/xtensa-core-openocd.cfg}, or
+@item Generated by running the command @code{xt-gdb --dump-oocd-config}
+from the Xtensa processor tool-chain's command-line tools.
+@end itemize
+
+NOTE: @file{xtensa-core-XXX.cfg} must match the target Xtensa hardware
+connected to OpenOCD.
+
+Some example Xtensa configurations are bundled with OpenOCD for reference:
+@itemize @bullet
+@item Cadence Palladium VDebug emulation target. The user can combine their
+@file{xtensa-core-XXX.cfg} with the provided
+@file{board/xtensa-palladium-vdebug.cfg} to debug an emulated Xtensa RTL design.
+@item NXP MIMXRT685-EVK evaluation kit. The relevant configuration files are
+@file{board/xtensa-rt685-jlink.cfg} and @file{board/xtensa-core-nxp_rt600.cfg}.
+Additional information is provided by
+@uref{https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt600-evaluation-kit:MIMXRT685-EVK,
+NXP}.
+@end itemize
+
+@subsection Xtensa Configuration Commands
+
+@deffn {Command} {xtensa xtdef} (@option{LX}|@option{NX})
+Configure the Xtensa target architecture. Currently, Xtensa support is limited
+to LX6, LX7, and NX cores.
+@end deffn
+
+@deffn {Command} {xtensa xtopt} option value
+Configure Xtensa target options that are relevant to the debug subsystem.
+@var{option} is one of: @option{arnum}, @option{windowed},
+@option{cpenable}, @option{exceptions}, @option{intnum}, @option{hipriints},
+@option{excmlevel}, @option{intlevels}, @option{debuglevel},
+@option{ibreaknum}, or @option{dbreaknum}. @var{value} is an integer with
+the exact range determined by each particular option.
+
+NOTE: Some options are specific to Xtensa LX or Xtensa NX architecture, while
+others may be common to both but have different valid ranges.
+@end deffn
+
+@deffn {Command} {xtensa xtmem} (@option{iram}|@option{dram}|@option{sram}|@option{irom}|@option{drom}|@option{srom}) baseaddr bytes
+Configure Xtensa target memory. Memory type determines access rights,
+where RAMs are read/write while ROMs are read-only. @var{baseaddr} and
+@var{bytes} are both integers, typically hexadecimal and decimal, respectively.
+@end deffn
+
+@deffn {Command} {xtensa xtmem} (@option{icache}|@option{dcache}) linebytes cachebytes ways [writeback]
+Configure Xtensa processor cache. All parameters are required except for
+the optional @option{writeback} parameter; all are integers.
+@end deffn
+
+@deffn {Command} {xtensa xtmpu} numfgseg minsegsz lockable execonly
+Configure an Xtensa Memory Protection Unit (MPU). MPUs can restrict access
+and/or control cacheability of specific address ranges, but are lighter-weight
+than a full traditional MMU. All parameters are required; all are integers.
+@end deffn
+
+@deffn {Command} {xtensa xtmmu} numirefillentries numdrefillentries
+(Xtensa-LX only) Configure an Xtensa Memory Management Unit (MMU). Both
+parameters are required; both are integers.
+@end deffn
+
+@deffn {Command} {xtensa xtregs} numregs
+Configure the total number of registers for the Xtensa core. Configuration
+logic expects to subsequently process this number of @code{xtensa xtreg}
+definitions. @var{numregs} is an integer.
+@end deffn
+
+@deffn {Command} {xtensa xtregfmt} (@option{sparse}|@option{contiguous}) [general]
+Configure the type of register map used by GDB to access the Xtensa core.
+Generic Xtensa tools (e.g. xt-gdb) require @option{sparse} mapping (default) while
+Espressif tools expect @option{contiguous} mapping. Contiguous mapping takes an
+additional, optional integer parameter @option{numgregs}, which specifies the number
+of general registers used in handling g/G packets.
+@end deffn
+
+@deffn {Command} {xtensa xtreg} name offset
+Configure an Xtensa core register. All core registers are 32 bits wide,
+while TIE and user registers may have variable widths. @var{name} is a
+character string identifier while @var{offset} is a hexadecimal integer.
+@end deffn
+
+@subsection Xtensa Operation Commands
+
+@deffn {Command} {xtensa maskisr} (@option{on}|@option{off})
+(Xtensa-LX only) Mask or unmask Xtensa interrupts during instruction step.
+When masked, an interrupt that occurs during a step operation is handled and
+its ISR is executed, with the user's debug session returning after potentially
+executing many instructions. When unmasked, a triggered interrupt will result
+in execution progressing the requested number of instructions into the relevant
+vector/ISR code.
+@end deffn
@deffn {Command} {xtensa set_permissive} (0|1)
By default accessing memory beyond defined regions is forbidden. This commnd controls memory access address check.
When set to (1), skips access controls and address range check before read/write memory.
@end deffn
-@deffn {Command} {xtensa maskisr} (on|off)
-Selects whether interrupts will be disabled during stepping over single instruction. The default configuration is (off).
-@end deffn
-
@deffn {Command} {xtensa smpbreak} [none|breakinout|runstall] | [BreakIn] [BreakOut] [RunStallIn] [DebugModeOut]
Configures debug signals connection ("break network") for currently selected core.
@itemize @bullet
@end itemize
@end deffn
+@deffn {Command} {xtensa exe} <ascii-encoded hexadecimal instruction bytes>
+Execute arbitrary instruction(s) provided as an ascii string. The string represents an integer
+number of instruction bytes, thus its length must be even.
+@end deffn
+
+@subsection Xtensa Performance Monitor Configuration
+
@deffn {Command} {xtensa perfmon_enable} <counter_id> <select> [mask] [kernelcnt] [tracelevel]
Enable and start performance counter.
@itemize @bullet
Dump performance counter value. If no argument specified, dumps all counters.
@end deffn
+@subsection Xtensa Trace Configuration
+
@deffn {Command} {xtensa tracestart} [pc <pcval>/[<maskbitcount>]] [after <n> [ins|words]]
Set up and start a HW trace. Optionally set PC address range to trigger tracing stop when reached during program execution.
This command also allows to specify the amount of data to capture after stop trigger activation.
@item @option{Zephyr}
@end itemize
+At any time, it's possible to drop the selected RTOS using:
+@example
+$_TARGETNAME configure -rtos none
+@end example
+
Before an RTOS can be detected, it must export certain symbols; otherwise, it cannot
be used by OpenOCD. Below is a list of the required symbols for each supported RTOS.
Code Review / openocd.git / blobdiff