of the Open On-Chip Debugger (OpenOCD).
@itemize @bullet
-@item Copyright @copyright{} 2008 The OpenOCD Project
+@item Copyright @copyright{} 2008-2022 The OpenOCD Project
@item Copyright @copyright{} 2007-2008 Spencer Oliver @email{spen@@spen-soft.co.uk}
@item Copyright @copyright{} 2008-2010 Oyvind Harboe @email{oyvind.harboe@@zylin.com}
@item Copyright @copyright{} 2008 Duane Ellis @email{openocd@@duaneellis.com}
peripherals' kernel drivers. The driver restores the previous
configuration on exit.
-GPIO numbers >= 32 can't be used for performance reasons.
+GPIO numbers >= 32 can't be used for performance reasons. GPIO configuration is
+handled by the generic command @ref{adapter gpio, @command{adapter gpio}}.
See @file{interface/raspberrypi-native.cfg} for a sample config and
pinout.
-@deffn {Config Command} {bcm2835gpio jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
-Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order).
-Must be specified to enable JTAG transport. These pins can also be specified
-individually.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio tck_num} @var{tck}
-Set TCK GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{bcm2835gpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio tms_num} @var{tms}
-Set TMS GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{bcm2835gpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio tdo_num} @var{tdo}
-Set TDO GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{bcm2835gpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio tdi_num} @var{tdi}
-Set TDI GPIO number. Must be specified to enable JTAG transport. Can also be
-specified using the configuration command @command{bcm2835gpio jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio swd_nums} @var{swclk} @var{swdio}
-Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
-specified to enable SWD transport. These pins can also be specified individually.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio swclk_num} @var{swclk}
-Set SWCLK GPIO number. Must be specified to enable SWD transport. Can also be
-specified using the configuration command @command{bcm2835gpio swd_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio swdio_num} @var{swdio}
-Set SWDIO GPIO number. Must be specified to enable SWD transport. Can also be
-specified using the configuration command @command{bcm2835gpio swd_nums}.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio swdio_dir_num} @var{swdio} @var{dir}
-Set SWDIO direction control pin GPIO number. If specified, this pin can be used
-to control the direction of an external buffer on the SWDIO pin (set=output
-mode, clear=input mode). If not specified, this feature is disabled.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio srst_num} @var{srst}
-Set SRST GPIO number. Must be specified to enable SRST.
-@end deffn
-
-@deffn {Config Command} {bcm2835gpio trst_num} @var{trst}
-Set TRST GPIO number. Must be specified to enable TRST.
-@end deffn
-
@deffn {Config Command} {bcm2835gpio speed_coeffs} @var{speed_coeff} @var{speed_offset}
Set SPEED_COEFF and SPEED_OFFSET for delay calculations. If unspecified,
speed_coeff defaults to 113714, and speed_offset defaults to 28.
@deffn {Interface Driver} {linuxgpiod}
-Linux provides userspace access to GPIO through libgpiod since Linux kernel version v4.6.
-The driver emulates either JTAG or SWD transport through bitbanging.
-
-See @file{interface/dln-2-gpiod.cfg} for a sample config.
-
-@deffn {Config Command} {linuxgpiod gpiochip} @var{chip}
-Set the GPIO chip number for all GPIOs used by linuxgpiod. If GPIOs use
-different GPIO chips then the individual GPIO configuration commands (i.e., not
-@command{linuxgpiod jtag_nums} or @command{linuxgpiod swd_nums}) can be used to
-set chip numbers independently for each GPIO.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
-Set JTAG transport GPIO numbers for TCK, TMS, TDI, and TDO (in that order). Must
-be specified to enable JTAG transport. These pins can also be specified
-individually.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod tck_num} [@var{chip}] @var{tck}
-Set TCK GPIO number, and optionally TCK chip number. Must be specified to enable
-JTAG transport. Can also be specified using the configuration command
-@command{linuxgpiod jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod tms_num} [@var{chip}] @var{tms}
-Set TMS GPIO number, and optionally TMS chip number. Must be specified to enable
-JTAG transport. Can also be specified using the configuration command
-@command{linuxgpiod jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod tdo_num} [@var{chip}] @var{tdo}
-Set TDO GPIO number, and optionally TDO chip number. Must be specified to enable
-JTAG transport. Can also be specified using the configuration command
-@command{linuxgpiod jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod tdi_num} [@var{chip}] @var{tdi}
-Set TDI GPIO number, and optionally TDI chip number. Must be specified to enable
-JTAG transport. Can also be specified using the configuration command
-@command{linuxgpiod jtag_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod trst_num} [@var{chip}] @var{trst}
-Set TRST GPIO number, and optionally TRST chip number. Must be specified to
-enable TRST.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod swd_nums} @var{swclk} @var{swdio}
-Set SWD transport GPIO numbers for SWCLK and SWDIO (in that order). Must be
-specified to enable SWD transport. These pins can also be specified
-individually.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod swclk_num} [@var{chip}] @var{swclk}
-Set SWCLK GPIO number, and optionally SWCLK chip number. Must be specified to
-enable SWD transport. Can also be specified using the configuration command
-@command{linuxgpiod swd_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod swdio_num} [@var{chip}] @var{swdio}
-Set SWDIO GPIO number, and optionally SWDIO chip number. Must be specified to
-enable SWD transport. Can also be specified using the configuration command
-@command{linuxgpiod swd_nums}.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod swdio_dir_num} [@var{chip}] @var{swdio_dir}
-Set SWDIO direction control GPIO number, and optionally SWDIO direction control
-chip number. If specified, this GPIO can be used to control the direction of an
-external buffer connected to the SWDIO GPIO (set=output mode, clear=input mode).
-@end deffn
-
-@deffn {Config Command} {linuxgpiod srst_num} [@var{chip}] @var{srst}
-Set SRST GPIO number, and optionally SRST chip number. Must be specified to
-enable SRST.
-@end deffn
-
-@deffn {Config Command} {linuxgpiod led_num} [@var{chip}] @var{led}
-Set activity LED GPIO number, and optionally activity LED chip number. If not
-specified an activity LED is not enabled.
-@end deffn
+Linux provides userspace access to GPIO through libgpiod since Linux kernel
+version v4.6. The driver emulates either JTAG or SWD transport through
+bitbanging. There are no driver-specific commands, all GPIO configuration is
+handled by the generic command @ref{adapter gpio, @command{adapter gpio}}. This
+driver supports the resistor pull options provided by the @command{adapter gpio}
+command but the underlying hardware may not be able to support them.
+See @file{interface/dln-2-gpiod.cfg} for a sample configuration file.
@end deffn
@item @code{testee} -- a dummy target for cases without a real CPU, e.g. CPLD.
@item @code{xscale} -- this is actually an architecture,
not a CPU type. It is based on the ARMv5 architecture.
+@item @code{xtensa} -- this is a generic Cadence/Tensilica Xtensa core.
@end itemize
@end deffn
@end example
@end deffn
+@deffn {Flash Driver} {rsl10}
+Supports Onsemi RSL10 microcontroller flash memory. Uses functions
+stored in ROM to control flash memory interface.
+
+@example
+flash bank $_FLASHNAME rsl10 $_FLASHBASE $_FLASHSIZE 0 0 $_TARGETNAME
+@end example
+
+@deffn {Command} {rsl10 lock} key1 key2 key3 key4
+Writes @var{key1 key2 key3 key4} words to @var{0x81044 0x81048 0x8104c
+0x8050}. Locks debug port by writing @var{0x4C6F634B} to @var{0x81040}.
+
+To unlock use the @command{rsl10 unlock key1 key2 key3 key4} command.
+@end deffn
+
+@deffn {Command} {rsl10 unlock} key1 key2 key3 key4
+Unlocks debug port, by writing @var{key1 key2 key3 key4} words to
+registers through DAP, and clears @var{0x81040} address in flash to 0x1.
+@end deffn
+
+@deffn {Command} {rsl10 mass_erase}
+Erases all unprotected flash sectors.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} {sim3x}
All members of the SiM3 microcontroller family from Silicon Laboratories
include internal flash and use ARM Cortex-M3 cores. It supports both JTAG
protocol SWIM, @pxref{swimtransport,,SWIM}.
@section Xtensa Architecture
-Xtensa processors are based on a modular, highly flexible 32-bit RISC architecture
-that can easily scale from a tiny, cache-less controller or task engine to a high-performance
-SIMD/VLIW DSP provided by Cadence.
-@url{https://www.cadence.com/en_US/home/tools/ip/tensilica-ip/tensilica-xtensa-controllers-and-extensible-processors.html}.
-OpenOCD supports generic Xtensa processors implementation which can be customized by
-simply providing vendor-specific core configuration which controls every configurable
+Xtensa is a highly-customizable, user-extensible microprocessor and DSP
+architecture for complex embedded systems provided by Cadence Design
+Systems, Inc. See the
+@uref{https://www.cadence.com/en_US/home/tools/ip/tensilica-ip.html, Tensilica IP}
+website for additional information and documentation.
+
+OpenOCD supports generic Xtensa processor implementations which can be customized by
+providing a core-specific configuration file which describes every enabled
Xtensa architecture option, e.g. number of address registers, exceptions, reduced
-size instructions support, memory banks configuration etc. Also OpenOCD supports SMP
-configurations for Xtensa processors with any number of cores and allows to configure
-their debug signals interconnection (so-called "break/stall networks") which control how
-debug signals are distributed among cores. Xtensa "break networks" are compatible with
-ARM's Cross Trigger Interface (CTI). For debugging code on Xtensa chips OpenOCD
-uses JTAG protocol. Currently OpenOCD implements several Epsressif Xtensa-based chips of
+size instructions support, memory banks configuration etc. OpenOCD also supports SMP
+configurations for Xtensa processors with any number of cores and allows configuring
+their debug interconnect (termed "break/stall networks"), which control how debug
+signals are distributed among cores. Xtensa "break networks" are compatible with
+ARM's Cross Trigger Interface (CTI). OpenOCD implements both generic Xtensa targets
+as well as several Espressif Xtensa-based chips from the
@uref{https://www.espressif.com/en/products/socs, ESP32 family}.
-@subsection General Xtensa Commands
+OCD sessions for Xtensa processor and DSP targets are accessed via the Xtensa
+Debug Module (XDM), which provides external connectivity either through a
+traditional JTAG interface or an ARM DAP interface. If used, the DAP interface
+can control Xtensa targets through JTAG or SWD probes.
+
+@subsection Xtensa Core Configuration
+
+Due to the high level of configurability in Xtensa cores, the Xtensa target
+configuration comprises two categories:
+
+@enumerate
+@item Base Xtensa support common to all core configurations, and
+@item Core-specific support as configured for individual cores.
+@end enumerate
+
+All common Xtensa support is built into the OpenOCD Xtensa target layer and
+is enabled through a combination of TCL scripts: the target-specific
+@file{target/xtensa.cfg} and a board-specific @file{board/xtensa-*.cfg},
+similar to other target architectures.
+
+Importantly, core-specific configuration information must be provided by
+the user, and takes the form of an @file{xtensa-core-XXX.cfg} TCL script that
+defines the core's configurable features through a series of Xtensa
+configuration commands (detailed below).
+
+This core-specific @file{xtensa-core-XXX.cfg} file is typically either:
+
+@itemize @bullet
+@item Located within the Xtensa core configuration build as
+@file{src/config/xtensa-core-openocd.cfg}, or
+@item Generated by running the command @code{xt-gdb --dump-oocd-config}
+from the Xtensa processor tool-chain's command-line tools.
+@end itemize
+
+NOTE: @file{xtensa-core-XXX.cfg} must match the target Xtensa hardware
+connected to OpenOCD.
+
+Some example Xtensa configurations are bundled with OpenOCD for reference:
+@itemize @bullet
+@item Cadence Palladium VDebug emulation target. The user can combine their
+@file{xtensa-core-XXX.cfg} with the provided
+@file{board/xtensa-palladium-vdebug.cfg} to debug an emulated Xtensa RTL design.
+@item NXP MIMXRT685-EVK evaluation kit. The relevant configuration files are
+@file{board/xtensa-rt685-jlink.cfg} and @file{board/xtensa-core-nxp_rt600.cfg}.
+Additional information is provided by
+@uref{https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/i-mx-rt600-evaluation-kit:MIMXRT685-EVK,
+NXP}.
+@end itemize
+
+@subsection Xtensa Configuration Commands
+
+@deffn {Command} {xtensa xtdef} (@option{LX}|@option{NX})
+Configure the Xtensa target architecture. Currently, Xtensa support is limited
+to LX6, LX7, and NX cores.
+@end deffn
+
+@deffn {Command} {xtensa xtopt} option value
+Configure Xtensa target options that are relevant to the debug subsystem.
+@var{option} is one of: @option{arnum}, @option{windowed},
+@option{cpenable}, @option{exceptions}, @option{intnum}, @option{hipriints},
+@option{excmlevel}, @option{intlevels}, @option{debuglevel},
+@option{ibreaknum}, or @option{dbreaknum}. @var{value} is an integer with
+the exact range determined by each particular option.
+
+NOTE: Some options are specific to Xtensa LX or Xtensa NX architecture, while
+others may be common to both but have different valid ranges.
+@end deffn
+
+@deffn {Command} {xtensa xtmem} (@option{iram}|@option{dram}|@option{sram}|@option{irom}|@option{drom}|@option{srom}) baseaddr bytes
+Configure Xtensa target memory. Memory type determines access rights,
+where RAMs are read/write while ROMs are read-only. @var{baseaddr} and
+@var{bytes} are both integers, typically hexadecimal and decimal, respectively.
+@end deffn
+
+@deffn {Command} {xtensa xtmem} (@option{icache}|@option{dcache}) linebytes cachebytes ways [writeback]
+Configure Xtensa processor cache. All parameters are required except for
+the optional @option{writeback} parameter; all are integers.
+@end deffn
+
+@deffn {Command} {xtensa xtmpu} numfgseg minsegsz lockable execonly
+Configure an Xtensa Memory Protection Unit (MPU). MPUs can restrict access
+and/or control cacheability of specific address ranges, but are lighter-weight
+than a full traditional MMU. All parameters are required; all are integers.
+@end deffn
+
+@deffn {Command} {xtensa xtmmu} numirefillentries numdrefillentries
+(Xtensa-LX only) Configure an Xtensa Memory Management Unit (MMU). Both
+parameters are required; both are integers.
+@end deffn
+
+@deffn {Command} {xtensa xtregs} numregs
+Configure the total number of registers for the Xtensa core. Configuration
+logic expects to subsequently process this number of @code{xtensa xtreg}
+definitions. @var{numregs} is an integer.
+@end deffn
+
+@deffn {Command} {xtensa xtregfmt} (@option{sparse}|@option{contiguous}) [general]
+Configure the type of register map used by GDB to access the Xtensa core.
+Generic Xtensa tools (e.g. xt-gdb) require @option{sparse} mapping (default) while
+Espressif tools expect @option{contiguous} mapping. Contiguous mapping takes an
+additional, optional integer parameter @option{numgregs}, which specifies the number
+of general registers used in handling g/G packets.
+@end deffn
+
+@deffn {Command} {xtensa xtreg} name offset
+Configure an Xtensa core register. All core registers are 32 bits wide,
+while TIE and user registers may have variable widths. @var{name} is a
+character string identifier while @var{offset} is a hexadecimal integer.
+@end deffn
+
+@subsection Xtensa Operation Commands
+
+@deffn {Command} {xtensa maskisr} (@option{on}|@option{off})
+(Xtensa-LX only) Mask or unmask Xtensa interrupts during instruction step.
+When masked, an interrupt that occurs during a step operation is handled and
+its ISR is executed, with the user's debug session returning after potentially
+executing many instructions. When unmasked, a triggered interrupt will result
+in execution progressing the requested number of instructions into the relevant
+vector/ISR code.
+@end deffn
@deffn {Command} {xtensa set_permissive} (0|1)
By default accessing memory beyond defined regions is forbidden. This commnd controls memory access address check.
When set to (1), skips access controls and address range check before read/write memory.
@end deffn
-@deffn {Command} {xtensa maskisr} (on|off)
-Selects whether interrupts will be disabled during stepping over single instruction. The default configuration is (off).
-@end deffn
-
@deffn {Command} {xtensa smpbreak} [none|breakinout|runstall] | [BreakIn] [BreakOut] [RunStallIn] [DebugModeOut]
Configures debug signals connection ("break network") for currently selected core.
@itemize @bullet
@end itemize
@end deffn
+@deffn {Command} {xtensa exe} <ascii-encoded hexadecimal instruction bytes>
+Execute arbitrary instruction(s) provided as an ascii string. The string represents an integer
+number of instruction bytes, thus its length must be even.
+@end deffn
+
+@subsection Xtensa Performance Monitor Configuration
+
@deffn {Command} {xtensa perfmon_enable} <counter_id> <select> [mask] [kernelcnt] [tracelevel]
Enable and start performance counter.
@itemize @bullet
Dump performance counter value. If no argument specified, dumps all counters.
@end deffn
+@subsection Xtensa Trace Configuration
+
@deffn {Command} {xtensa tracestart} [pc <pcval>/[<maskbitcount>]] [after <n> [ins|words]]
Set up and start a HW trace. Optionally set PC address range to trigger tracing stop when reached during program execution.
This command also allows to specify the amount of data to capture after stop trigger activation.
Code Review / openocd.git / blobdiff