target/etb: Use 'bool' data type

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 3c1e33d6d886934848bfa71cfe7e85e52183c444..2e04182b3c7eae7eb034e40da9da43e40f7a8a18 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -2368,7 +2368,8 @@ the hardware can support.
 Returns the name of the debug adapter driver being used.
 @end deffn
 
-@deffn Command {adapter usb location} <bus>:<port>[.<port>]...
+@anchor{adapter_usb_location}
+@deffn Command {adapter usb location} <bus>-<port>[.<port>]...
 Specifies the physical USB port of the adapter to use. The path
 roots at @var{bus} and walks down the physical ports, with each
 @var{port} option specifying a deeper level in the bus topology, the last
@@ -2510,7 +2511,10 @@ If not specified, serial numbers are not considered.
 and are not restricted to containing only decimal digits.)
 @end deffn
 
-@deffn {Config Command} {ftdi_location} <bus>:<port>[,<port>]...
+@deffn {Config Command} {ftdi_location} <bus>-<port>[.<port>]...
+@emph{DEPRECATED -- avoid using this.
+Use the @xref{adapter_usb_location, adapter usb location} command instead.}
+
 Specifies the physical USB port of the adapter to use. The path
 roots at @var{bus} and walks down the physical ports, with each
 @var{port} option specifying a deeper level in the bus topology, the last
@@ -6641,6 +6645,17 @@ the chip identification register, and autoconfigures itself.
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
 @end example
 
+If you use OTP (One-Time Programmable) memory define it as a second bank
+as per the following example.
+@example
+flash bank $_FLASHNAME stm32f2x 0x1FFF7800 0 0 0 $_TARGETNAME
+@end example
+
+@deffn Command {stm32f2x otp } num (@option{enable}|@option{disable}|@option{show})
+Enables or disables OTP write commands for bank @var{num}.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
 Note that some devices have been found that have a flash size register that contains
 an invalid value, to workaround this issue you can override the probed value used by
 the flash driver.
@@ -9330,6 +9345,14 @@ be copied to an in-memory buffer identified by the @option{address} and
 @option{size} options using DMA.
 @end deffn
 
+@deffn Command {$target_name catch_exc} [@option{off}|@option{sec_el1}|@option{sec_el3}|@option{nsec_el1}|@option{nsec_el2}]+
+Cause @command{$target_name} to halt when an exception is taken. Any combination of
+Secure (sec) EL1/EL3 or Non-Secure (nsec) EL1/EL2 is valid. The target
+@command{$target_name} will halt before taking the exception. In order to resume
+the target, the exception catch must be disabled again with @command{$target_name catch_exc off}.
+Issuing the command without options prints the current configuration.
+@end deffn
+
 @section Intel Architecture
 
 Intel Quark X10xx is the first product in the Quark family of SoCs. It is an IA-32