-\input texinfo @c -*-texinfo-*-
+\input texinfo @c -*-texinfo-*-
@c %**start of header
@setfilename openocd.info
-@settitle Open On-Chip Debugger (OpenOCD)
+@settitle OpenOCD User's Guide
@dircategory Development
@direntry
-@paragraphindent 0
-* OpenOCD: (openocd). Open On-Chip Debugger.
+* OpenOCD: (openocd). OpenOCD User's Guide
@end direntry
+@paragraphindent 0
@c %**end of header
@include version.texi
@copying
+This User's Guide documents
+release @value{VERSION},
+dated @value{UPDATED},
+of the Open On-Chip Debugger (OpenOCD).
+
@itemize @bullet
@item Copyright @copyright{} 2008 The OpenOCD Project
@item Copyright @copyright{} 2007-2008 Spencer Oliver @email{spen@@spen-soft.co.uk}
@end copying
@titlepage
-@title Open On-Chip Debugger (OpenOCD)
-@subtitle Edition @value{EDITION} for OpenOCD version @value{VERSION}
+@titlefont{@emph{Open On-Chip Debugger:}}
+@sp 1
+@title OpenOCD User's Guide
+@subtitle for release @value{VERSION}
@subtitle @value{UPDATED}
+
@page
@vskip 0pt plus 1filll
@insertcopying
@summarycontents
@contents
-@node Top, About, , (dir)
-@top OpenOCD
-
-This manual documents edition @value{EDITION} of the Open On-Chip Debugger
-(OpenOCD) version @value{VERSION}, @value{UPDATED}.
+@ifnottex
+@node Top
+@top OpenOCD User's Guide
@insertcopying
+@end ifnottex
@menu
* About:: About OpenOCD
* Daemon Configuration:: Daemon Configuration
* Interface - Dongle Configuration:: Interface - Dongle Configuration
* Reset Configuration:: Reset Configuration
-* Tap Creation:: Tap Creation
-* Target Configuration:: Target Configuration
+* TAP Declaration:: TAP Declaration
+* CPU Configuration:: CPU Configuration
* Flash Commands:: Flash Commands
* NAND Flash Commands:: NAND Flash Commands
* General Commands:: General Commands
+* Architecture and Core Commands:: Architecture and Core Commands
* JTAG Commands:: JTAG Commands
* Sample Scripts:: Sample Target Scripts
* TFTP:: TFTP
* FAQ:: Frequently Asked Questions
* Tcl Crash Course:: Tcl Crash Course
* License:: GNU Free Documentation License
+
@comment DO NOT use the plain word ``Index'', reason: CYGWIN filename
@comment case issue with ``Index.html'' and ``index.html''
@comment Occurs when creating ``--html --no-split'' output
devices.
@b{JTAG:} OpenOCD uses a ``hardware interface dongle'' to communicate
-with the JTAG (IEEE 1149.1) compliant taps on your target board.
+with the JTAG (IEEE 1149.1) compliant TAPs on your target board.
+A @dfn{TAP} is a ``Test Access Port'', a module which processes
+special instructions and data. TAPs are daisy-chained within and
+between chips and boards.
@b{Dongles:} OpenOCD currently supports many types of hardware dongles: USB
based, parallel port based, and other standalone boxes that run
@uref{http://openocd.berlios.de/web/}
+@section Latest User's Guide:
+
+The user's guide you are now reading may not be the latest one
+available. A version for more recent code may be available.
+Its HTML form is published irregularly at:
+
+@uref{http://openocd.berlios.de/doc/}
+
+PDF form is likewise published at:
+
+@uref{http://openocd.berlios.de/doc/pdf/}
+
+@section OpenOCD User's Forum
+
+There is an OpenOCD forum (phpBB) hosted by SparkFun:
+
+@uref{http://forum.sparkfun.com/viewforum.php?f=18}
+
@node Developers
@chapter OpenOCD Developer Resources
The OpenOCD Developer Mailing List provides the primary means of
communication between developers:
- @uref{https://lists.berlios.de/mailman/listinfo/openocd-development}
+@uref{https://lists.berlios.de/mailman/listinfo/openocd-development}
All drivers developers are enouraged to also subscribe to the list of
SVN commits to keep pace with the ongoing changes:
- @uref{https://lists.berlios.de/mailman/listinfo/openocd-svn}
+@uref{https://lists.berlios.de/mailman/listinfo/openocd-svn}
+
@node Building OpenOCD
@chapter Building OpenOCD
svn checkout svn://svn.berlios.de/openocd/trunk openocd
@end example
-Building OpenOCD requires a recent version of the GNU autotools (autoconf >= 2.59 and automake >= 1.9).
+If you prefer GIT based tools, the @command{git-svn} package works too:
+
+@example
+ git svn clone -s svn://svn.berlios.de/openocd
+@end example
+
+Building OpenOCD from a repository requires a recent version of the
+GNU autotools (autoconf >= 2.59 and automake >= 1.9).
For building on Windows,
you have to use Cygwin. Make sure that your @env{PATH} environment variable contains no
other locations with Unix utils (like UnxUtils) - these can't handle the Cygwin
board file. Boards may also contain multiple targets, i.e.: Two CPUs, or
a CPU and an FPGA or CPLD.
@item @b{target}
-@* Think chip. The ``target'' directory represents a JTAG tap (or
-chip) OpenOCD should control, not a board. Two common types of targets
+@* Think chip. The ``target'' directory represents the JTAG TAPs
+on a chip
+which OpenOCD should control, not a board. Two common types of targets
are ARM chips and FPGA or CPLD chips.
+When a chip has multiple TAPs (maybe it has both ARM and DSP cores),
+the target config file defines all of them.
@end itemize
@b{If needed...} The user in their ``openocd.cfg'' file or the board
@item SDRAM configuration (size, speed, etc.
@item Board specific IO configuration (i.e.: GPIO pins might disable a 2nd flash)
@item Multiple TARGET source statements
+@item Reset configuration
@item All things that are not ``inside a chip''
@item Things inside a chip go in a 'target' file
@end enumerate
@enumerate
@item Set defaults
-@item Create taps
-@item Reset configuration
-@item Work areas
+@item Add TAPs to the scan chain
+@item Add CPU targets
@item CPU/Chip/CPU-Core specific features
@item On-Chip flash
@end enumerate
# variable: _TARGETNAME = network.cpu
# other commands can refer to the "network.cpu" tap.
$_TARGETNAME configure .... params for this CPU..
-
+
set ENDIAN little
set CHIPNAME video
source [find target/pxa270.cfg]
# variable: _TARGETNAME = video.cpu
# other commands can refer to the "video.cpu" tap.
$_TARGETNAME configure .... params for this CPU..
-
+
unset ENDIAN
set CHIPNAME xilinx
source [find target/spartan3.cfg]
# these names still work!
network.cpu configure ... params
video.cpu configure ... params
-
@end example
@subsection Default Value Boiler Plate Code
@example
# SIMPLE example
-if @{ [info exists CHIPNAME] @} @{
- set _CHIPNAME $CHIPNAME
-@} else @{
+if @{ [info exists CHIPNAME] @} @{
+ set _CHIPNAME $CHIPNAME
+@} else @{
set _CHIPNAME sam7x256
@}
-if @{ [info exists ENDIAN] @} @{
- set _ENDIAN $ENDIAN
-@} else @{
+if @{ [info exists ENDIAN] @} @{
+ set _ENDIAN $ENDIAN
+@} else @{
set _ENDIAN little
@}
@} else @{
set _CPUTAPID 0x3f0f0f0f
@}
-
@end example
-@subsection Creating Taps
-After the ``defaults'' are choosen [see above] the taps are created.
+@subsection Adding TAPs to the Scan Chain
+After the ``defaults'' are set up,
+add the TAPs on each chip to the JTAG scan chain.
+@xref{TAP Declaration}, and the naming convention
+for taps.
-@b{SIMPLE example:} such as an Atmel AT91SAM7X256
+In the simplest case the chip has only one TAP,
+probably for a CPU or FPGA.
+The config file for the Atmel AT91SAM7X256
+looks (in part) like this:
@example
-# for an ARM7TDMI.
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf \
-expected-id $_CPUTAPID
@end example
-@b{COMPLEX example:}
-
-This is an SNIP/example for an STR912 - which has 3 internal taps. Key features shown:
-
-@enumerate
-@item @b{Unform tap names} - See: Tap Naming Convention
-@item @b{_TARGETNAME} is created at the end where used.
-@end enumerate
+A board with two such at91sam7 chips would be able
+to source such a config file twice, with different
+values for @code{CHIPNAME}, so
+it adds a different TAP each time.
-@example
-if @{ [info exists FLASHTAPID ] @} @{
- set _FLASHTAPID $FLASHTAPID
-@} else @{
- set _FLASHTAPID 0x25966041
-@}
-jtag newtap $_CHIPNAME flash -irlen 8 -ircapture 0x1 -irmask 0x1 \
- -expected-id $_FLASHTAPID
+There are more complex examples too, with chips that have
+multiple TAPs. Ones worth looking at include:
-if @{ [info exists CPUTAPID ] @} @{
- set _CPUTAPID $CPUTAPID
-@} else @{
- set _CPUTAPID 0x25966041
-@}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0xf -irmask 0xe \
- -expected-id $_CPUTAPID
+@itemize
+@item @file{target/omap3530.cfg} -- with a disabled ARM, and a JRC
+(there's a DSP too, which is not listed)
+@item @file{target/str912.cfg} -- with flash, CPU, and boundary scan
+@item @file{target/ti_dm355.cfg} -- with ETM, ARM, and JRC (this JRC
+is not currently used)
+@end itemize
+@subsection Add CPU targets
-if @{ [info exists BSTAPID ] @} @{
- set _BSTAPID $BSTAPID
-@} else @{
- set _BSTAPID 0x1457f041
-@}
-jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1 \
- -expected-id $_BSTAPID
+After adding a TAP for a CPU, you should set it up so that
+GDB and other commands can use it.
+@xref{CPU Configuration}.
+For the at91sam7 example above, the command can look like this:
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
+@example
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME arm7tdmi -chain-position $_TARGETNAME
@end example
-@b{Tap Naming Convention}
-
-See the command ``jtag newtap'' for detail, but in brief the names you should use are:
+Work areas are small RAM areas associated with CPU targets.
+They are used by OpenOCD to speed up downloads,
+and to download small snippets of code to program flash chips.
+If the chip includes a form of ``on-chip-ram'' - and many do - define
+a work area if you can.
+Again using the at91sam7 as an example, this can look like:
-@itemize @bullet
-@item @b{tap}
-@item @b{cpu}
-@item @b{flash}
-@item @b{bs}
-@item @b{etb}
-@item @b{jrc}
-@item @b{unknownN} - it happens :-(
-@end itemize
+@example
+$_TARGETNAME configure -work-area-phys 0x00200000 \
+ -work-area-size 0x4000 -work-area-backup 0
+@end example
@subsection Reset Configuration
-Some chips have specific ways the TRST and SRST signals are
-managed. If these are @b{CHIP SPECIFIC} they go here, if they are
-@b{BOARD SPECIFIC} they go in the board file.
+As a rule, you should put the @command{reset_config} command
+into the board file. Most things you think you know about a
+chip can be tweaked by the board.
-@subsection Work Areas
-
-Work areas are small RAM areas used by OpenOCD to speed up downloads,
-and to download small snippets of code to program flash chips.
-
-If the chip includes a form of ``on-chip-ram'' - and many do - define
-a reasonable work area and use the ``backup'' option.
-
-@b{PROBLEMS:} On more complex chips, this ``work area'' may become
-inaccessible if/when the application code enables or disables the MMU.
+Some chips have specific ways the TRST and SRST signals are
+managed. In the unusual case that these are @emph{chip specific}
+and can never be changed by board wiring, they could go here.
@subsection ARM Core Specific Hacks
examination of the instruction and data bus activity. Trace
activity is controlled through an ``Embedded Trace Module'' (ETM)
on one of the core's scan chains. The ETM emits voluminous data
-through a ``trace port''. The trace port is accessed in one
-of two ways. When its signals are pinned out from the chip,
-boards may provide a special high speed debugging connector;
-software support for this is not configured by default, use
-the ``--enable-oocd_trace'' option. Alternatively, trace data
-may be stored an on-chip SRAM which is packaged as an ``Embedded
-Trace Buffer'' (ETB). An ETB has its own TAP, usually right after
-its associated ARM core. OpenOCD supports the ETM, and your
-target configuration should set it up with the relevant trace
-port: ``etb'' for chips which use that, else the board-specific
-option will be either ``oocd_trace'' or ``dummy''.
+through a ``trace port''. (@xref{ARM Tracing}.)
+If you are using an external trace port,
+configure it in your board config file.
+If you are using an on-chip ``Embedded Trace Buffer'' (ETB),
+configure it in your target config file.
@example
etm config $_TARGETNAME 16 normal full etb
@* JIM-Tcl was introduced to OpenOCD in spring 2008.
@item @b{Need a crash course in Tcl?}
-@* See: @xref{Tcl Crash Course}.
+@*@xref{Tcl Crash Course}.
@end itemize
@node Daemon Configuration
the port @var{number} defaults to 4444.
@end deffn
-@section GDB Configuration
@anchor{GDB Configuration}
+@section GDB Configuration
@cindex GDB
@cindex GDB configuration
You can reconfigure some GDB behaviors if needed.
@xref{Target Create}, about declaring individual targets.
@xref{Target Events}, about configuring target-specific event handling.
-@deffn {Command} gdb_breakpoint_override <hard|soft|disable>
@anchor{gdb_breakpoint_override}
+@deffn {Command} gdb_breakpoint_override [@option{hard}|@option{soft}|@option{disable}]
Force breakpoint type for gdb @command{break} commands.
-The raison d'etre for this option is to support GDB GUI's which don't
+This option supports GDB GUIs which don't
distinguish hard versus soft breakpoints, if the default OpenOCD and
GDB behaviour is not sufficient. GDB normally uses hardware
breakpoints if the memory map has been set up for flash regions.
-
-This option replaces older arm7_9 target commands that addressed
-the same issue.
@end deffn
-@deffn {Config command} gdb_detach <resume|reset|halt|nothing>
+@deffn {Config command} gdb_detach (@option{resume}|@option{reset}|@option{halt}|@option{nothing})
Configures what OpenOCD will do when GDB detaches from the daemon.
-Default behaviour is @var{resume}.
+Default behaviour is @option{resume}.
@end deffn
-@deffn {Config command} gdb_flash_program <enable|disable>
@anchor{gdb_flash_program}
-Set to @var{enable} to cause OpenOCD to program the flash memory when a
+@deffn {Config command} gdb_flash_program (@option{enable}|@option{disable})
+Set to @option{enable} to cause OpenOCD to program the flash memory when a
vFlash packet is received.
-The default behaviour is @var{enable}.
+The default behaviour is @option{enable}.
@end deffn
-@deffn {Config command} gdb_memory_map <enable|disable>
-Set to @var{enable} to cause OpenOCD to send the memory configuration to GDB when
+@deffn {Config command} gdb_memory_map (@option{enable}|@option{disable})
+Set to @option{enable} to cause OpenOCD to send the memory configuration to GDB when
requested. GDB will then know when to set hardware breakpoints, and program flash
using the GDB load command. @command{gdb_flash_program enable} must also be enabled
for flash programming to work.
-Default behaviour is @var{enable}.
+Default behaviour is @option{enable}.
@xref{gdb_flash_program}.
@end deffn
-@deffn {Config command} gdb_report_data_abort <enable|disable>
+@deffn {Config command} gdb_report_data_abort (@option{enable}|@option{disable})
Specifies whether data aborts cause an error to be reported
by GDB memory read packets.
-The default behaviour is @var{disable};
-use @var{enable} see these errors reported.
+The default behaviour is @option{disable};
+use @option{enable} see these errors reported.
@end deffn
@node Interface - Dongle Configuration
@chapter Interface - Dongle Configuration
-Interface commands are normally found in an interface configuration
-file which is sourced by your openocd.cfg file. These commands tell
-OpenOCD what type of JTAG dongle you have and how to talk to it.
-@section Simple Complete Interface Examples
-@b{A Turtelizer FT2232 Based JTAG Dongle}
-@verbatim
-#interface
-interface ft2232
-ft2232_device_desc "Turtelizer JTAG/RS232 Adapter A"
-ft2232_layout turtelizer2
-ft2232_vid_pid 0x0403 0xbdc8
-@end verbatim
-@b{A SEGGER Jlink}
-@verbatim
+JTAG Adapters/Interfaces/Dongles are normally configured
+through commands in an interface configuration
+file which is sourced by your @file{openocd.cfg} file, or
+through a command line @option{-f interface/....cfg} option.
+
+@example
+source [find interface/olimex-jtag-tiny.cfg]
+@end example
+
+These commands tell
+OpenOCD what type of JTAG adapter you have, and how to talk to it.
+A few cases are so simple that you only need to say what driver to use:
+
+@example
# jlink interface
interface jlink
-@end verbatim
-@b{A Raisonance RLink}
-@verbatim
-# rlink interface
-interface rlink
-@end verbatim
-@b{Parallel Port}
-@verbatim
-interface parport
-parport_port 0xc8b8
-parport_cable wiggler
-jtag_speed 0
-@end verbatim
-@b{ARM-JTAG-EW}
-@verbatim
-interface arm-jtag-ew
-@end verbatim
-@section Interface Command
-
-The interface command tells OpenOCD what type of JTAG dongle you are
-using. Depending on the type of dongle, you may need to have one or
-more additional commands.
+@end example
-@itemize @bullet
+Most adapters need a bit more configuration than that.
-@item @b{interface} <@var{name}>
-@cindex interface
-@*Use the interface driver <@var{name}> to connect to the
-target. Currently supported interfaces are
-@itemize @minus
+@section Interface Configuration
-@item @b{parport}
-@* PC parallel port bit-banging (Wigglers, PLD download cable, ...)
+The interface command tells OpenOCD what type of JTAG dongle you are
+using. Depending on the type of dongle, you may need to have one or
+more additional commands.
-@item @b{amt_jtagaccel}
-@* Amontec Chameleon in its JTAG Accelerator configuration connected to a PC's EPP
-mode parallel port
+@deffn {Config Command} {interface} name
+Use the interface driver @var{name} to connect to the
+target.
+@end deffn
-@item @b{ft2232}
-@* FTDI FT2232 (USB) based devices using either the open-source libftdi or the binary only
-FTD2XX driver. The FTD2XX is superior in performance, but not available on every
-platform. The libftdi uses libusb, and should be portable to all systems that provide
-libusb.
+@deffn Command {jtag interface}
+Returns the name of the interface driver being used.
+@end deffn
-@item @b{ep93xx}
-@*Cirrus Logic EP93xx based single-board computer bit-banging (in development)
+@section Interface Drivers
-@item @b{presto}
-@* ASIX PRESTO USB JTAG programmer.
+Each of the interface drivers listed here must be explicitly
+enabled when OpenOCD is configured, in order to be made
+available at run time.
-@item @b{usbprog}
-@* usbprog is a freely programmable USB adapter.
+@deffn {Interface Driver} {amt_jtagaccel}
+Amontec Chameleon in its JTAG Accelerator configuration,
+connected to a PC's EPP mode parallel port.
+This defines some driver-specific commands:
-@item @b{gw16012}
-@* Gateworks GW16012 JTAG programmer.
+@deffn {Config Command} {parport_port} number
+Specifies either the address of the I/O port (default: 0x378 for LPT1) or
+the number of the @file{/dev/parport} device.
+@end deffn
-@item @b{jlink}
-@* Segger jlink USB adapter
+@deffn {Config Command} rtck [@option{enable}|@option{disable}]
+Displays status of RTCK option.
+Optionally sets that option first.
+@end deffn
+@end deffn
-@item @b{rlink}
-@* Raisonance RLink USB adapter
+@deffn {Interface Driver} {arm-jtag-ew}
+Olimex ARM-JTAG-EW USB adapter
+This has one driver-specific command:
-@item @b{vsllink}
-@* vsllink is part of Versaloon which is a versatile USB programmer.
+@deffn Command {armjtagew_info}
+Logs some status
+@end deffn
+@end deffn
-@item @b{arm-jtag-ew}
-@* Olimex ARM-JTAG-EW USB adapter
-@comment - End parameters
-@end itemize
-@comment - End Interface
-@end itemize
-@subsection parport options
+@deffn {Interface Driver} {at91rm9200}
+Supports bitbanged JTAG from the local system,
+presuming that system is an Atmel AT91rm9200
+and a specific set of GPIOs is used.
+@c command: at91rm9200_device NAME
+@c chooses among list of bit configs ... only one option
+@end deffn
-@itemize @bullet
-@item @b{parport_port} <@var{number}>
-@cindex parport_port
-@*Either the address of the I/O port (default: 0x378 for LPT1) or the number of
-the @file{/dev/parport} device
+@deffn {Interface Driver} {dummy}
+A dummy software-only driver for debugging.
+@end deffn
-When using PPDEV to access the parallel port, use the number of the parallel port:
-@option{parport_port 0} (the default). If @option{parport_port 0x378} is specified
-you may encounter a problem.
-@item @b{parport_cable} <@var{name}>
-@cindex parport_cable
-@*The layout of the parallel port cable used to connect to the target.
-Currently supported cables are
-@itemize @minus
-@item @b{wiggler}
-@cindex wiggler
-The original Wiggler layout, also supported by several clones, such
-as the Olimex ARM-JTAG
-@item @b{wiggler2}
-@cindex wiggler2
-Same as original wiggler except an led is fitted on D5.
-@item @b{wiggler_ntrst_inverted}
-@cindex wiggler_ntrst_inverted
-Same as original wiggler except TRST is inverted.
-@item @b{old_amt_wiggler}
-@cindex old_amt_wiggler
-The Wiggler configuration that comes with Amontec's Chameleon Programmer. The new
-version available from the website uses the original Wiggler layout ('@var{wiggler}')
-@item @b{chameleon}
-@cindex chameleon
-The Amontec Chameleon's CPLD when operated in configuration mode. This is only used to
-program the Chameleon itself, not a connected target.
-@item @b{dlc5}
-@cindex dlc5
-The Xilinx Parallel cable III.
-@item @b{triton}
-@cindex triton
-The parallel port adapter found on the 'Karo Triton 1 Development Board'.
-This is also the layout used by the HollyGates design
-(see @uref{http://www.lartmaker.nl/projects/jtag/}).
-@item @b{flashlink}
-@cindex flashlink
-The ST Parallel cable.
-@item @b{arm-jtag}
-@cindex arm-jtag
-Same as original wiggler except SRST and TRST connections reversed and
-TRST is also inverted.
-@item @b{altium}
-@cindex altium
-Altium Universal JTAG cable.
-@end itemize
-@item @b{parport_write_on_exit} <@var{on}|@var{off}>
-@cindex parport_write_on_exit
-@*This will configure the parallel driver to write a known value to the parallel
-interface on exiting OpenOCD
-@end itemize
+@deffn {Interface Driver} {ep93xx}
+Cirrus Logic EP93xx based single-board computer bit-banging (in development)
+@end deffn
-@subsection amt_jtagaccel options
-@itemize @bullet
-@item @b{parport_port} <@var{number}>
-@cindex parport_port
-@*Either the address of the I/O port (default: 0x378 for LPT1) or the number of the
-@file{/dev/parport} device
-@end itemize
-@subsection ft2232 options
+@deffn {Interface Driver} {ft2232}
+FTDI FT2232 (USB) based devices over one of the userspace libraries.
+These interfaces have several commands, used to configure the driver
+before initializing the JTAG scan chain:
-@itemize @bullet
-@item @b{ft2232_device_desc} <@var{description}>
-@cindex ft2232_device_desc
-@*The USB device description of the FTDI FT2232 device. If not
+@deffn {Config Command} {ft2232_device_desc} description
+Provides the USB device description (the @emph{iProduct string})
+of the FTDI FT2232 device. If not
specified, the FTDI default value is used. This setting is only valid
if compiled with FTD2XX support.
+@end deffn
+
+@deffn {Config Command} {ft2232_serial} serial-number
+Specifies the @var{serial-number} of the FTDI FT2232 device to use,
+in case the vendor provides unique IDs and more than one FT2232 device
+is connected to the host.
+If not specified, serial numbers are not considered.
+@end deffn
-@b{TODO:} Confirm the following: On Windows the name needs to end with
-a ``space A''? Or not? It has to do with the FTD2xx driver. When must
-this be added and when must it not be added? Why can't the code in the
-interface or in OpenOCD automatically add this if needed? -- Duane.
-
-@item @b{ft2232_serial} <@var{serial-number}>
-@cindex ft2232_serial
-@*The serial number of the FTDI FT2232 device. If not specified, the FTDI default
-values are used.
-@item @b{ft2232_layout} <@var{name}>
-@cindex ft2232_layout
-@*The layout of the FT2232 GPIO signals used to control output-enables and reset
-signals. Valid layouts are
+@deffn {Config Command} {ft2232_layout} name
+Each vendor's FT2232 device can use different GPIO signals
+to control output-enables, reset signals, and LEDs.
+Currently valid layout @var{name} values include:
@itemize @minus
-@item @b{usbjtag}
-"USBJTAG-1" layout described in the original OpenOCD diploma thesis
-@item @b{jtagkey}
-Amontec JTAGkey and JTAGkey-Tiny
-@item @b{signalyzer}
-Signalyzer
-@item @b{olimex-jtag}
-Olimex ARM-USB-OCD
-@item @b{m5960}
-American Microsystems M5960
-@item @b{evb_lm3s811}
-Luminary Micro EVB_LM3S811 as a JTAG interface (not onboard processor), no TRST or
-SRST signals on external connector
-@item @b{comstick}
-Hitex STR9 comstick
-@item @b{stm32stick}
-Hitex STM32 Performance Stick
-@item @b{flyswatter}
-Tin Can Tools Flyswatter
-@item @b{turtelizer2}
-egnite Software turtelizer2
-@item @b{oocdlink}
-OOCDLink
-@item @b{axm0432_jtag}
-Axiom AXM-0432
-@item @b{cortino}
-Hitex Cortino JTAG interface
+@item @b{axm0432_jtag} Axiom AXM-0432
+@item @b{comstick} Hitex STR9 comstick
+@item @b{cortino} Hitex Cortino JTAG interface
+@item @b{evb_lm3s811} Luminary Micro EVB_LM3S811 as a JTAG interface
+(bypassing onboard processor), no TRST or SRST signals on external connector
+@item @b{flyswatter} Tin Can Tools Flyswatter
+@item @b{icebear} ICEbear JTAG adapter from Section 5
+@item @b{jtagkey} Amontec JTAGkey and JTAGkey-Tiny (and compatibles)
+@item @b{m5960} American Microsystems M5960
+@item @b{olimex-jtag} Olimex ARM-USB-OCD and ARM-USB-Tiny
+@item @b{oocdlink} OOCDLink
+@c oocdlink ~= jtagkey_prototype_v1
+@item @b{sheevaplug} Marvell Sheevaplug development kit
+@item @b{signalyzer} Xverve Signalyzer
+@item @b{stm32stick} Hitex STM32 Performance Stick
+@item @b{turtelizer2} egnite Software turtelizer2
+@item @b{usbjtag} "USBJTAG-1" layout described in the OpenOCD diploma thesis
@end itemize
+@end deffn
-@item @b{ft2232_vid_pid} <@var{vid}> <@var{pid}>
-@*The vendor ID and product ID of the FTDI FT2232 device. If not specified, the FTDI
-default values are used. Multiple <@var{vid}>, <@var{pid}> pairs may be given, e.g.
+@deffn {Config Command} {ft2232_vid_pid} [vid pid]+
+The vendor ID and product ID of the FTDI FT2232 device. If not specified, the FTDI
+default values are used.
+Currently, up to eight [@var{vid}, @var{pid}] pairs may be given, e.g.
@example
ft2232_vid_pid 0x0403 0xcff8 0x15ba 0x0003
@end example
-@item @b{ft2232_latency} <@var{ms}>
-@*On some systems using FT2232 based JTAG interfaces the FT_Read function call in
+@end deffn
+
+@deffn {Config Command} {ft2232_latency} ms
+On some systems using FT2232 based JTAG interfaces the FT_Read function call in
ft2232_read() fails to return the expected number of bytes. This can be caused by
USB communication delays and has proved hard to reproduce and debug. Setting the
FT2232 latency timer to a larger value increases delays for short USB packets but it
also reduces the risk of timeouts before receiving the expected number of bytes.
The OpenOCD default value is 2 and for some systems a value of 10 has proved useful.
+@end deffn
+
+For example, the interface config file for a
+Turtelizer JTAG Adapter looks something like this:
+
+@example
+interface ft2232
+ft2232_device_desc "Turtelizer JTAG/RS232 Adapter"
+ft2232_layout turtelizer2
+ft2232_vid_pid 0x0403 0xbdc8
+@end example
+@end deffn
+
+@deffn {Interface Driver} {gw16012}
+Gateworks GW16012 JTAG programmer.
+This has one driver-specific command:
+
+@deffn {Config Command} {parport_port} number
+Specifies either the address of the I/O port (default: 0x378 for LPT1) or
+the number of the @file{/dev/parport} device.
+@end deffn
+@end deffn
+
+@deffn {Interface Driver} {jlink}
+Segger jlink USB adapter
+@c command: jlink_info
+@c dumps status
+@c command: jlink_hw_jtag (2|3)
+@c sets version 2 or 3
+@end deffn
+
+@deffn {Interface Driver} {parport}
+Supports PC parallel port bit-banging cables:
+Wigglers, PLD download cable, and more.
+These interfaces have several commands, used to configure the driver
+before initializing the JTAG scan chain:
+
+@deffn {Config Command} {parport_cable} name
+The layout of the parallel port cable used to connect to the target.
+Currently valid cable @var{name} values include:
+
+@itemize @minus
+@item @b{altium} Altium Universal JTAG cable.
+@item @b{arm-jtag} Same as original wiggler except SRST and
+TRST connections reversed and TRST is also inverted.
+@item @b{chameleon} The Amontec Chameleon's CPLD when operated
+in configuration mode. This is only used to
+program the Chameleon itself, not a connected target.
+@item @b{dlc5} The Xilinx Parallel cable III.
+@item @b{flashlink} The ST Parallel cable.
+@item @b{lattice} Lattice ispDOWNLOAD Cable
+@item @b{old_amt_wiggler} The Wiggler configuration that comes with
+some versions of
+Amontec's Chameleon Programmer. The new version available from
+the website uses the original Wiggler layout ('@var{wiggler}')
+@item @b{triton} The parallel port adapter found on the
+``Karo Triton 1 Development Board''.
+This is also the layout used by the HollyGates design
+(see @uref{http://www.lartmaker.nl/projects/jtag/}).
+@item @b{wiggler} The original Wiggler layout, also supported by
+several clones, such as the Olimex ARM-JTAG
+@item @b{wiggler2} Same as original wiggler except an led is fitted on D5.
+@item @b{wiggler_ntrst_inverted} Same as original wiggler except TRST is inverted.
@end itemize
+@end deffn
-@subsection ep93xx options
-@cindex ep93xx options
-Currently, there are no options available for the ep93xx interface.
+@deffn {Config Command} {parport_port} number
+Either the address of the I/O port (default: 0x378 for LPT1) or the number of
+the @file{/dev/parport} device
+
+When using PPDEV to access the parallel port, use the number of the parallel port:
+@option{parport_port 0} (the default). If @option{parport_port 0x378} is specified
+you may encounter a problem.
+@end deffn
+
+@deffn {Config Command} {parport_write_on_exit} (on|off)
+This will configure the parallel driver to write a known
+cable-specific value to the parallel interface on exiting OpenOCD
+@end deffn
+
+For example, the interface configuration file for a
+classic ``Wiggler'' cable might look something like this:
+
+@example
+interface parport
+parport_port 0xc8b8
+parport_cable wiggler
+@end example
+@end deffn
+
+@deffn {Interface Driver} {presto}
+ASIX PRESTO USB JTAG programmer.
+@c command: presto_serial str
+@c sets serial number
+@end deffn
+
+@deffn {Interface Driver} {rlink}
+Raisonance RLink USB adapter
+@end deffn
+
+@deffn {Interface Driver} {usbprog}
+usbprog is a freely programmable USB adapter.
+@end deffn
+
+@deffn {Interface Driver} {vsllink}
+vsllink is part of Versaloon which is a versatile USB programmer.
+
+@quotation Note
+This defines quite a few driver-specific commands,
+which are not currently documented here.
+@end quotation
+@end deffn
+
+@deffn {Interface Driver} {ZY1000}
+This is the Zylin ZY1000 JTAG debugger.
+
+@quotation Note
+This defines some driver-specific commands,
+which are not currently documented here.
+@end quotation
+
+@deffn Command power [@option{on}|@option{off}]
+Turn power switch to target on/off.
+No arguments: print status.
+@end deffn
+
+@end deffn
-@section JTAG Speed
@anchor{JTAG Speed}
+@section JTAG Speed
JTAG clock setup is part of system setup.
It @emph{does not belong with interface setup} since any interface
only knows a few of the constraints for the JTAG clock speed.
Every system configuration may require a different reset
configuration. This can also be quite confusing.
+Resets also interact with @var{reset-init} event handlers,
+which do things like setting up clocks and DRAM, and
+JTAG clock rates. (@xref{JTAG Speed}.)
Please see the various board files for examples.
-@b{Note} to maintainers and integrators:
+@quotation Note
+To maintainers and integrators:
Reset configuration touches several things at once.
Normally the board configuration file
should define it and assume that the JTAG adapter supports
And when the JTAG adapter doesn't support everything, the
system configuration file will need to override parts of
the reset configuration provided by other files.
+@end quotation
@section Types of Reset
board-specific script might do things like setting up DRAM.
(@xref{Reset Command}.)
-@section SRST and TRST Signal Issues
+@section SRST and TRST Issues
Because SRST and TRST are hardware signals, they can have a
variety of system-specific constraints. Some of the most
signals to both levels (push/pull) to minimize rise times.
Use the @command{reset_config} @var{trst_type} and
@var{srst_type} parameters to say how to drive reset signals.
+
+@item @emph{Special initialization} ... Targets sometimes need
+special JTAG initialization sequences to handle chip-specific
+issues (not limited to errata).
+For example, certain JTAG commands might need to be issued while
+the system as a whole is in a reset state (SRST active)
+but the JTAG scan chain is usable (TRST inactive).
+(@xref{JTAG Commands}, where the @command{jtag_reset}
+command is presented.)
@end itemize
There can also be other issues.
Some devices don't fully conform to the JTAG specifications.
-Others have chip-specific extensions like extra steps needed
-during TAP reset, or a requirement to use the normally-optional TRST
-signal.
Trivial system-specific differences are common, such as
SRST and TRST using slightly different names.
+There are also vendors who distribute key JTAG documentation for
+their chips only to developers who have signed a Non-Disclosure
+Agreement (NDA).
+
+Sometimes there are chip-specific extensions like a requirement to use
+the normally-optional TRST signal (precluding use of JTAG adapters which
+don't pass TRST through), or needing extra steps to complete a TAP reset.
+
+In short, SRST and especially TRST handling may be very finicky,
+needing to cope with both architecture and board specific constraints.
@section Commands for Handling Resets
nTRST (active-low JTAG TAP reset) before starting new JTAG operations.
@end deffn
-@deffn {Command} reset_config signals [combination [trst_type [srst_type]]]
+@deffn {Command} reset_config mode_flag ...
This command tells OpenOCD the reset configuration
-of your combination of JTAG interface, board, and target.
-If the JTAG interface provides SRST, but the board doesn't connect
-that signal properly, then OpenOCD can't use it. @var{signals} can
-be @option{none}, @option{trst_only}, @option{srst_only} or
-@option{trst_and_srst}.
+of your combination of JTAG board and target in target
+configuration scripts.
+
+If you have an interface that does not support SRST and
+TRST(unlikely), then you may be able to work around that
+problem by using a reset_config command to override any
+settings in the target configuration script.
+
+SRST and TRST has a fairly well understood definition and
+behaviour in the JTAG specification, but vendors take
+liberties to achieve various more or less clearly understood
+goals. Sometimes documentation is available, other times it
+is not. OpenOCD has the reset_config command to allow OpenOCD
+to deal with the various common cases.
+
+The @var{mode_flag} options can be specified in any order, but only one
+of each type -- @var{signals}, @var{combination}, @var{trst_type},
+and @var{srst_type} -- may be specified at a time.
+If you don't provide a new value for a given type, its previous
+value (perhaps the default) is unchanged.
+For example, this means that you don't need to say anything at all about
+TRST just to declare that if the JTAG adapter should want to drive SRST,
+it must explicitly be driven high (@option{srst_push_pull}).
+
+@var{signals} can specify which of the reset signals are connected.
+For example, If the JTAG interface provides SRST, but the board doesn't
+connect that signal properly, then OpenOCD can't use it.
+Possible values are @option{none} (the default), @option{trst_only},
+@option{srst_only} and @option{trst_and_srst}.
+
+@quotation Tip
+If your board provides SRST or TRST through the JTAG connector,
+you must declare that or else those signals will not be used.
+@end quotation
The @var{combination} is an optional value specifying broken reset
-signal implementations. @option{srst_pulls_trst} states that the
+signal implementations.
+The default behaviour if no option given is @option{separate},
+indicating everything behaves normally.
+@option{srst_pulls_trst} states that the
test logic is reset together with the reset of the system (e.g. Philips
LPC2000, "broken" board layout), @option{trst_pulls_srst} says that
the system is reset together with the test logic (only hypothetical, I
haven't seen hardware with such a bug, and can be worked around).
@option{combined} implies both @option{srst_pulls_trst} and
-@option{trst_pulls_srst}. The default behaviour if no option given is
-@option{separate}.
+@option{trst_pulls_srst}.
The optional @var{trst_type} and @var{srst_type} parameters allow the
-driver type of the reset lines to be specified. Possible values are
-@option{trst_push_pull} (default) and @option{trst_open_drain} for the
-test reset signal, and @option{srst_open_drain} (default) and
-@option{srst_push_pull} for the system reset. These values only affect
-JTAG interfaces with support for different drivers, like the Amontec
-JTAGkey and JTAGAccelerator.
+driver mode of each reset line to be specified. These values only affect
+JTAG interfaces with support for different driver modes, like the Amontec
+JTAGkey and JTAGAccelerator. Also, they are necessarily ignored if the
+relevant signal (TRST or SRST) is not connected.
+
+Possible @var{trst_type} driver modes for the test reset signal (TRST)
+are @option{trst_push_pull} (default) and @option{trst_open_drain}.
+Most boards connect this signal to a pulldown, so the JTAG TAPs
+never leave reset unless they are hooked up to a JTAG adapter.
+
+Possible @var{srst_type} driver modes for the system reset signal (SRST)
+are the default @option{srst_open_drain}, and @option{srst_push_pull}.
+Most boards connect this signal to a pullup, and allow the
+signal to be pulled low by various events including system
+powerup and pressing a reset button.
@end deffn
-@node Tap Creation
-@chapter Tap Creation
-@cindex tap creation
-@cindex tap configuration
+@node TAP Declaration
+@chapter TAP Declaration
+@cindex TAP declaration
+@cindex TAP configuration
-In order for OpenOCD to control a target, a JTAG tap must be
-defined/created.
+@emph{Test Access Ports} (TAPs) are the core of JTAG.
+TAPs serve many roles, including:
-Commands to create taps are normally found in a configuration file and
-are not normally typed by a human.
-
-When a tap is created a @b{dotted.name} is created for the tap. Other
-commands use that dotted.name to manipulate or refer to the tap.
-
-Tap Uses:
@itemize @bullet
-@item @b{Debug Target} A tap can be used by a GDB debug target
-@item @b{Flash Programing} Some chips program the flash directly via JTAG,
-instead of indirectly by making a CPU do it.
-@item @b{Boundry Scan} Some chips support boundary scan.
+@item @b{Debug Target} A CPU TAP can be used as a GDB debug target
+@item @b{Flash Programing} Some chips program the flash directly via JTAG.
+Others do it indirectly, making a CPU do it.
+@item @b{Program Download} Using the same CPU support GDB uses,
+you can initialize a DRAM controller, download code to DRAM, and then
+start running that code.
+@item @b{Boundary Scan} Most chips support boundary scan, which
+helps test for board assembly problems like solder bridges
+and missing connections
@end itemize
+OpenOCD must know about the active TAPs on your board(s).
+Setting up the TAPs is the core task of your configuration files.
+Once those TAPs are set up, you can pass their names to code
+which sets up CPUs and exports them as GDB targets,
+probes flash memory, performs low-level JTAG operations, and more.
+
+@section Scan Chains
+
+OpenOCD uses a JTAG adapter (interface) to talk to your board,
+which has a daisy chain of TAPs.
+That daisy chain is called a @dfn{scan chain}.
+Simple configurations may have a single TAP in the scan chain,
+perhaps for a microcontroller.
+Complex configurations might have a dozen or more TAPs:
+several in one chip, more in the next, and connecting
+to other boards with their own chips and TAPs.
+
+Unfortunately those TAPs can't always be autoconfigured,
+because not all devices provide good support for that.
+(JTAG doesn't require supporting IDCODE instructions.)
+The configuration mechanism currently supported by OpenOCD
+requires explicit configuration of all TAP devices using
+@command{jtag newtap} commands.
+One like this would declare a tap and name it @code{chip1.cpu}:
-@section jtag newtap
-@b{@t{jtag newtap CHIPNAME TAPNAME configparams ....}}
-@cindex jtag_device
-@cindex jtag newtap
-@cindex tap
-@cindex tap order
-@cindex tap geometry
+@example
+jtag newtap chip1 cpu -irlen 7 -ircapture 0x01 -irmask 0x55
+@end example
+
+Each target configuration file lists the TAPs provided
+by a given chip.
+Board configuration files combine all the targets on a board,
+and so forth.
+Note that @emph{the order in which TAPs are declared is very important.}
+It must match the order in the JTAG scan chain, both inside
+a single chip and between them.
+@xref{FAQ TAP Order}.
+
+For example, the ST Microsystems STR912 chip has
+three separate TAPs@footnote{See the ST
+document titled: @emph{STR91xFAxxx, Section 3.15 Jtag Interface, Page:
+28/102, Figure 3: JTAG chaining inside the STR91xFA}.
+@url{http://eu.st.com/stonline/products/literature/ds/13495.pdf}}.
+To configure those taps, @file{target/str912.cfg}
+includes commands something like this:
-@comment START options
-@itemize @bullet
-@item @b{CHIPNAME}
-@* is a symbolic name of the chip.
-@item @b{TAPNAME}
-@* is a symbol name of a tap present on the chip.
-@item @b{Required configparams}
-@* Every tap has 3 required configparams, and several ``optional
-parameters'', the required parameters are:
-@comment START REQUIRED
-@itemize @bullet
-@item @b{-irlen NUMBER} - the length in bits of the instruction register, mostly 4 or 5 bits.
-@item @b{-ircapture NUMBER} - the IDCODE capture command, usually 0x01.
-@item @b{-irmask NUMBER} - the corresponding mask for the IR register. For
-some devices, there are bits in the IR that aren't used. This lets you mask
-them off when doing comparisons. In general, this should just be all ones for
-the size of the IR.
-@comment END REQUIRED
-@end itemize
-An example of a FOOBAR Tap
@example
-jtag newtap foobar tap -irlen 7 -ircapture 0x42 -irmask 0x55
+jtag newtap str912 flash ... params ...
+jtag newtap str912 cpu ... params ...
+jtag newtap str912 bs ... params ...
@end example
-Creates the tap ``foobar.tap'' with the instruction register (IR) is 7
-bits long, during Capture-IR 0x42 is loaded into the IR, and bits
-[6,4,2,0] are checked.
-@item @b{Optional configparams}
-@comment START Optional
+Actual config files use a variable instead of literals like
+@option{str912}, to support more than one chip of each type.
+@xref{Config File Guidelines}.
+
+@section TAP Names
+
+When TAP objects are declared with @command{jtag newtap},
+a @dfn{dotted.name} is created for the TAP, combining the
+name of a module (usually a chip) and a label for the TAP.
+For example: @code{xilinx.tap}, @code{str912.flash},
+@code{omap3530.jrc}, @code{dm6446.dsp}, or @code{stm32.cpu}.
+Many other commands use that dotted.name to manipulate or
+refer to the TAP. For example, CPU configuration uses the
+name, as does declaration of NAND or NOR flash banks.
+
+The components of a dotted name should follow ``C'' symbol
+name rules: start with an alphabetic character, then numbers
+and underscores are OK; while others (including dots!) are not.
+
+@quotation Tip
+In older code, JTAG TAPs were numbered from 0..N.
+This feature is still present.
+However its use is highly discouraged, and
+should not be counted upon.
+Update all of your scripts to use TAP names rather than numbers.
+Using TAP numbers in target configuration scripts prevents
+reusing on boards with multiple targets.
+@end quotation
+
+@section TAP Declaration Commands
+
+@c shouldn't this be(come) a {Config Command}?
+@anchor{jtag newtap}
+@deffn Command {jtag newtap} chipname tapname configparams...
+Declares a new TAP with the dotted name @var{chipname}.@var{tapname},
+and configured according to the various @var{configparams}.
+
+The @var{chipname} is a symbolic name for the chip.
+Conventionally target config files use @code{$_CHIPNAME},
+defaulting to the model name given by the chip vendor but
+overridable.
+
+@cindex TAP naming convention
+The @var{tapname} reflects the role of that TAP,
+and should follow this convention:
+
@itemize @bullet
-@item @b{-expected-id NUMBER}
-@* By default it is zero. If non-zero represents the
-expected tap ID used when the JTAG chain is examined. Repeat
-the option as many times as required if multiple id's can be
-expected. See below.
-@item @b{-disable}
-@item @b{-enable}
-@* By default not specified the tap is enabled. Some chips have a
-JTAG route controller (JRC) that is used to enable and/or disable
-specific JTAG taps. You can later enable or disable any JTAG tap via
-the command @b{jtag tapenable DOTTED.NAME} or @b{jtag tapdisable
-DOTTED.NAME}
-@comment END Optional
+@item @code{bs} -- For boundary scan if this is a seperate TAP;
+@item @code{cpu} -- The main CPU of the chip, alternatively
+@code{arm} and @code{dsp} on chips with both ARM and DSP CPUs,
+@code{arm1} and @code{arm2} on chips two ARMs, and so forth;
+@item @code{etb} -- For an embedded trace buffer (example: an ARM ETB11);
+@item @code{flash} -- If the chip has a flash TAP, like the str912;
+@item @code{jrc} -- For JTAG route controller (example: the ICEpick modules
+on many Texas Instruments chips, like the OMAP3530 on Beagleboards);
+@item @code{tap} -- Should be used only FPGA or CPLD like devices
+with a single TAP;
+@item @code{unknownN} -- If you have no idea what the TAP is for (N is a number);
+@item @emph{when in doubt} -- Use the chip maker's name in their data sheet.
+For example, the Freescale IMX31 has a SDMA (Smart DMA) with
+a JTAG TAP; that TAP should be named @code{sdma}.
@end itemize
-@comment END OPTIONS
-@end itemize
-@b{Notes:}
-@comment START NOTES
-@itemize @bullet
-@item @b{Technically}
-@* newtap is a sub command of the ``jtag'' command
-@item @b{Big Picture Background}
-@*GDB Talks to OpenOCD using the GDB protocol via
-TCP/IP. OpenOCD then uses the JTAG interface (the dongle) to
-control the JTAG chain on your board. Your board has one or more chips
-in a @i{daisy chain configuration}. Each chip may have one or more
-JTAG taps. GDB ends up talking via OpenOCD to one of the taps.
-@item @b{NAME Rules}
-@*Names follow ``C'' symbol name rules (start with alpha ...)
-@item @b{TAPNAME - Conventions}
+Every TAP requires at least the following @var{configparams}:
+
@itemize @bullet
-@item @b{tap} - should be used only FPGA or CPLD like devices with a single tap.
-@item @b{cpu} - the main CPU of the chip, alternatively @b{foo.arm} and @b{foo.dsp}
-@item @b{flash} - if the chip has a flash tap, example: str912.flash
-@item @b{bs} - for boundary scan if this is a seperate tap.
-@item @b{etb} - for an embedded trace buffer (example: an ARM ETB11)
-@item @b{jrc} - for JTAG route controller (example: OMAP3530 found on Beagleboards)
-@item @b{unknownN} - where N is a number if you have no idea what the tap is for
-@item @b{Other names} - Freescale IMX31 has a SDMA (smart dma) with a JTAG tap, that tap should be called the ``sdma'' tap.
-@item @b{When in doubt} - use the chip maker's name in their data sheet.
+@item @code{-ircapture} @var{NUMBER}
+@*The IDCODE capture command, such as 0x01.
+@item @code{-irlen} @var{NUMBER}
+@*The length in bits of the
+instruction register, such as 4 or 5 bits.
+@item @code{-irmask} @var{NUMBER}
+@*A mask for the IR register.
+For some devices, there are bits in the IR that aren't used.
+This lets OpenOCD mask them off when doing IDCODE comparisons.
+In general, this should just be all ones for the size of the IR.
@end itemize
-@item @b{DOTTED.NAME}
-@* @b{CHIPNAME}.@b{TAPNAME} creates the tap name, aka: the
-@b{Dotted.Name} is the @b{CHIPNAME} and @b{TAPNAME} combined with a
-dot (period); for example: @b{xilinx.tap}, @b{str912.flash},
-@b{omap3530.jrc}, or @b{stm32.cpu} The @b{dotted.name} is used in
-numerous other places to refer to various taps.
-@item @b{ORDER}
-@* The order this command appears via the config files is
-important.
-@item @b{Multi Tap Example}
-@* This example is based on the ST Microsystems STR912. See the ST
-document titled: @b{STR91xFAxxx, Section 3.15 Jtag Interface, Page:
-28/102, Figure 3: JTAG chaining inside the STR91xFA}.
-@url{http://eu.st.com/stonline/products/literature/ds/13495.pdf}
-@*@b{checked: 28/nov/2008}
+A TAP may also provide optional @var{configparams}:
-The diagram shows that the TDO pin connects to the flash tap, flash TDI
-connects to the CPU debug tap, CPU TDI connects to the boundary scan
-tap which then connects to the TDI pin.
+@itemize @bullet
+@item @code{-disable} (or @code{-enable})
+@*Use the @code{-disable} paramater to flag a TAP which is not
+linked in to the scan chain when it is declared.
+You may use @code{-enable} to highlight the default state
+(the TAP is linked in).
+@xref{Enabling and Disabling TAPs}.
+@item @code{-expected-id} @var{number}
+@*A non-zero value represents the expected 32-bit IDCODE
+found when the JTAG chain is examined.
+These codes are not required by all JTAG devices.
+@emph{Repeat the option} as many times as required if more than one
+ID code could appear (for example, multiple versions).
+@end itemize
+@end deffn
-@example
- # The order is...
- # create tap: 'str912.flash'
- jtag newtap str912 flash ... params ...
- # create tap: 'str912.cpu'
- jtag newtap str912 cpu ... params ...
- # create tap: 'str912.bs'
- jtag newtap str912 bs ... params ...
-@end example
+@c @deffn Command {jtag arp_init-reset}
+@c ... more or less "init" ?
-@item @b{Note: Deprecated} - Index Numbers
-@* Prior to 28/nov/2008, JTAG taps where numbered from 0..N this
-feature is still present, however its use is highly discouraged and
-should not be counted upon. Update all of your scripts to use
-TAP names rather than numbers.
-@item @b{Multiple chips}
-@* If your board has multiple chips, you should be
-able to @b{source} two configuration files, in the proper order, and
-have the taps created in the proper order.
-@comment END NOTES
-@end itemize
-@comment at command level
-@comment DOCUMENT old command
-@section jtag_device - REMOVED
-@example
-@b{jtag_device} <@var{IR length}> <@var{IR capture}> <@var{IR mask}> <@var{IDCODE instruction}>
-@end example
-@cindex jtag_device
-
-@* @b{Removed: 28/nov/2008} This command has been removed and replaced
-by the ``jtag newtap'' command. The documentation remains here so that
-one can easily convert the old syntax to the new syntax. About the old
-syntax: The old syntax is positional, i.e.: The 3rd parameter is the
-``irmask''. The new syntax requires named prefixes, and supports
-additional options, for example ``-expected-id 0x3f0f0f0f''. Please refer to the
-@b{jtag newtap} command for details.
-@example
-OLD: jtag_device 8 0x01 0xe3 0xfe
-NEW: jtag newtap CHIPNAME TAPNAME -irlen 8 -ircapture 0x01 -irmask 0xe3
-@end example
+@anchor{Enabling and Disabling TAPs}
+@section Enabling and Disabling TAPs
+@cindex TAP events
-@section Enable/Disable Taps
-@b{Note:} These commands are intended to be used as a machine/script
-interface. Humans might find the ``scan_chain'' command more helpful
-when querying the state of the JTAG taps.
+In some systems, a @dfn{JTAG Route Controller} (JRC)
+is used to enable and/or disable specific JTAG TAPs.
+Many ARM based chips from Texas Instruments include
+an ``ICEpick'' module, which is a JRC.
+Such chips include DaVinci and OMAP3 processors.
-@b{By default, all taps are enabled}
+A given TAP may not be visible until the JRC has been
+told to link it into the scan chain; and if the JRC
+has been told to unlink that TAP, it will no longer
+be visible.
+Such routers address problems that JTAG ``bypass mode''
+ignores, such as:
-@itemize @bullet
-@item @b{jtag tapenable} @var{DOTTED.NAME}
-@item @b{jtag tapdisable} @var{DOTTED.NAME}
-@item @b{jtag tapisenabled} @var{DOTTED.NAME}
+@itemize
+@item The scan chain can only go as fast as its slowest TAP.
+@item Having many TAPs slows instruction scans, since all
+TAPs receive new instructions.
+@item TAPs in the scan chain must be powered up, which wastes
+power and prevents debugging some power management mechanisms.
@end itemize
-@cindex tap enable
-@cindex tap disable
-@cindex JRC
-@cindex route controller
-These commands are used when your target has a JTAG route controller
-that effectively adds or removes a tap from the JTAG chain in a
-non-standard way.
+The IEEE 1149.1 JTAG standard has no concept of a ``disabled'' tap,
+as implied by the existence of JTAG routers.
+However, the upcoming IEEE 1149.7 framework (layered on top of JTAG)
+does include a kind of JTAG router functionality.
-The ``standard way'' to remove a tap would be to place the tap in
-bypass mode. But with the advent of modern chips, this is not always a
-good solution. Some taps operate slowly, others operate fast, and
-there are other JTAG clock synchronisation problems one must face. To
-solve that problem, the JTAG route controller was introduced. Rather
-than ``bypass'' the tap, the tap is completely removed from the
-circuit and skipped.
+@c (a) currently the event handlers don't seem to be able to
+@c fail in a way that could lead to no-change-of-state.
+@c (b) eventually non-event configuration should be possible,
+@c in which case some this documentation must move.
+@deffn Command {jtag cget} dotted.name @option{-event} name
+@deffnx Command {jtag configure} dotted.name @option{-event} name string
+At this writing this mechanism is used only for event handling,
+and the only two events relate to TAP enabling and disabling.
-From OpenOCD's point of view, a JTAG tap is in one of 3 states:
+The @code{configure} subcommand assigns an event handler,
+a TCL string which is evaluated when the event is triggered.
+The @code{cget} subcommand returns that handler.
+The two possible values for an event @var{name}
+are @option{tap-disable} and @option{tap-enable}.
-@itemize @bullet
-@item @b{Enabled - Not In ByPass} and has a variable bit length
-@item @b{Enabled - In ByPass} and has a length of exactly 1 bit.
-@item @b{Disabled} and has a length of ZERO and is removed from the circuit.
-@end itemize
+So for example, when defining a TAP for a CPU connected to
+a JTAG router, you should define TAP event handlers using
+code that looks something like this:
-The IEEE JTAG definition has no concept of a ``disabled'' tap.
-@b{Historical note:} this feature was added 28/nov/2008
+@example
+jtag configure CHIP.cpu -event tap-enable @{
+ echo "Enabling CPU TAP"
+ ... jtag operations using CHIP.jrc
+@}
+jtag configure CHIP.cpu -event tap-disable @{
+ echo "Disabling CPU TAP"
+ ... jtag operations using CHIP.jrc
+@}
+@end example
+@end deffn
-@b{jtag tapisenabled DOTTED.NAME}
+@deffn Command {jtag tapdisable} dotted.name
+@deffnx Command {jtag tapenable} dotted.name
+@deffnx Command {jtag tapisenabled} dotted.name
+These three commands all return the string "1" if the tap
+specified by @var{dotted.name} is enabled,
+and "0" if it is disbabled.
+The @command{tapenable} variant first enables the tap
+by sending it a @option{tap-enable} event.
+The @command{tapdisable} variant first disables the tap
+by sending it a @option{tap-disable} event.
-This command returns 1 if the named tap is currently enabled, 0 if not.
-This command exists so that scripts that manipulate a JRC (like the
-OMAP3530 has) can determine if OpenOCD thinks a tap is presently
-enabled or disabled.
+@quotation Note
+Humans will find the @command{scan_chain} command more helpful
+than the script-oriented @command{tapisenabled}
+for querying the state of the JTAG taps.
+@end quotation
+@end deffn
-@page
-@node Target Configuration
-@chapter Target Configuration
+@node CPU Configuration
+@chapter CPU Configuration
@cindex GDB target
-This chapter discusses how to create a GDB debug target. Before
-creating a ``target'' a JTAG tap DOTTED.NAME must exist first.
+This chapter discusses how to create a GDB debug target for a CPU.
+You can also access these targets without GDB
+(@pxref{Architecture and Core Commands}) and, where relevant,
+through various kinds of NAND and NOR flash commands.
+Also, if you have multiple CPUs you can have multiple such targets.
+
+Before creating a ``target'', you must have added its TAP to the scan chain.
+When you've added that TAP, you will have a @code{dotted.name}
+which is used to set up the CPU support.
+The chip-specific configuration file will normally configure its CPU(s)
+right after it adds all of the chip's TAPs to the scan chain.
@section targets [NAME]
-@b{Note:} This command name is PLURAL - not singular.
+@b{Note:} This command name is PLURAL - not singular.
With NO parameter, this plural @b{targets} command lists all known
targets in a human friendly form.
Example:
@verbatim
(gdb) mon targets
- CmdName Type Endian ChainPos State
+ CmdName Type Endian ChainPos State
-- ---------- ---------- ---------- -------- ----------
0: target0 arm7tdmi little 0 halted
@end verbatim
@* Lists all supported target types (perhaps some are not yet in this document).
@item @b{names}
@* Lists all current debug target names, for example: 'str912.cpu' or 'pxa27.cpu' example usage:
-@verbatim
+@verbatim
foreach t [target names] {
puts [format "Target: %s\n" $t]
}
@section TARGETNAME (object) commands
@b{Use:} Once a target is created, an ``object name'' that represents the
target is created. By convention, the target name is identical to the
-tap name. In a multiple target system, one can preceed many common
+tap name. In a multiple target system, one can precede many common
commands with a specific target name and effect only that target.
@example
str912.cpu mww 0x1234 0x42
# Report
puts [format "The button is %s" $x]
@end example
-
+
In OpenOCD's terms, the ``target'' is an object just like a Tcl/Tk
button. Commands available as a ``target object'' are:
@* Invokes the specific event manually for the target
@end itemize
+@anchor{Target Events}
@section Target Events
@cindex events
-@anchor{Target Events}
At various times, certain things can happen, or you want them to happen.
Examples:
@}
mychip.cpu configure -event gdb-attach my_attach_proc
mychip.cpu configure -event gdb-attach @{
- puts "Reset..."
- reset halt
+ puts "Reset..."
+ reset halt
@}
@end example
@item @b{old-pre_resume}
@* DO NOT USE THIS: Used internally
@item @b{reset-assert-pre}
-@* Before reset is asserted on the tap.
+@* Issued as part of @command{reset} processing
+after SRST and/or TRST were activated and deactivated,
+but before reset is asserted on the tap.
@item @b{reset-assert-post}
-@* Reset is now asserted on the tap.
+@* Issued as part of @command{reset} processing
+when reset is asserted on the tap.
@item @b{reset-deassert-pre}
-@* Reset is about to be released on the tap
+@* Issued as part of @command{reset} processing
+when reset is about to be released on the tap.
@item @b{reset-deassert-post}
-@* Reset has been released on the tap
+@* Issued as part of @command{reset} processing
+when reset has been released on the tap.
@item @b{reset-end}
-@* Currently not used.
+@* Issued as the final step in @command{reset} processing.
@item @b{reset-halt-post}
@* Currently not usd
@item @b{reset-halt-pre}
@* Currently not used
@item @b{reset-init}
@* Used by @b{reset init} command for board-specific initialization.
+This event fires after @emph{reset-deassert-post}.
This is where you would configure PLLs and clocking, set up DRAM so
you can download programs that don't fit in on-chip SRAM, set up pin
multiplexing, and so on.
@item @b{reset-start}
-@* Currently not used
+@* Issued as part of @command{reset} processing
+before either SRST or TRST are activated.
@item @b{reset-wait-pos}
@* Currently not used
@item @b{reset-wait-pre}
@* Success
@item @b{resumed}
@* Target has resumed
-@item @b{tap-enable}
-@* Executed by @b{jtag tapenable DOTTED.NAME} command. Example:
-@example
-jtag configure DOTTED.NAME -event tap-enable @{
- puts "Enabling CPU"
- ...
-@}
-@end example
-@item @b{tap-disable}
-@*Executed by @b{jtag tapdisable DOTTED.NAME} command. Example:
-@example
-jtag configure DOTTED.NAME -event tap-disable @{
- puts "Disabling CPU"
- ...
-@}
-@end example
@end itemize
-@section Target Create
@anchor{Target Create}
+@section Target Create
@cindex target
@cindex target creation
@}
@end example
+@b{PROBLEM:} On more complex chips, the work area can become
+inaccessible when application code enables or disables the MMU.
+For example, the MMU context used to acess the virtual address
+will probably matter.
+
@section Target Variants
@itemize @bullet
@item @b{cortex_m3}
configuration command to enable OpenOCD hardware reset functionality.
@comment END variants
@end itemize
-@section working_area - Command Removed
-@cindex working_area
-@*@b{Please use the ``$_TARGETNAME configure -work-area-... parameters instead}
-@* This documentation remains because there are existing scripts that
-still use this that need to be converted.
-@example
- working_area target# address size backup| [virtualaddress]
-@end example
-@* The target# is a the 0 based target numerical index.
@node Flash Commands
@chapter Flash Commands
is that for read access, it acts exactly like any other addressible memory.
This means you can use normal memory read commands like @command{mdw} or
@command{dump_image} with it, with no special @command{flash} subcommands.
-@xref{Memory access}.
-@xref{Image access}.
+@xref{Memory access}, and @ref{Image access}.
Write access works differently. Flash memory normally needs to be erased
before it's written. Erasing a sector turns all of its bits to ones, and
@comment @option{flash erase_sector} using the same syntax.
@end deffn
-@section Flash Drivers, Options, and Commands
@anchor{Flash Driver List}
+@section Flash Drivers, Options, and Commands
As noted above, the @command{flash bank} command requires a driver name,
and allows driver-specific options and behaviors.
Some drivers also activate driver-specific commands.
@itemize
@item @var{jedec_probe} ... is used to detect certain non-CFI flash ROMs,
like AM29LV010 and similar types.
-@item @var{x16_as_x8} ...
+@item @var{x16_as_x8} ... when a 16-bit flash is hooked up to an 8-bit bus.
@end itemize
To configure two adjacent banks of 16 MBytes each, both sixteen bits (two bytes)
has been locked. Halting the core is not required for the @option{str9xpec} driver
as mentioned above, just issue the commands above manually or from a telnet prompt.
-@subsubsection str9xpec driver options
-
-@b{flash bank str9xpec} <@var{base}> <@var{size}> 0 0 <@var{target}>
-@*Before using the flash commands the turbo mode must be enabled using str9xpec
-@option{enable_turbo} <@var{num>.}
-
+@deffn {Flash Driver} str9xpec
Only use this driver for locking/unlocking the device or configuring the option bytes.
Use the standard str9 driver for programming.
+Before using the flash commands the turbo mode must be enabled using the
+@command{str9xpec enable_turbo} command.
-@subsubsection str9xpec specific commands
-@cindex str9xpec specific commands
-These are flash specific commands when using the str9xpec driver.
+Several str9xpec-specific commands are defined:
-@itemize @bullet
-@item @b{str9xpec enable_turbo} <@var{num}>
-@cindex str9xpec enable_turbo
-@*enable turbo mode, will simply remove the str9 from the chain and talk
+@deffn Command {str9xpec disable_turbo} num
+Restore the str9 into JTAG chain.
+@end deffn
+
+@deffn Command {str9xpec enable_turbo} num
+Enable turbo mode, will simply remove the str9 from the chain and talk
directly to the embedded flash controller.
-@item @b{str9xpec disable_turbo} <@var{num}>
-@cindex str9xpec disable_turbo
-@*restore the str9 into JTAG chain.
-@item @b{str9xpec lock} <@var{num}>
-@cindex str9xpec lock
-@*lock str9 device. The str9 will only respond to an unlock command that will
+@end deffn
+
+@deffn Command {str9xpec lock} num
+Lock str9 device. The str9 will only respond to an unlock command that will
erase the device.
-@item @b{str9xpec unlock} <@var{num}>
-@cindex str9xpec unlock
-@*unlock str9 device.
-@item @b{str9xpec options_read} <@var{num}>
-@cindex str9xpec options_read
-@*read str9 option bytes.
-@item @b{str9xpec options_write} <@var{num}>
-@cindex str9xpec options_write
-@*write str9 option bytes.
-@end itemize
+@end deffn
-@subsubsection STR9 option byte configuration
-@cindex STR9 option byte configuration
+@deffn Command {str9xpec part_id} num
+Prints the part identifier for bank @var{num}.
+@end deffn
+
+@deffn Command {str9xpec options_cmap} num (@option{bank0}|@option{bank1})
+Configure str9 boot bank.
+@end deffn
+
+@deffn Command {str9xpec options_lvdsel} num (@option{vdd}|@option{vdd_vddq})
+Configure str9 lvd source.
+@end deffn
+
+@deffn Command {str9xpec options_lvdthd} num (@option{2.4v}|@option{2.7v})
+Configure str9 lvd threshold.
+@end deffn
+
+@deffn Command {str9xpec options_lvdwarn} bank (@option{vdd}|@option{vdd_vddq})
+Configure str9 lvd reset warning source.
+@end deffn
+
+@deffn Command {str9xpec options_read} num
+Read str9 option bytes.
+@end deffn
+
+@deffn Command {str9xpec options_write} num
+Write str9 option bytes.
+@end deffn
+
+@deffn Command {str9xpec unlock} num
+unlock str9 device.
+@end deffn
+
+@end deffn
-@itemize @bullet
-@item @b{str9xpec options_cmap} <@var{num}> <@option{bank0}|@option{bank1}>
-@cindex str9xpec options_cmap
-@*configure str9 boot bank.
-@item @b{str9xpec options_lvdthd} <@var{num}> <@option{2.4v}|@option{2.7v}>
-@cindex str9xpec options_lvdthd
-@*configure str9 lvd threshold.
-@item @b{str9xpec options_lvdsel} <@var{num}> <@option{vdd}|@option{vdd_vddq}>
-@cindex str9xpec options_lvdsel
-@*configure str9 lvd source.
-@item @b{str9xpec options_lvdwarn} <@var{bank}> <@option{vdd}|@option{vdd_vddq}>
-@cindex str9xpec options_lvdwarn
-@*configure str9 lvd reset warning source.
-@end itemize
@section mFlash
@subsection mFlash Configuration
@cindex mFlash Configuration
-@b{mflash bank} <@var{soc}> <@var{base}> <@var{RST pin}> <@var{target}>
-@cindex mflash bank
-@*Configures a mflash for <@var{soc}> host bank at
-<@var{base}>. Pin number format is dependent on host GPIO calling convention.
-Currently, mflash bank support s3c2440 and pxa270.
-(ex. of s3c2440) mflash <@var{RST pin}> is GPIO B1.
+@deffn {Config Command} {mflash bank} soc base RST_pin target
+Configures a mflash for @var{soc} host bank at
+address @var{base}.
+The pin number format depends on the host GPIO naming convention.
+Currently, the mflash driver supports s3c2440 and pxa270.
+
+Example for s3c2440 mflash where @var{RST pin} is GPIO B1:
@example
mflash bank s3c2440 0x10000000 1b 0
@end example
-(ex. of pxa270) mflash <@var{RST pin}> is GPIO 43.
+Example for pxa270 mflash where @var{RST pin} is GPIO 43:
@example
mflash bank pxa270 0x08000000 43 0
@end example
+@end deffn
@subsection mFlash commands
@cindex mFlash commands
-@itemize @bullet
-@item @b{mflash probe}
-@cindex mflash probe
-@*Probe mflash.
-@item @b{mflash write} <@var{num}> <@var{file}> <@var{offset}>
-@cindex mflash write
-@*Write the binary <@var{file}> to mflash bank <@var{num}>, starting at
-<@var{offset}> bytes from the beginning of the bank.
-@item @b{mflash dump} <@var{num}> <@var{file}> <@var{offset}> <@var{size}>
-@cindex mflash dump
-@*Dump <size> bytes, starting at <@var{offset}> bytes from the beginning of the <@var{num}> bank
-to a <@var{file}>.
-@item @b{mflash config pll} <@var{frequency}>
-@cindex mflash config pll
-@*Configure mflash pll. <@var{frequency}> is input frequency of mflash. The order is Hz.
+@deffn Command {mflash config pll} frequency
+Configure mflash PLL.
+The @var{frequency} is the mflash input frequency, in Hz.
Issuing this command will erase mflash's whole internal nand and write new pll.
After this command, mflash needs power-on-reset for normal operation.
If pll was newly configured, storage and boot(optional) info also need to be update.
-@item @b{mflash config boot}
-@cindex mflash config boot
-@*Configure bootable option. If bootable option is set, mflash offer the first 8 sectors
+@end deffn
+
+@deffn Command {mflash config boot}
+Configure bootable option.
+If bootable option is set, mflash offer the first 8 sectors
(4kB) for boot.
-@item @b{mflash config storage}
-@cindex mflash config storage
-@*Configure storage information. For the normal storage operation, this information must be
+@end deffn
+
+@deffn Command {mflash config storage}
+Configure storage information.
+For the normal storage operation, this information must be
written.
-@end itemize
+@end deffn
+
+@deffn Command {mflash dump} num filename offset size
+Dump @var{size} bytes, starting at @var{offset} bytes from the
+beginning of the bank @var{num}, to the file named @var{filename}.
+@end deffn
+
+@deffn Command {mflash probe}
+Probe mflash.
+@end deffn
+
+@deffn Command {mflash write} num filename offset
+Write the binary file @var{filename} to mflash bank @var{num}, starting at
+@var{offset} bytes from the beginning of the bank.
+@end deffn
@node NAND Flash Commands
@chapter NAND Flash Commands
status for each block.
@end deffn
-@deffn Command {nand raw_access} num <enable|disable>
+@deffn Command {nand raw_access} num (@option{enable}|@option{disable})
Sets or clears an flag affecting how page I/O is done.
The @var{num} parameter is the value shown by @command{nand list}.
with the wrong ECC data can cause them to be marked as bad.
@end deffn
-@section NAND Drivers, Options, and Commands
@anchor{NAND Driver List}
+@section NAND Drivers, Options, and Commands
As noted above, the @command{nand device} command allows
driver-specific options and behaviors.
Some controllers also activate controller-specific commands.
@section Daemon Commands
-@subsection sleep [@var{msec}]
-@cindex sleep
-@*Wait for n milliseconds before resuming. Useful in connection with script files
-(@var{script} command and @var{target_script} configuration).
+@deffn Command sleep msec [@option{busy}]
+Wait for at least @var{msec} milliseconds before resuming.
+If @option{busy} is passed, busy-wait instead of sleeping.
+(This option is strongly discouraged.)
+Useful in connection with script files
+(@command{script} command and @command{target_name} configuration).
+@end deffn
-@subsection shutdown
-@cindex shutdown
-@*Close the OpenOCD daemon, disconnecting all clients (GDB, telnet, other).
+@deffn Command shutdown
+Close the OpenOCD daemon, disconnecting all clients (GDB, telnet, other).
+@end deffn
-@subsection debug_level [@var{n}]
-@cindex debug_level
@anchor{debug_level}
-@*Display or adjust debug level to n<0-3>
+@deffn Command debug_level [n]
+@cindex message level
+Display debug level.
+If @var{n} (from 0..3) is provided, then set it to that level.
+This affects the kind of messages sent to the server log.
+Level 0 is error messages only;
+level 1 adds warnings;
+level 2 (the default) adds informational messages;
+and level 3 adds debugging messages.
+@end deffn
+
+@deffn Command fast (@option{enable}|@option{disable})
+Default disabled.
+Set default behaviour of OpenOCD to be "fast and dangerous".
-@subsection fast [@var{enable|disable}]
-@cindex fast
-@*Default disabled. Set default behaviour of OpenOCD to be "fast and dangerous". For instance ARM7/9 DCC memory
-downloads and fast memory access will work if the JTAG interface isn't too fast and
-the core doesn't run at a too low frequency. Note that this option only changes the default
-and that the indvidual options, like DCC memory downloads, can be enabled and disabled
-individually.
+At this writing, this only affects the defaults for two ARM7/ARM9 parameters:
+fast memory access, and DCC downloads. Those parameters may still be
+individually overridden.
The target specific "dangerous" optimisation tweaking options may come and go
as more robust and user friendly ways are found to ensure maximum throughput
@example
openocd -c "fast enable" -c "interface dummy" -f target/str710.cfg
@end example
+@end deffn
-@subsection echo <@var{message}>
-@cindex echo
-@*Output message to stdio. e.g. echo "Programming - please wait"
+@deffn Command echo message
+Logs a message at "user" priority.
+Output @var{message} to stdout.
+@example
+echo "Downloading kernel -- please wait"
+@end example
+@end deffn
-@subsection log_output <@var{file}>
-@cindex log_output
-@*Redirect logging to <file> (default: stderr)
+@deffn Command log_output [filename]
+Redirect logging to @var{filename};
+the initial log output channel is stderr.
+@end deffn
-@subsection script <@var{file}>
-@cindex script
-@*Execute commands from <file>
-See also: ``source [find FILENAME]''
+@section Target State handling
+@cindex reset
+@cindex halt
+@cindex target initialization
-@section Target state handling
-@subsection power <@var{on}|@var{off}>
-@cindex reg
-@*Turn power switch to target on/off.
-No arguments: print status.
-Not all interfaces support this.
-
-@subsection reg [@option{#}|@option{name}] [value]
-@cindex reg
-@*Access a single register by its number[@option{#}] or by its [@option{name}].
-No arguments: list all available registers for the current target.
-Number or name argument: display a register.
-Number or name and value arguments: set register value.
-
-@subsection poll [@option{on}|@option{off}]
-@cindex poll
-@*Poll the target for its current state. If the target is in debug mode, architecture
+In this section ``target'' refers to a CPU configured as
+shown earlier (@pxref{CPU Configuration}).
+These commands, like many, implicitly refer to
+a @dfn{current target} which is used to perform the
+various operations. The current target may be changed
+by using @command{targets} command with the name of the
+target which should become current.
+
+@deffn Command reg [(number|name) [value]]
+Access a single register by @var{number} or by its @var{name}.
+
+@emph{With no arguments}:
+list all available registers for the current target,
+showing number, name, size, value, and cache status.
+
+@emph{With number/name}: display that register's value.
+
+@emph{With both number/name and value}: set register's value.
+
+Cores may have surprisingly many registers in their
+Debug and trace infrastructure:
+
+@example
+> reg
+(0) r0 (/32): 0x0000D3C2 (dirty: 1, valid: 1)
+(1) r1 (/32): 0xFD61F31C (dirty: 0, valid: 1)
+(2) r2 (/32): 0x00022551 (dirty: 0, valid: 1)
+...
+(164) ETM_CONTEXTID_COMPARATOR_MASK (/32): \
+ 0x00000000 (dirty: 0, valid: 0)
+>
+@end example
+@end deffn
+
+@deffn Command poll [@option{on}|@option{off}]
+Poll the current target for its current state.
+If that target is in debug mode, architecture
specific information about the current state is printed. An optional parameter
allows continuous polling to be enabled and disabled.
-@subsection halt [@option{ms}]
-@cindex halt
-@*Send a halt request to the target and wait for it to halt for up to [@option{ms}] milliseconds.
-Default [@option{ms}] is 5 seconds if no arg given.
-Optional arg @option{ms} is a timeout in milliseconds. Using 0 as the [@option{ms}]
-will stop OpenOCD from waiting.
-
-@subsection wait_halt [@option{ms}]
-@cindex wait_halt
-@*Wait for the target to enter debug mode. Optional [@option{ms}] is
-a timeout in milliseconds. Default [@option{ms}] is 5 seconds if no
-arg is given.
-
-@subsection resume [@var{address}]
-@cindex resume
-@*Resume the target at its current code position, or at an optional address.
+@example
+> poll
+target state: halted
+target halted in ARM state due to debug-request, \
+ current mode: Supervisor
+cpsr: 0x800000d3 pc: 0x11081bfc
+MMU: disabled, D-Cache: disabled, I-Cache: enabled
+>
+@end example
+@end deffn
+
+@deffn Command halt [ms]
+@deffnx Command wait_halt [ms]
+The @command{halt} command first sends a halt request to the target,
+which @command{wait_halt} doesn't.
+Otherwise these behave the same: wait up to @var{ms} milliseconds,
+or 5 seconds if there is no parameter, for the target to halt
+(and enter debug mode).
+Using 0 as the @var{ms} parameter prevents OpenOCD from waiting.
+@end deffn
+
+@deffn Command resume [address]
+Resume the target at its current code position,
+or the optional @var{address} if it is provided.
OpenOCD will wait 5 seconds for the target to resume.
+@end deffn
-@subsection step [@var{address}]
-@cindex step
-@*Single-step the target at its current code position, or at an optional address.
+@deffn Command step [address]
+Single-step the target at its current code position,
+or the optional @var{address} if it is provided.
+@end deffn
@anchor{Reset Command}
-@subsection reset [@option{run}|@option{halt}|@option{init}]
-@cindex reset
-@*Perform a hard-reset. The optional parameter specifies what should
+@deffn Command reset
+@deffnx Command {reset run}
+@deffnx Command {reset halt}
+@deffnx Command {reset init}
+Perform as hard a reset as possible, using SRST if possible.
+@emph{All defined targets will be reset, and target
+events will fire during the reset sequence.}
+
+The optional parameter specifies what should
happen after the reset.
If there is no parameter, a @command{reset run} is executed.
The other options will not work on all systems.
@xref{Reset Configuration}.
+
@itemize @minus
-@item @b{run}
-@cindex reset run
-@*Let the target run.
-@item @b{halt}
-@cindex reset halt
-@*Immediately halt the target (works only with certain configurations).
-@item @b{init}
-@cindex reset init
-@*Immediately halt the target, and execute the reset script (works only with certain
-configurations)
+@item @b{run} Let the target run
+@item @b{halt} Immediately halt the target
+@item @b{init} Immediately halt the target, and execute the reset-init script
@end itemize
+@end deffn
-@subsection soft_reset_halt
-@cindex reset
-@*Requesting target halt and executing a soft reset. This is often used
+@deffn Command soft_reset_halt
+Requesting target halt and executing a soft reset. This is often used
when a target cannot be reset and halted. The target, after reset is
released begins to execute code. OpenOCD attempts to stop the CPU and
then sets the program counter back to the reset vector. Unfortunately
the code that was executed may have left the hardware in an unknown
state.
+@end deffn
+@section I/O Utilities
+
+These commands are available when
+OpenOCD is built with @option{--enable-ioutil}.
+They are mainly useful on embedded targets;
+PC type hosts have complimentary tools.
+
+@emph{Note:} there are several more such commands.
+
+@deffn Command meminfo
+Display available RAM memory on OpenOCD host.
+Used in OpenOCD regression testing scripts.
+@end deffn
-@section Memory access commands
@anchor{Memory access}
-@subsection meminfo
-display available RAM memory.
-@subsection Memory peek/poke type commands
+@section Memory access commands
+@cindex memory access
+
These commands allow accesses of a specific size to the memory
system. Often these are used to configure the current target in some
-special way. For example - one may need to write certian values to the
+special way. For example - one may need to write certain values to the
SDRAM controller to enable SDRAM.
@enumerate
-@item To change the current target see the ``targets'' (plural) command
-@item In system level scripts these commands are deprecated, please use the TARGET object versions.
+@item Use the @command{targets} (plural) command
+to change the current target.
+@item In system level scripts these commands are deprecated.
+Please use their TARGET object siblings to avoid making assumptions
+about what TAP is the current target, or about MMU configuration.
@end enumerate
-@itemize @bullet
-@item @b{mdw} <@var{addr}> [@var{count}]
-@cindex mdw
-@*display memory words (32bit)
-@item @b{mdh} <@var{addr}> [@var{count}]
-@cindex mdh
-@*display memory half-words (16bit)
-@item @b{mdb} <@var{addr}> [@var{count}]
-@cindex mdb
-@*display memory bytes (8bit)
-@item @b{mww} <@var{addr}> <@var{value}>
-@cindex mww
-@*write memory word (32bit)
-@item @b{mwh} <@var{addr}> <@var{value}>
-@cindex mwh
-@*write memory half-word (16bit)
-@item @b{mwb} <@var{addr}> <@var{value}>
-@cindex mwb
-@*write memory byte (8bit)
-@end itemize
+@deffn Command mdw addr [count]
+@deffnx Command mdh addr [count]
+@deffnx Command mdb addr [count]
+Display contents of address @var{addr}, as
+32-bit words (@command{mdw}), 16-bit halfwords (@command{mdh}),
+or 8-bit bytes (@command{mdb}).
+If @var{count} is specified, displays that many units.
+@end deffn
+
+@deffn Command mww addr word
+@deffnx Command mwh addr halfword
+@deffnx Command mwb addr byte
+Writes the specified @var{word} (32 bits),
+@var{halfword} (16 bits), or @var{byte} (8-bit) pattern,
+at the specified address @var{addr}.
+@end deffn
+
-@section Image loading commands
@anchor{Image access}
-@subsection load_image
-@b{load_image} <@var{file}> <@var{address}> [@option{bin}|@option{ihex}|@option{elf}]
-@cindex load_image
-@anchor{load_image}
-@*Load image <@var{file}> to target memory at <@var{address}>
-@subsection fast_load_image
-@b{fast_load_image} <@var{file}> <@var{address}> [@option{bin}|@option{ihex}|@option{elf}]
-@cindex fast_load_image
-@anchor{fast_load_image}
-@*Normally you should be using @b{load_image} or GDB load. However, for
+@section Image loading commands
+@cindex image loading
+@cindex image dumping
+
+@anchor{dump_image}
+@deffn Command {dump_image} filename address size
+Dump @var{size} bytes of target memory starting at @var{address} to the
+binary file named @var{filename}.
+@end deffn
+
+@deffn Command {fast_load}
+Loads an image stored in memory by @command{fast_load_image} to the
+current target. Must be preceeded by fast_load_image.
+@end deffn
+
+@deffn Command {fast_load_image} filename address [@option{bin}|@option{ihex}|@option{elf}]
+Normally you should be using @command{load_image} or GDB load. However, for
testing purposes or when I/O overhead is significant(OpenOCD running on an embedded
host), storing the image in memory and uploading the image to the target
can be a way to upload e.g. multiple debug sessions when the binary does not change.
-Arguments are the same as @b{load_image}, but the image is stored in OpenOCD host
+Arguments are the same as @command{load_image}, but the image is stored in OpenOCD host
memory, i.e. does not affect target. This approach is also useful when profiling
target programming performance as I/O and target programming can easily be profiled
separately.
-@subsection fast_load
-@b{fast_load}
-@cindex fast_image
-@anchor{fast_image}
-@*Loads an image stored in memory by @b{fast_load_image} to the current target. Must be preceeded by fast_load_image.
-@subsection dump_image
-@b{dump_image} <@var{file}> <@var{address}> <@var{size}>
-@cindex dump_image
-@anchor{dump_image}
-@*Dump <@var{size}> bytes of target memory starting at <@var{address}> to a
-(binary) <@var{file}>.
-@subsection verify_image
-@b{verify_image} <@var{file}> <@var{address}> [@option{bin}|@option{ihex}|@option{elf}]
-@cindex verify_image
-@*Verify <@var{file}> against target memory starting at <@var{address}>.
+@end deffn
+
+@anchor{load_image}
+@deffn Command {load_image} filename address [@option{bin}|@option{ihex}|@option{elf}]
+Load image from file @var{filename} to target memory at @var{address}.
+The file format may optionally be specified
+(@option{bin}, @option{ihex}, or @option{elf})
+@end deffn
+
+@deffn Command {verify_image} filename address [@option{bin}|@option{ihex}|@option{elf}]
+Verify @var{filename} against target memory starting at @var{address}.
+The file format may optionally be specified
+(@option{bin}, @option{ihex}, or @option{elf})
This will first attempt a comparison using a CRC checksum, if this fails it will try a binary compare.
+@end deffn
-@section Breakpoint commands
-@cindex Breakpoint commands
-@itemize @bullet
-@item @b{bp} <@var{addr}> <@var{len}> [@var{hw}]
-@cindex bp
-@*set breakpoint <address> <length> [hw]
-@item @b{rbp} <@var{addr}>
-@cindex rbp
-@*remove breakpoint <adress>
-@item @b{wp} <@var{addr}> <@var{len}> <@var{r}|@var{w}|@var{a}> [@var{value}] [@var{mask}]
-@cindex wp
-@*set watchpoint <address> <length> <r/w/a> [value] [mask]
-@item @b{rwp} <@var{addr}>
-@cindex rwp
-@*remove watchpoint <adress>
-@end itemize
+@section Breakpoint and Watchpoint commands
+@cindex breakpoint
+@cindex watchpoint
-@section Misc Commands
-@cindex Other Target Commands
-@itemize
-@item @b{profile} <@var{seconds}> <@var{gmon.out}>
+CPUs often make debug modules accessible through JTAG, with
+hardware support for a handful of code breakpoints and data
+watchpoints.
+In addition, CPUs almost always support software breakpoints.
-Profiling samples the CPU's program counter as quickly as possible, which is useful for non-intrusive stochastic profiling.
+@deffn Command {bp} [address len [@option{hw}]]
+With no parameters, lists all active breakpoints.
+Else sets a breakpoint on code execution starting
+at @var{address} for @var{length} bytes.
+This is a software breakpoint, unless @option{hw} is specified
+in which case it will be a hardware breakpoint.
+@end deffn
-@end itemize
+@deffn Command {rbp} address
+Remove the breakpoint at @var{address}.
+@end deffn
+
+@deffn Command {rwp} address
+Remove data watchpoint on @var{address}
+@end deffn
+
+@deffn Command {wp} [address len [(@option{r}|@option{w}|@option{a}) [value [mask]]]
+With no parameters, lists all active watchpoints.
+Else sets a data watchpoint on data from @var{address} for @var{length} bytes.
+The watch point is an "access" watchpoint unless
+the @option{r} or @option{w} parameter is provided,
+defining it as respectively a read or write watchpoint.
+If a @var{value} is provided, that value is used when determining if
+the watchpoint should trigger. The value may be first be masked
+using @var{mask} to mark ``don't care'' fields.
+@end deffn
+
+@section Misc Commands
+@cindex profiling
+
+@deffn Command {profile} seconds filename
+Profiling samples the CPU's program counter as quickly as possible,
+which is useful for non-intrusive stochastic profiling.
+Saves up to 10000 sampines in @file{filename} using ``gmon.out'' format.
+@end deffn
-@section Architecture and Core Specific Commands
+@node Architecture and Core Commands
+@chapter Architecture and Core Commands
@cindex Architecture Specific Commands
@cindex Core Specific Commands
Most CPUs have specialized JTAG operations to support debugging.
OpenOCD packages most such operations in its standard command framework.
Some of those operations don't fit well in that framework, so they are
-exposed here using architecture or implementation specific commands.
+exposed here as architecture or implementation (core) specific commands.
+
+@anchor{ARM Tracing}
+@section ARM Tracing
+@cindex ETM
+@cindex ETB
+
+CPUs based on ARM cores may include standard tracing interfaces,
+based on an ``Embedded Trace Module'' (ETM) which sends voluminous
+address and data bus trace records to a ``Trace Port''.
+
+@itemize
+@item
+Development-oriented boards will sometimes provide a high speed
+trace connector for collecting that data, when the particular CPU
+supports such an interface.
+(The standard connector is a 38-pin Mictor, with both JTAG
+and trace port support.)
+Those trace connectors are supported by higher end JTAG adapters
+and some logic analyzer modules; frequently those modules can
+buffer several megabytes of trace data.
+Configuring an ETM coupled to such an external trace port belongs
+in the board-specific configuration file.
+@item
+If the CPU doesn't provide an external interface, it probably
+has an ``Embedded Trace Buffer'' (ETB) on the chip, which is a
+dedicated SRAM. 4KBytes is one common ETB size.
+Configuring an ETM coupled only to an ETB belongs in the CPU-specific
+(target) configuration file, since it works the same on all boards.
+@end itemize
+
+ETM support in OpenOCD doesn't seem to be widely used yet.
+
+@quotation Issues
+ETM support may be buggy, and at least some @command{etm config}
+parameters should be detected by asking the ETM for them.
+It seems like a GDB hookup should be possible,
+as well as triggering trace on specific events
+(perhaps @emph{handling IRQ 23} or @emph{calls foo()}).
+There should be GUI tools to manipulate saved trace data and help
+analyse it in conjunction with the source code.
+It's unclear how much of a common interface is shared
+with the current XScale trace support, or should be
+shared with eventual Nexus-style trace module support.
+@end quotation
+
+@subsection ETM Configuration
+ETM setup is coupled with the trace port driver configuration.
+
+@deffn {Config Command} {etm config} target width mode clocking driver
+Declares the ETM associated with @var{target}, and associates it
+with a given trace port @var{driver}. @xref{Trace Port Drivers}.
+
+Several of the parameters must reflect the trace port configuration.
+The @var{width} must be either 4, 8, or 16.
+The @var{mode} must be @option{normal}, @option{multiplexted},
+or @option{demultiplexted}.
+The @var{clocking} must be @option{half} or @option{full}.
+
+@quotation Note
+You can see the ETM registers using the @command{reg} command, although
+not all of those possible registers are present in every ETM.
+@end quotation
+@end deffn
+
+@deffn Command {etm info}
+Displays information about the current target's ETM.
+@end deffn
+
+@deffn Command {etm status}
+Displays status of the current target's ETM:
+is the ETM idle, or is it collecting data?
+Did trace data overflow?
+Was it triggered?
+@end deffn
+
+@deffn Command {etm tracemode} [type context_id_bits cycle_accurate branch_output]
+Displays what data that ETM will collect.
+If arguments are provided, first configures that data.
+When the configuration changes, tracing is stopped
+and any buffered trace data is invalidated.
+
+@itemize
+@item @var{type} ... one of
+@option{none} (save nothing),
+@option{data} (save data),
+@option{address} (save addresses),
+@option{all} (save data and addresses)
+@item @var{context_id_bits} ... 0, 8, 16, or 32
+@item @var{cycle_accurate} ... @option{enable} or @option{disable}
+@item @var{branch_output} ... @option{enable} or @option{disable}
+@end itemize
+@end deffn
+
+@deffn Command {etm trigger_percent} percent
+@emph{Buggy and effectively a NOP ... @var{percent} from 2..100}
+@end deffn
+
+@subsection ETM Trace Operation
+
+After setting up the ETM, you can use it to collect data.
+That data can be exported to files for later analysis.
+It can also be parsed with OpenOCD, for basic sanity checking.
+
+@deffn Command {etm analyze}
+Reads trace data into memory, if it wasn't already present.
+Decodes and prints the data that was collected.
+@end deffn
+
+@deffn Command {etm dump} filename
+Stores the captured trace data in @file{filename}.
+@end deffn
+
+@deffn Command {etm image} filename [base_address] [type]
+Opens an image file.
+@end deffn
+
+@deffn Command {etm load} filename
+Loads captured trace data from @file{filename}.
+@end deffn
+
+@deffn Command {etm start}
+Starts trace data collection.
+@end deffn
+
+@deffn Command {etm stop}
+Stops trace data collection.
+@end deffn
+
+@anchor{Trace Port Drivers}
+@subsection Trace Port Drivers
+
+To use an ETM trace port it must be associated with a driver.
+
+@deffn {Trace Port Driver} dummy
+Use the @option{dummy} driver if you are configuring an ETM that's
+not connected to anything (on-chip ETB or off-chip trace connector).
+@emph{This driver lets OpenOCD talk to the ETM, but it does not expose
+any trace data collection.}
+@deffn {Config Command} {etm_dummy config} target
+Associates the ETM for @var{target} with a dummy driver.
+@end deffn
+@end deffn
+
+@deffn {Trace Port Driver} etb
+Use the @option{etb} driver if you are configuring an ETM
+to use on-chip ETB memory.
+@deffn {Config Command} {etb config} target etb_tap
+Associates the ETM for @var{target} with the ETB at @var{etb_tap}.
+You can see the ETB registers using the @command{reg} command.
+@end deffn
+@end deffn
+
+@deffn {Trace Port Driver} oocd_trace
+This driver isn't available unless OpenOCD was explicitly configured
+with the @option{--enable-oocd_trace} option. You probably don't want
+to configure it unless you've built the appropriate prototype hardware;
+it's @emph{proof-of-concept} software.
+
+Use the @option{oocd_trace} driver if you are configuring an ETM that's
+connected to an off-chip trace connector.
+
+@deffn {Config Command} {oocd_trace config} target tty
+Associates the ETM for @var{target} with a trace driver which
+collects data through the serial port @var{tty}.
+@end deffn
+
+@deffn Command {oocd_trace resync}
+Re-synchronizes with the capture clock.
+@end deffn
-@subsection ARMv4 and ARMv5 Architecture
-@cindex ARMv4 specific commands
-@cindex ARMv5 specific commands
+@deffn Command {oocd_trace status}
+Reports whether the capture clock is locked or not.
+@end deffn
+@end deffn
+
+
+@section ARMv4 and ARMv5 Architecture
+@cindex ARMv4
+@cindex ARMv5
These commands are specific to ARM architecture v4 and v5,
including all ARM7 or ARM9 systems and Intel XScale.
They are available in addition to other core-specific
commands that may be available.
-@deffn Command {armv4_5 core_state} [arm|thumb]
+@deffn Command {armv4_5 core_state} [@option{arm}|@option{thumb}]
Displays the core_state, optionally changing it to process
either @option{arm} or @option{thumb} instructions.
The target may later be resumed in the currently set core_state.
@end deffn
@deffn Command {armv4_5 reg}
-Display a list of all banked core registers, fetching the current value from every
+Display a table of all banked core registers, fetching the current value from every
core mode if necessary. OpenOCD versions before rev. 60 didn't fetch the current
register value.
@end deffn
-@subsubsection ARM7 and ARM9 specific commands
-@cindex ARM7 specific commands
-@cindex ARM9 specific commands
+@subsection ARM7 and ARM9 specific commands
+@cindex ARM7
+@cindex ARM9
These commands are specific to ARM7 and ARM9 cores, like ARM7TDMI, ARM720T,
ARM9TDMI, ARM920T or ARM926EJ-S.
They are available in addition to the ARMv4/5 commands,
and any other core-specific commands that may be available.
-@deffn Command {arm7_9 dbgrq} (enable|disable)
+@deffn Command {arm7_9 dbgrq} (@option{enable}|@option{disable})
Control use of the EmbeddedIce DBGRQ signal to force entry into debug mode,
instead of breakpoints. This should be
safe for all but ARM7TDMI--S cores (like Philips LPC).
@end deffn
-@deffn Command {arm7_9 dcc_downloads} (enable|disable)
+@deffn Command {arm7_9 dcc_downloads} (@option{enable}|@option{disable})
@cindex DCC
Control the use of the debug communications channel (DCC) to write larger (>128 byte)
amounts of memory. DCC downloads offer a huge speed increase, but might be
@end deffn
@anchor{arm7_9 fast_memory_access}
-@deffn Command {arm7_9 fast_memory_access} (enable|disable)
+@deffn Command {arm7_9 fast_memory_access} (@option{enable}|@option{disable})
Enable or disable memory writes and reads that don't check completion of
the operation. This provides a huge speed increase, especially with USB JTAG
cables (FT2232), but might be unsafe if used with targets running at very low
The write goes directly to the CPU, bypassing the register cache.
@end deffn
-@deffn {Debug Command} {arm7_9 write_xpsr} word (0|1)
+@deffn {Debug Command} {arm7_9 write_xpsr} word (@option{0}|@option{1})
@emph{This is intended for use while debugging OpenOCD; you probably
shouldn't use it.}
In both cases, this bypasses the register cache.
@end deffn
-@deffn {Debug Command} {arm7_9 write_xpsr_im8} byte rotate (0|1)
+@deffn {Debug Command} {arm7_9 write_xpsr_im8} byte rotate (@option{0}|@option{1})
@emph{This is intended for use while debugging OpenOCD; you probably
shouldn't use it.}
with @command{arm7_9 write_xpsr}.
@end deffn
-@subsubsection ARM720T specific commands
-@cindex ARM720T specific commands
+@subsection ARM720T specific commands
+@cindex ARM720T
These commands are available to ARM720T based CPUs,
which are implementations of the ARMv4T architecture
and display the result.
@end deffn
-@subsubsection ARM9TDMI specific commands
-@cindex ARM9TDMI specific commands
+@subsection ARM9TDMI specific commands
+@cindex ARM9TDMI
Many ARM9-family CPUs are built around ARM9TDMI integer cores,
or processors resembling ARM9TDMI, and can use these commands.
Such cores include the ARM920T, ARM926EJ-S, and ARM966.
-@deffn Command {arm9tdmi vector_catch} (all|none|list)
+@deffn Command {arm9tdmi vector_catch} (@option{all}|@option{none}|list)
Catch arm9 interrupt vectors, can be @option{all}, @option{none},
or a list with one or more of the following:
@option{reset} @option{undef} @option{swi} @option{pabt} @option{dabt} @option{reserved}
@option{irq} @option{fiq}.
@end deffn
-@subsubsection ARM920T specific commands
-@cindex ARM920T specific commands
+@subsection ARM920T specific commands
+@cindex ARM920T
These commands are available to ARM920T based CPUs,
which are implementations of the ARMv4T architecture
Dump the content of the ITLB and DTLB to a file named @file{filename}.
@end deffn
-@deffn Command {arm920t virt2phys} @var{va}
+@deffn Command {arm920t virt2phys} va
Translate a virtual address @var{va} to a physical address
and display the result.
@end deffn
-@subsubsection ARM926EJ-S specific commands
-@cindex ARM926EJ-S specific commands
+@subsection ARM926ej-s specific commands
+@cindex ARM926ej-s
-These commands are available to ARM926EJ-S based CPUs,
+These commands are available to ARM926ej-s based CPUs,
which are implementations of the ARMv5TEJ architecture
based on the ARM9EJ-S integer core.
They are available in addition to the ARMv4/5, ARM7/ARM9,
at the specified physical address @var{addr}.
@end deffn
-@deffn Command {arm926ejs virt2phys} @var{va}
+@deffn Command {arm926ejs virt2phys} va
Translate a virtual address @var{va} to a physical address
and display the result.
@end deffn
-@subsubsection ARM966E specific commands
-@cindex ARM966E specific commands
+@subsection ARM966E specific commands
+@cindex ARM966E
These commands are available to ARM966 based CPUs,
which are implementations of the ARMv5TE architecture.
else if a @var{value} is provided, that value is written to that register.
@end deffn
-@subsubsection XScale specific commands
-@cindex XScale specific commands
+@subsection XScale specific commands
+@cindex XScale
These commands are available to XScale based CPUs,
which are implementations of the ARMv5TE architecture.
Changes the address used for the specified target's debug handler.
@end deffn
-@deffn Command {xscale dcache} (enable|disable)
+@deffn Command {xscale dcache} (@option{enable}|@option{disable})
Enables or disable the CPU's data cache.
@end deffn
Dumps the raw contents of the trace buffer to @file{filename}.
@end deffn
-@deffn Command {xscale icache} (enable|disable)
+@deffn Command {xscale icache} (@option{enable}|@option{disable})
Enables or disable the CPU's instruction cache.
@end deffn
-@deffn Command {xscale mmu} (enable|disable)
+@deffn Command {xscale mmu} (@option{enable}|@option{disable})
Enables or disable the CPU's memory management unit.
@end deffn
-@deffn Command {xscale trace_buffer} (enable|disable) [fill [n] | wrap]
+@deffn Command {xscale trace_buffer} (@option{enable}|@option{disable}) [@option{fill} [n] | @option{wrap}]
Enables or disables the trace buffer,
and controls how it is emptied.
@end deffn
Provide a bitmask showing the vectors to catch.
@end deffn
-@subsection ARMv6 Architecture
+@section ARMv6 Architecture
+@cindex ARMv6
-@subsubsection ARM11 specific commands
-@cindex ARM11 specific commands
+@subsection ARM11 specific commands
+@cindex ARM11
@deffn Command {arm11 mcr} p1 p2 p3 p4 p5
Read coprocessor register
If @var{value} is defined, first assigns that.
@end deffn
-@subsection ARMv7 Architecture
+@section ARMv7 Architecture
+@cindex ARMv7
+
+@subsection ARMv7 Debug Access Port (DAP) specific commands
+@cindex Debug Access Port
+@cindex DAP
+These commands are specific to ARM architecture v7 Debug Access Port (DAP),
+included on cortex-m3 and cortex-a8 systems.
+They are available in addition to other core-specific commands that may be available.
+
+@deffn Command {dap info} [num]
+Displays dap info for ap @var{num}, defaulting to the currently selected AP.
+@end deffn
+
+@deffn Command {dap apsel} [num]
+Select AP @var{num}, defaulting to 0.
+@end deffn
+
+@deffn Command {dap apid} [num]
+Displays id register from AP @var{num},
+defaulting to the currently selected AP.
+@end deffn
+
+@deffn Command {dap baseaddr} [num]
+Displays debug base address from AP @var{num},
+defaulting to the currently selected AP.
+@end deffn
+
+@deffn Command {dap memaccess} [value]
+Displays the number of extra tck for mem-ap memory bus access [0-255].
+If @var{value} is defined, first assigns that.
+@end deffn
-@subsubsection Cortex-M3 specific commands
-@cindex Cortex-M3 specific commands
+@subsection Cortex-M3 specific commands
+@cindex Cortex-M3
-@deffn Command {cortex_m3 maskisr} (on|off)
+@deffn Command {cortex_m3 maskisr} (@option{on}|@option{off})
Control masking (disabling) interrupts during target step/resume.
@end deffn
depends on CONFIG_DEBUG_LL) which uses this mechanism to
deliver messages before a serial console can be activated.
-@deffn Command {target_request debugmsgs} [enable|disable|charmsg]
+@deffn Command {target_request debugmsgs} [@option{enable}|@option{disable}|@option{charmsg}]
Displays current handling of target DCC message requests.
These messages may be sent to the debugger while the target is running.
-The optional @option{enable} and @option{charmsg} parameters are
-equivalent; both enable the messages, @option{disable} disables them.
+The optional @option{enable} and @option{charmsg} parameters
+both enable the messages, while @option{disable} disables them.
+With @option{charmsg} the DCC words each contain one character,
+as used by Linux with CONFIG_DEBUG_ICEDCC;
+otherwise the libdcc format is used.
@end deffn
@node JTAG Commands
@chapter JTAG Commands
@cindex JTAG Commands
-Generally most people will not use the bulk of these commands. They
-are mostly used by the OpenOCD developers or those who need to
-directly manipulate the JTAG taps.
-
-In general these commands control JTAG taps at a very low level. For
-example if you need to control a JTAG Route Controller (i.e.: the
-OMAP3530 on the Beagle Board has one) you might use these commands in
-a script or an event procedure.
-@section Commands
-@cindex Commands
+Most general purpose JTAG commands have been presented earlier.
+(@xref{JTAG Speed}, @ref{Reset Configuration}, and @ref{TAP Declaration}.)
+Lower level JTAG commands, as presented here,
+may be needed to work with targets which require special
+attention during operations such as reset or initialization.
+
+To use these commands you will need to understand some
+of the basics of JTAG, including:
+
@itemize @bullet
-@item @b{scan_chain}
-@cindex scan_chain
-@*Print current scan chain configuration.
-@item @b{jtag_reset} <@var{trst}> <@var{srst}>
-@cindex jtag_reset
-@*Toggle reset lines.
-@item @b{endstate} <@var{tap_state}>
-@cindex endstate
-@*Finish JTAG operations in <@var{tap_state}>.
-@item @b{runtest} <@var{num_cycles}>
-@cindex runtest
-@*Move to Run-Test/Idle, and execute <@var{num_cycles}>
-@item @b{statemove} [@var{tap_state}]
-@cindex statemove
-@*Move to current endstate or [@var{tap_state}]
-@item @b{irscan} <@var{device}> <@var{instr}> [@var{dev2}] [@var{instr2}] ...
-@cindex irscan
-@*Execute IR scan <@var{device}> <@var{instr}> [@var{dev2}] [@var{instr2}] ...
-@item @b{drscan} <@var{device}> [@var{dev2}] [@var{var2}] ...
-@cindex drscan
-@*Execute DR scan <@var{device}> [@var{dev2}] [@var{var2}] ...
-@item @b{verify_ircapture} <@option{enable}|@option{disable}>
-@cindex verify_ircapture
-@*Verify value captured during Capture-IR. Default is enabled.
-@item @b{var} <@var{name}> [@var{num_fields}|@var{del}] [@var{size1}] ...
-@cindex var
-@*Allocate, display or delete variable <@var{name}> [@var{num_fields}|@var{del}] [@var{size1}] ...
-@item @b{field} <@var{var}> <@var{field}> [@var{value}|@var{flip}]
-@cindex field
-Display/modify variable field <@var{var}> <@var{field}> [@var{value}|@var{flip}].
+@item A JTAG scan chain consists of a sequence of individual TAP
+devices such as a CPUs.
+@item Control operations involve moving each TAP through the same
+standard state machine (in parallel)
+using their shared TMS and clock signals.
+@item Data transfer involves shifting data through the chain of
+instruction or data registers of each TAP, writing new register values
+while the reading previous ones.
+@item Data register sizes are a function of the instruction active in
+a given TAP, while instruction register sizes are fixed for each TAP.
+All TAPs support a BYPASS instruction with a single bit data register.
+@item The way OpenOCD differentiates between TAP devices is by
+shifting different instructions into (and out of) their instruction
+registers.
@end itemize
-@section Tap states
-@cindex Tap states
-Available tap_states are:
+@section Low Level JTAG Commands
+
+These commands are used by developers who need to access
+JTAG instruction or data registers, possibly controlling
+the order of TAP state transitions.
+If you're not debugging OpenOCD internals, or bringing up a
+new JTAG adapter or a new type of TAP device (like a CPU or
+JTAG router), you probably won't need to use these commands.
+
+@deffn Command {drscan} tap [numbits value]+ [@option{-endstate} tap_state]
+Loads the data register of @var{tap} with a series of bit fields
+that specify the entire register.
+Each field is @var{numbits} bits long with
+a numeric @var{value} (hexadecimal encouraged).
+The return value holds the original value of each
+of those fields.
+
+For example, a 38 bit number might be specified as one
+field of 32 bits then one of 6 bits.
+@emph{For portability, never pass fields which are more
+than 32 bits long. Many OpenOCD implementations do not
+support 64-bit (or larger) integer values.}
+
+All TAPs other than @var{tap} must be in BYPASS mode.
+The single bit in their data registers does not matter.
+
+When @var{tap_state} is specified, the JTAG state machine is left
+in that state.
+For example @sc{drpause} might be specified, so that more
+instructions can be issued before re-entering the @sc{run/idle} state.
+If the end state is not specified, the @sc{run/idle} state is entered.
+
+@quotation Warning
+OpenOCD does not record information about data register lengths,
+so @emph{it is important that you get the bit field lengths right}.
+Remember that different JTAG instructions refer to different
+data registers, which may have different lengths.
+Moreover, those lengths may not be fixed;
+the SCAN_N instruction can change the length of
+the register accessed by the INTEST instruction
+(by connecting a different scan chain).
+@end quotation
+@end deffn
+
+@deffn Command {flush_count}
+Returns the number of times the JTAG queue has been flushed.
+This may be used for performance tuning.
+
+For example, flushing a queue over USB involves a
+minimum latency, often several milliseconds, which does
+not change with the amount of data which is written.
+You may be able to identify performance problems by finding
+tasks which waste bandwidth by flushing small transfers too often,
+instead of batching them into larger operations.
+@end deffn
+
+@deffn Command {irscan} [tap instruction]+ [@option{-endstate} tap_state]
+For each @var{tap} listed, loads the instruction register
+with its associated numeric @var{instruction}.
+(The number of bits in that instruction may be displayed
+using the @command{scan_chain} command.)
+For other TAPs, a BYPASS instruction is loaded.
+
+When @var{tap_state} is specified, the JTAG state machine is left
+in that state.
+For example @sc{irpause} might be specified, so the data register
+can be loaded before re-entering the @sc{run/idle} state.
+If the end state is not specified, the @sc{run/idle} state is entered.
+
+@quotation Note
+OpenOCD currently supports only a single field for instruction
+register values, unlike data register values.
+For TAPs where the instruction register length is more than 32 bits,
+portable scripts currently must issue only BYPASS instructions.
+@end quotation
+@end deffn
+
+@deffn Command {jtag_reset} trst srst
+Set values of reset signals.
+The @var{trst} and @var{srst} parameter values may be
+@option{0}, indicating that reset is inactive (pulled or driven high),
+or @option{1}, indicating it is active (pulled or driven low).
+The @command{reset_config} command should already have been used
+to configure how the board and JTAG adapter treat these two
+signals, and to say if either signal is even present.
+@xref{Reset Configuration}.
+@end deffn
+
+@deffn Command {runtest} @var{num_cycles}
+Move to the @sc{run/idle} state, and execute at least
+@var{num_cycles} of the JTAG clock (TCK).
+Instructions often need some time
+to execute before they take effect.
+@end deffn
+
+@deffn Command {scan_chain}
+Displays the TAPs in the scan chain configuration,
+and their status.
+The set of TAPs listed by this command is fixed by
+exiting the OpenOCD configuration stage,
+but systems with a JTAG router can
+enable or disable TAPs dynamically.
+In addition to the enable/disable status, the contents of
+each TAP's instruction register can also change.
+@end deffn
+
+@c tms_sequence (short|long)
+@c ... temporary, debug-only, probably gone before 0.2 ships
+
+@deffn Command {verify_ircapture} (@option{enable}|@option{disable})
+Verify values captured during @sc{ircapture} and returned
+during IR scans. Default is enabled, but this can be
+overridden by @command{verify_jtag}.
+@end deffn
+
+@deffn Command {verify_jtag} (@option{enable}|@option{disable})
+Enables verification of DR and IR scans, to help detect
+programming errors. For IR scans, @command{verify_ircapture}
+must also be enabled.
+Default is enabled.
+@end deffn
+
+@section TAP state names
+@cindex TAP state names
+
+The @var{tap_state} names used by OpenOCD in the @command{drscan},
+and @command{irscan} commands are:
+
@itemize @bullet
-@item @b{RESET}
-@cindex RESET
-@item @b{IDLE}
-@cindex IDLE
+@item @b{RESET} ... should act as if TRST were active
+@item @b{RUN/IDLE} ... don't assume this always means IDLE
@item @b{DRSELECT}
-@cindex DRSELECT
@item @b{DRCAPTURE}
-@cindex DRCAPTURE
-@item @b{DRSHIFT}
-@cindex DRSHIFT
+@item @b{DRSHIFT} ... TDI/TDO shifting through the data register
@item @b{DREXIT1}
-@cindex DREXIT1
-@item @b{DRPAUSE}
-@cindex DRPAUSE
+@item @b{DRPAUSE} ... data register ready for update or more shifting
@item @b{DREXIT2}
-@cindex DREXIT2
@item @b{DRUPDATE}
-@cindex DRUPDATE
@item @b{IRSELECT}
-@cindex IRSELECT
@item @b{IRCAPTURE}
-@cindex IRCAPTURE
-@item @b{IRSHIFT}
-@cindex IRSHIFT
+@item @b{IRSHIFT} ... TDI/TDO shifting through the instruction register
@item @b{IREXIT1}
-@cindex IREXIT1
-@item @b{IRPAUSE}
-@cindex IRPAUSE
+@item @b{IRPAUSE} ... instruction register ready for update or more shifting
@item @b{IREXIT2}
-@cindex IREXIT2
@item @b{IRUPDATE}
-@cindex IRUPDATE
@end itemize
+Note that only six of those states are fully ``stable'' in the
+face of TMS fixed (usually low)
+and a free-running JTAG clock. For all the
+others, the next TCK transition changes to a new state.
+
+@itemize @bullet
+@item From @sc{drshift} and @sc{irshift}, clock transitions will
+produce side effects by changing register contents. The values
+to be latched in upcoming @sc{drupdate} or @sc{irupdate} states
+may not be as expected.
+@item @sc{run/idle}, @sc{drpause}, and @sc{irpause} are reasonable
+choices after @command{drscan} or @command{irscan} commands,
+since they are free of JTAG side effects.
+However, @sc{run/idle} may have side effects that appear at other
+levels, such as advancing the ARM9E-S instruction pipeline.
+Consult the documentation for the TAP(s) you are working with.
+@end itemize
@node TFTP
@chapter TFTP
OpenOCD complies with the remote gdbserver protocol, and as such can be used
to debug remote targets.
+@anchor{Connecting to GDB}
@section Connecting to GDB
@cindex Connecting to GDB
-@anchor{Connecting to GDB}
Use GDB 6.7 or newer with OpenOCD if you run into trouble. For
instance GDB 6.3 has a known bug that produces bogus memory access
errors, which has since been fixed: look up 1836 in
@node Upgrading
@chapter Deprecated/Removed Commands
@cindex Deprecated/Removed Commands
-Certain OpenOCD commands have been deprecated/removed during the various revisions.
+Certain OpenOCD commands have been deprecated or
+removed during the various revisions.
+
+Upgrade your scripts as soon as possible.
+These descriptions for old commands may be removed
+a year after the command itself was removed.
+This means that in January 2010 this chapter may
+become much shorter.
@itemize @bullet
@item @b{arm7_9 fast_writes}
@cindex arm7_9 fast_writes
@*Use @command{arm7_9 fast_memory_access} instead.
+@item @b{endstate}
+@cindex endstate
+@*An buggy old command that would not really work since background polling would wipe out the global endstate
@xref{arm7_9 fast_memory_access}.
@item @b{arm7_9 force_hw_bkpts}
-@cindex arm7_9 force_hw_bkpts
@*Use @command{gdb_breakpoint_override} instead. Note that GDB will use hardware breakpoints
for flash if the GDB memory map has been set up(default when flash is declared in
target configuration). @xref{gdb_breakpoint_override}.
@item @b{arm7_9 sw_bkpts}
-@cindex arm7_9 sw_bkpts
@*On by default. @xref{gdb_breakpoint_override}.
@item @b{daemon_startup}
-@cindex daemon_startup
@*this config option has been removed, simply adding @option{init} and @option{reset halt} to
the end of your config script will give the same behaviour as using @option{daemon_startup reset}
and @option{target cortex_m3 little reset_halt 0}.
@item @b{dump_binary}
-@cindex dump_binary
@*use @option{dump_image} command with same args. @xref{dump_image}.
@item @b{flash erase}
-@cindex flash erase
@*use @option{flash erase_sector} command with same args. @xref{flash erase_sector}.
@item @b{flash write}
-@cindex flash write
@*use @option{flash write_bank} command with same args. @xref{flash write_bank}.
@item @b{flash write_binary}
-@cindex flash write_binary
@*use @option{flash write_bank} command with same args. @xref{flash write_bank}.
@item @b{flash auto_erase}
-@cindex flash auto_erase
@*use @option{flash write_image} command passing @option{erase} as the first parameter. @xref{flash write_image}.
+@item @b{jtag_device}
+@*use the @command{jtag newtap} command, converting from positional syntax
+to named prefixes, and naming the TAP.
+@xref{jtag newtap}.
+Note that if you try to use the old command, a message will tell you the
+right new command to use; and that the fourth parameter in the old syntax
+was never actually used.
+@example
+OLD: jtag_device 8 0x01 0xe3 0xfe
+NEW: jtag newtap CHIPNAME TAPNAME \
+ -irlen 8 -ircapture 0x01 -irmask 0xe3
+@end example
+
@item @b{jtag_speed} value
@*@xref{JTAG Speed}.
Usually, a value of zero means maximum
@end itemize
@item @b{load_binary}
-@cindex load_binary
@*use @option{load_image} command with same args. @xref{load_image}.
@item @b{run_and_halt_time}
-@cindex run_and_halt_time
@*This command has been removed for simpler reset behaviour, it can be simulated with the
following commands:
@smallexample
halt
@end smallexample
@item @b{target} <@var{type}> <@var{endian}> <@var{jtag-position}>
-@cindex target
@*use the create subcommand of @option{target}.
@item @b{target_script} <@var{target#}> <@var{eventname}> <@var{scriptname}>
-@cindex target_script
@*use <@var{target_name}> configure -event <@var{eventname}> "script <@var{scriptname}>"
@item @b{working_area}
-@cindex working_area
@*use the @option{configure} subcommand of @option{target} to set the work-area-virt, work-area-phy, work-area-size, and work-area-backup properties of the target.
@end itemize
@chapter FAQ
@cindex faq
@enumerate
-@item @b{RTCK, also known as: Adaptive Clocking - What is it?}
@anchor{FAQ RTCK}
+@item @b{RTCK, also known as: Adaptive Clocking - What is it?}
@cindex RTCK
@cindex adaptive clocking
@*
GDB issues software breakpoints when a normal breakpoint is requested, or to implement
source-line single-stepping. On ARMv4T systems, like ARM7TDMI, ARM720T or ARM920T,
-software breakpoints consume one of the two available hardware breakpoints.
+software breakpoints consume one of the two available hardware breakpoints.
@item @b{LPC2000 Flash} When erasing or writing LPC2000 on-chip flash, the operation fails at random.
else that needs to write to controller registers, perhaps for setting
up DRAM and loading it with code.
-@item @b{JTAG Tap Order} JTAG tap order - command order
+@anchor{FAQ TAP Order}
+@item @b{JTAG TAP Order} Do I have to declare the TAPS in some
+particular order?
-Many newer devices have multiple JTAG taps. For example: ST
-Microsystems STM32 chips have two taps, a ``boundary scan tap'' and
-``Cortex-M3'' tap. Example: The STM32 reference manual, Document ID:
+Yes; whenever you have more than one, you must declare them in
+the same order used by the hardware.
+
+Many newer devices have multiple JTAG TAPs. For example: ST
+Microsystems STM32 chips have two TAPs, a ``boundary scan TAP'' and
+``Cortex-M3'' TAP. Example: The STM32 reference manual, Document ID:
RM0008, Section 26.5, Figure 259, page 651/681, the ``TDI'' pin is
-connected to the boundary scan tap, which then connects to the
-Cortex-M3 tap, which then connects to the TDO pin.
+connected to the boundary scan TAP, which then connects to the
+Cortex-M3 TAP, which then connects to the TDO pin.
Thus, the proper order for the STM32 chip is: (1) The Cortex-M3, then
-(2) The boundary scan tap. If your board includes an additional JTAG
+(2) The boundary scan TAP. If your board includes an additional JTAG
chip in the scan chain (for example a Xilinx CPLD or FPGA) you could
place it before or after the STM32 chip in the chain. For example:
arm7_9_execute_sys_speed(): timeout waiting for SYSCOMP
TODO.
-
+
@end enumerate
@node Tcl Crash Course
SetResult( interp, "WRONG number of parameters");
return ERROR;
@}
-
+
// argv[0] = the ascii string just like C
// Execute the start statement.
SetResult( interp, "" );
return SUCCESS;
@}
-@end example
+@end example
Every other command IF, WHILE, FORMAT, PUTS, EXPR, everything works
in the same basic way.
@* SOURCE reads a file and executes as a script.
@end enumerate
@subsection format command
-@b{Where:} Generally occurs in numerous places.
+@b{Where:} Generally occurs in numerous places.
@* Tcl has no command like @b{printf()}, instead it has @b{format}, which is really more like
@b{sprintf()}.
@b{Example}
Code Review / openocd.git / blobdiff