This command is only available if your libusb1 is at least version 1.0.16.
@end deffn
+@deffn {Config Command} {adapter serial} serial_string
+Specifies the @var{serial_string} of the adapter to use.
+If this command is not specified, serial strings are not checked.
+Only the following adapter drivers use the serial string from this command:
+aice (aice_usb), arm-jtag-ew, cmsis_dap, ft232r, ftdi, hla (stlink, ti-icdi), jlink, kitprog, opendus,
+openjtag, osbdm, presto, rlink, st-link, usb_blaster (ublast2), usbprog, vsllink, xds110.
+@end deffn
+
@section Interface Drivers
Each of the interface drivers listed here must be explicitly
@end example
@end deffn
-@deffn {Config Command} {cmsis_dap_serial} [serial]
-Specifies the @var{serial} of the CMSIS-DAP device to use.
-If not specified, serial numbers are not considered.
-@end deffn
-
@deffn {Config Command} {cmsis_dap_backend} [@option{auto}|@option{usb_bulk}|@option{hid}]
Specifies how to communicate with the adapter:
during device selection.
@end deffn
-@deffn {Config Command} {ftdi serial} serial-number
-Specifies the @var{serial-number} of the adapter to use,
-in case the vendor provides unique IDs and more than one adapter
-is connected to the host.
-If not specified, serial numbers are not considered.
-(Note that USB serial numbers can be arbitrary Unicode strings,
-and are not restricted to containing only decimal digits.)
-@end deffn
-
@deffn {Config Command} {ftdi channel} channel
Selects the channel of the FTDI device to use for MPSSE operations. Most
adapters use the default, channel 0, but there are exceptions.
0x0403:0x6001 is used.
@end deffn
-@deffn {Config Command} {ft232r serial_desc} @var{serial}
-Specifies the @var{serial} of the adapter to use, in case the
-vendor provides unique IDs and more than one adapter is connected to
-the host. If not specified, serial numbers are not considered.
-@end deffn
-
@deffn {Config Command} {ft232r jtag_nums} @var{tck} @var{tms} @var{tdi} @var{tdo}
Set four JTAG GPIO numbers at once.
If not specified, default 0 3 1 2 or TXD CTS RXD RTS is used.
selection via USB address is not always unambiguous. It is recommended to use
the serial number instead, if possible.
-As a configuration command, it can be used only before 'init'.
-@end deffn
-@deffn {Config Command} {jlink serial} <serial number>
-Set the serial number of the interface, in case more than one adapter is
-connected to the host. If not specified, serial numbers are not considered.
-
As a configuration command, it can be used only before 'init'.
@end deffn
@end deffn
Please be aware that the acquisition sequence hard-resets the target.
@end deffn
-@deffn {Config Command} {kitprog_serial} serial
-Select a KitProg device by its @var{serial}. If left unspecified, the first
-device detected by OpenOCD will be used.
-@end deffn
-
@deffn {Command} {kitprog acquire_psoc}
Run a PSoC acquisition sequence immediately. Typically, this should not be used
outside of the target-specific configuration scripts since it hard-resets the
@deffn {Interface Driver} {presto}
ASIX PRESTO USB JTAG programmer.
-@deffn {Config Command} {presto serial} serial_string
-Configures the USB serial number of the Presto device to use.
-@end deffn
@end deffn
@deffn {Interface Driver} {rlink}
Currently Not Supported.
@end deffn
-@deffn {Config Command} {hla_serial} serial
-Specifies the serial number of the adapter.
-@end deffn
-
@deffn {Config Command} {hla_layout} (@option{stlink}|@option{icdi}|@option{nulink})
Specifies the adapter layout to use.
@end deffn
@emph{Note:} ST-Link TCP server does not support the SWIM transport.
@end deffn
-@deffn {Config Command} {st-link serial} serial
-Specifies the serial number of the adapter.
-@end deffn
-
@deffn {Config Command} {st-link vid_pid} [vid pid]+
Pairs of vendor IDs and product IDs of the device.
@end deffn
debug probe with the added capability to supply power to the target board. The
following commands are supported by the XDS110 driver:
-@deffn {Config Command} {xds110 serial} serial_string
-Specifies the serial number of which XDS110 probe to use. Otherwise, the first
-XDS110 found will be used.
-@end deffn
-
@deffn {Config Command} {xds110 supply} voltage_in_millivolts
Available only on the XDS110 stand-alone probe. Sets the voltage level of the
XDS110 power supply. A value of 0 leaves the supply off. Otherwise, the supply