@item @var{ir} ... is loaded into the JTAG IR to map the flash as the JTAG DR.
For the bitstreams generated from @file{xilinx_bscan_spi.py} this is the
@var{USER1} instruction.
-@item @var{dr_length} ... is the length of the DR register. This will be 1 for
-@file{xilinx_bscan_spi.py} bitstreams and most other cases.
@end itemize
@example
target create $_TARGETNAME testee -chain-position $_CHIPNAME.fpga
set _XILINX_USER1 0x02
-set _DR_LENGTH 1
flash bank $_FLASHNAME spi 0x0 0 0 0 \
- $_TARGETNAME $_XILINX_USER1 $_DR_LENGTH
+ $_TARGETNAME $_XILINX_USER1
@end example
@end deffn
+@deffn {Flash Driver} xcf
+@cindex Xilinx Platform flash driver
+@cindex xcf
+Xilinx FPGAs can be configured from specialized flash ICs named Platform Flash.
+It is (almost) regular NOR flash with erase sectors, program pages, etc. The
+only difference is special registers controlling its FPGA specific behavior.
+They must be properly configured for successful FPGA loading using
+additional @var{xcf} driver command:
+
+@deffn Command {xcf ccb} <bank_id>
+command accepts additional parameters:
+@itemize
+@item @var{external|internal} ... selects clock source.
+@item @var{serial|parallel} ... selects serial or parallel data bus mode.
+@item @var{slave|master} ... selects slave of master mode for flash device.
+@item @var{40|20} ... selects clock frequency in MHz for internal clock
+in master mode.
+@end itemize
+@example
+xcf ccb 0 external parallel slave 40
+@end example
+All of them must be specified even if clock frequency is pointless
+in slave mode. If only bank id specified than command prints current
+CCB register value. Note: there is no need to write this register
+every time you erase/program data sectors because it stores in
+dedicated sector.
+@end deffn
+
+@deffn Command {xcf configure} <bank_id>
+Initiates FPGA loading procedure. Useful if your board has no "configure"
+button.
+@example
+xcf configure 0
+@end example
+@end deffn
+
+Additional driver notes:
+@itemize
+@item Only single revision supported.
+@item Driver automatically detects need of bit reverse, but
+only "bin" (raw binary, do not confuse it with "bit") and "mcs"
+(Intel hex) file types supported.
+@item For additional info check xapp972.pdf and ug380.pdf.
+@end itemize
+@end deffn
+
@deffn {Flash Driver} lpcspifi
@cindex NXP SPI Flash Interface
@cindex SPIFI
In a debug session using JTAG for its transport protocol,
OpenOCD supports running such test files.
-@deffn Command {svf} filename [@option{quiet}]
+@deffn Command {svf} @file{filename} [@option{-tap @var{tapname}}] [@option{[-]quiet}] @
+ [@option{[-]nil}] [@option{[-]progress}] [@option{[-]ignore_error}]
This issues a JTAG reset (Test-Logic-Reset) and then
runs the SVF script from @file{filename}.
-Unless the @option{quiet} option is specified,
-each command is logged before it is executed.
+
+Arguments can be specified in any order; the optional dash doesn't
+affect their semantics.
+
+Command options:
+@itemize @minus
+@item @option{-tap @var{tapname}} ignore IR and DR headers and footers
+specified by the SVF file with HIR, TIR, HDR and TDR commands;
+instead, calculate them automatically according to the current JTAG
+chain configuration, targetting @var{tapname};
+@item @option{[-]quiet} do not log every command before execution;
+@item @option{[-]nil} ``dry run'', i.e., do not perform any operations
+on the real interface;
+@item @option{[-]progress} enable progress indication;
+@item @option{[-]ignore_error} continue execution despite TDO check
+errors.
+@end itemize
@end deffn
@section XSVF: Xilinx Serial Vector Format