Engine) mode built into many FTDI chips, such as the FT2232, FT4232 and FT232H.
The driver is using libusb-1.0 in asynchronous mode to talk to the FTDI device,
-bypassing intermediate libraries like libftdi of D2XX.
+bypassing intermediate libraries like libftdi or D2XX.
-A major improvement of this driver is that support for new FTDI based adapters
-can be added competely through configuration files, without the need to patch
-and rebuild OpenOCD.
+Support for new FTDI based adapters can be added competely through
+configuration files, without the need to patch and rebuild OpenOCD.
The driver uses a signal abstraction to enable Tcl configuration files to
define outputs for one or several FTDI GPIO. These outputs can then be
will be used for their customary purpose. Inputs can be read using the
@command{ftdi_get_signal} command.
+To support SWD, a signal named SWD_EN must be defined. It is set to 1 when the
+SWD protocol is selected. When set, the adapter should route the SWDIO pin to
+the data input. An SWDIO_OE signal, if defined, will be set to 1 or 0 as
+required by the protocol, to tell the adapter to drive the data output onto
+the SWDIO pin or keep the SWDIO pin Hi-Z, respectively.
+
Depending on the type of buffer attached to the FTDI GPIO, the outputs have to
be controlled differently. In order to support tristateable signals such as
nSRST, both a data GPIO and an output-enable GPIO can be specified for each
before initializing the JTAG scan chain:
@deffn {Config Command} {ftdi_vid_pid} [vid pid]+
-The vendor ID and product ID of the adapter. If not specified, the FTDI
-default values are used.
-Currently, up to eight [@var{vid}, @var{pid}] pairs may be given, e.g.
+The vendor ID and product ID of the adapter. Up to eight
+[@var{vid}, @var{pid}] pairs may be given, e.g.
@example
ftdi_vid_pid 0x0403 0xcff8 0x15ba 0x0003
@end example
@deffn {Command} {jlink config write}
Write the current configuration to the internal persistent storage.
@end deffn
+@deffn {Command} {jlink emucom write <channel> <data>}
+Write data to an EMUCOM channel. The data needs to be encoded as hexadecimal
+pairs.
+
+The following example shows how to write the three bytes 0xaa, 0x0b and 0x23 to
+the EMUCOM channel 0x10:
+@example
+> jlink emucom write 0x10 aa0b23
+@end example
+@end deffn
+@deffn {Command} {jlink emucom read <channel> <length>}
+Read data from an EMUCOM channel. The read data is encoded as hexadecimal
+pairs.
+
+The following example shows how to read 4 bytes from the EMUCOM channel 0x0:
+@example
+> jlink emucom read 0x0 4
+77a90000
+@end example
+@end deffn
@deffn {Config} {jlink usb} <@option{0} to @option{3}>
Set the USB address of the interface, in case more than one adapter is connected
to the host. If not specified, USB addresses are not considered. Device
@end deffn
+@deffn {Interface Driver} {openjtag}
+OpenJTAG compatible USB adapter.
+This defines some driver-specific commands:
+
+@deffn {Config Command} {openjtag_variant} variant
+Specifies the variant of the OpenJTAG adapter (see @uref{http://www.openjtag.org/}).
+Currently valid @var{variant} values include:
+
+@itemize @minus
+@item @b{standard} Standard variant (default).
+@item @b{cy7c65215} Cypress CY7C65215 Dual Channel USB-Serial Bridge Controller
+(see @uref{http://www.cypress.com/?rID=82870}).
+@end itemize
+@end deffn
+
+@deffn {Config Command} {openjtag_device_desc} string
+The USB device description string of the adapter.
+This value is only used with the standard variant.
+@end deffn
+@end deffn
+
@section Transport Configuration
@cindex Transport
As noted earlier, depending on the version of OpenOCD you use,
@anchor{rtostype}
@item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
-@var{rtos_type} can be one of @option{auto}|@option{eCos}|@option{ThreadX}|
-@option{FreeRTOS}|@option{linux}|@option{ChibiOS}|@option{embKernel}|@option{mqx}|
-@option{uCOS-III}
+@var{rtos_type} can be one of @option{auto}, @option{eCos},
+@option{ThreadX}, @option{FreeRTOS}, @option{linux}, @option{ChibiOS},
+@option{embKernel}, @option{mqx}, @option{uCOS-III}
@xref{gdbrtossupport,,RTOS Support}.
@item @code{-defer-examine} -- skip target examination at initial JTAG chain
scan and after a reset. A manual call to arp_examine is required to
access the target for debugging.
+@item @code{-ap-num} @var{ap_number} -- set DAP access port for target,
+@var{ap_number} is the numeric index of the DAP AP the target is connected to.
+Use this option with systems where multiple, independent cores are connected
+to separate access ports of the same DAP.
@end itemize
@end deffn
@anchor{flashprotect}
@deffn Command {flash protect} num first last (@option{on}|@option{off})
-Enable (@option{on}) or disable (@option{off}) protection of flash sectors
-in flash bank @var{num}, starting at sector @var{first}
+Enable (@option{on}) or disable (@option{off}) protection of flash blocks
+in flash bank @var{num}, starting at protection block @var{first}
and continuing up to and including @var{last}.
-Providing a @var{last} sector of @option{last}
+Providing a @var{last} block of @option{last}
specifies "to the end of the flash bank".
The @var{num} parameter is a value shown by @command{flash banks}.
+The protection block is usually identical to a flash sector.
+Some devices may utilize a protection block distinct from flash sector.
+See @command{flash info} for a list of protection blocks.
@end deffn
@deffn Command {flash padded_value} num value
the virtual banks are actually performed on the physical banks.
@example
flash bank $_FLASHNAME pic32mx 0x1fc00000 0 0 0 $_TARGETNAME
-flash bank vbank0 virtual 0xbfc00000 0 0 0 $_TARGETNAME $_FLASHNAME
-flash bank vbank1 virtual 0x9fc00000 0 0 0 $_TARGETNAME $_FLASHNAME
+flash bank vbank0 virtual 0xbfc00000 0 0 0 \
+ $_TARGETNAME $_FLASHNAME
+flash bank vbank1 virtual 0x9fc00000 0 0 0 \
+ $_TARGETNAME $_FLASHNAME
@end example
@end deffn
a proxy bitstream is to connect TDI-MOSI, TDO-MISO, TCK-CLK and activate
the flash chip select when the JTAG state machine is in SHIFT-DR. Such
a bitstream for several Xilinx FPGAs can be found in
-@file{contrib/loaders/flash/fpga/xilinx_bscan_spi.py}. It requires migen
-(@url{http://github.com/m-labs/migen}) and a Xilinx toolchain to build.
+@file{contrib/loaders/flash/fpga/xilinx_bscan_spi.py}. It requires
+@uref{https://github.com/m-labs/migen, migen} and a Xilinx toolchain to build.
This flash bank driver requires a target on a JTAG tap and will access that
tap directly. Since no support from the target is needed, the target can be a
target create $_TARGETNAME testee -chain-position $_CHIPNAME.fpga
set _XILINX_USER1 0x02
set _DR_LENGTH 1
-flash bank $_FLASHNAME spi 0x0 0 0 0 $_TARGETNAME $_XILINX_USER1 $_DR_LENGTH
+flash bank $_FLASHNAME spi 0x0 0 0 0 \
+ $_TARGETNAME $_XILINX_USER1 $_DR_LENGTH
@end example
@end deffn
# Flash bank 0
flash bank $_FLASHNAME ambiqmicro 0 0x00040000 0 0 $_TARGETNAME
# Flash bank 1 - same size as bank0, starts after bank 0.
-flash bank $_FLASHNAME ambiqmicro 0x00040000 0x00040000 0 0 $_TARGETNAME
+flash bank $_FLASHNAME ambiqmicro 0x00040000 0x00040000 0 0 \
+ $_TARGETNAME
@end example
Flash is programmed using custom entry points into the bootloader.
characters) ignored.
@example
-flash bank $@{_FLASHNAME@}0 fm4 0x00000000 0 0 0 $_TARGETNAME S6E2CCAJ0A
-flash bank $@{_FLASHNAME@}1 fm4 0x00100000 0 0 0 $_TARGETNAME S6E2CCAJ0A
+flash bank $@{_FLASHNAME@}0 fm4 0x00000000 0 0 0 \
+ $_TARGETNAME S6E2CCAJ0A
+flash bank $@{_FLASHNAME@}1 fm4 0x00100000 0 0 0 \
+ $_TARGETNAME S6E2CCAJ0A
@end example
@emph{The current implementation is incomplete. Protection is not supported,
nor is Chip Erase (only Sector Erase is implemented).}
@anchor{gdbrtossupport}
OpenOCD includes RTOS support, this will however need enabling as it defaults to disabled.
-It can be enabled by passing @option{-rtos} arg to the target @xref{rtostype,,RTOS Type}.
+It can be enabled by passing @option{-rtos} arg to the target. @xref{rtostype,,RTOS Type}.
+
+@xref{Threads, Debugging Programs with Multiple Threads,
+Debugging Programs with Multiple Threads, gdb, GDB manual}, for details about relevant
+GDB commands.
@* An example setup is below:
Code Review / openocd.git / blobdiff