* CPU Configuration:: CPU Configuration
* Flash Commands:: Flash Commands
* Flash Programming:: Flash Programming
-* NAND Flash Commands:: NAND Flash Commands
* PLD/FPGA Commands:: PLD/FPGA Commands
* General Commands:: General Commands
* Architecture and Core Commands:: Architecture and Core Commands
The OpenOCD web site provides the latest public news from the community:
-@uref{http://openocd.sourceforge.net/}
+@uref{http://openocd.org/}
@section Latest User's Guide:
available. A version for more recent code may be available.
Its HTML form is published regularly at:
-@uref{http://openocd.sourceforge.net/doc/html/index.html}
+@uref{http://openocd.org/doc/html/index.html}
PDF form is likewise published at:
-@uref{http://openocd.sourceforge.net/doc/pdf/openocd.pdf}
+@uref{http://openocd.org/doc/pdf/openocd.pdf}
@section OpenOCD User's Forum
technical information about the software internals, development
processes, and similar documentation:
-@uref{http://openocd.sourceforge.net/doc/doxygen/html/index.html}
+@uref{http://openocd.org/doc/doxygen/html/index.html}
This document is a work-in-progress, but contributions would be welcome
to fill in the gaps. All of the source files are provided in-tree,
The OpenOCD Bug Tracker is hosted on SourceForge:
-@uref{https://sourceforge.net/p/openocd/tickets/}
+@uref{http://bugs.openocd.org/}
@node Debug Adapter Hardware
@itemize @bullet
@item @b{Raisonance RLink}
-@* Link: @url{http://www.mcu-raisonance.com/~rlink-debugger-programmer__microcontrollers__tool~tool__T018:4cn9ziz4bnx6.html}
+@* Link: @url{http://www.mcu-raisonance.com/~rlink-debugger-programmer__@/microcontrollers__tool~tool__T018:4cn9ziz4bnx6.html}
@item @b{STM32 Primer}
@* Link: @url{http://www.stm32circle.com/resources/stm32primer.php}
@item @b{STM32 Primer2}
@example
Open On-Chip Debugger 0.4.0 (2010-01-14-15:06)
For bug reports, read
- http://openocd.sourceforge.net/doc/doxygen/bugs.html
+ http://openocd.org/doc/doxygen/bugs.html
Info : JTAG tap: lm3s.cpu tap/device found: 0x3ba00477
(mfg: 0x23b, part: 0xba00, ver: 0x3)
@end example
needs to get a new board working smoothly.
It provides guidelines for creating those files.
-You should find the following directories under @t{$(INSTALLDIR)/scripts},
-with files including the ones listed here.
-Use them as-is where you can; or as models for new files.
+You should find the following directories under
+@t{$(INSTALLDIR)/scripts}, with config files maintained upstream. Use
+them as-is where you can; or as models for new files.
@itemize @bullet
@item @file{interface} ...
-These are for debug adapters.
-Files that configure JTAG adapters go here.
-@example
-$ ls interface -R
-interface/:
-altera-usb-blaster.cfg hilscher_nxhx50_re.cfg openocd-usb-hs.cfg
-arm-jtag-ew.cfg hitex_str9-comstick.cfg openrd.cfg
-at91rm9200.cfg icebear.cfg osbdm.cfg
-axm0432.cfg jlink.cfg parport.cfg
-busblaster.cfg jtagkey2.cfg parport_dlc5.cfg
-buspirate.cfg jtagkey2p.cfg redbee-econotag.cfg
-calao-usb-a9260-c01.cfg jtagkey.cfg redbee-usb.cfg
-calao-usb-a9260-c02.cfg jtagkey-tiny.cfg rlink.cfg
-calao-usb-a9260.cfg jtag-lock-pick_tiny_2.cfg sheevaplug.cfg
-chameleon.cfg kt-link.cfg signalyzer.cfg
-cortino.cfg lisa-l.cfg signalyzer-h2.cfg
-digilent-hs1.cfg luminary.cfg signalyzer-h4.cfg
-dlp-usb1232h.cfg luminary-icdi.cfg signalyzer-lite.cfg
-dummy.cfg luminary-lm3s811.cfg stlink-v1.cfg
-estick.cfg minimodule.cfg stlink-v2.cfg
-flashlink.cfg neodb.cfg stm32-stick.cfg
-flossjtag.cfg ngxtech.cfg sysfsgpio-raspberrypi.cfg
-flossjtag-noeeprom.cfg olimex-arm-usb-ocd.cfg ti-icdi.cfg
-flyswatter2.cfg olimex-arm-usb-ocd-h.cfg turtelizer2.cfg
-flyswatter.cfg olimex-arm-usb-tiny-h.cfg ulink.cfg
-ftdi olimex-jtag-tiny.cfg usb-jtag.cfg
-hilscher_nxhx10_etm.cfg oocdlink.cfg usbprog.cfg
-hilscher_nxhx500_etm.cfg opendous.cfg vpaclink.cfg
-hilscher_nxhx500_re.cfg opendous_ftdi.cfg vsllink.cfg
-hilscher_nxhx50_etm.cfg openocd-usb.cfg xds100v2.cfg
-
-interface/ftdi:
-axm0432.cfg hitex_str9-comstick.cfg olimex-jtag-tiny.cfg
-calao-usb-a9260-c01.cfg icebear.cfg oocdlink.cfg
-calao-usb-a9260-c02.cfg jtagkey2.cfg opendous_ftdi.cfg
-cortino.cfg jtagkey2p.cfg openocd-usb.cfg
-dlp-usb1232h.cfg jtagkey.cfg openocd-usb-hs.cfg
-dp_busblaster.cfg jtag-lock-pick_tiny_2.cfg openrd.cfg
-flossjtag.cfg kt-link.cfg redbee-econotag.cfg
-flossjtag-noeeprom.cfg lisa-l.cfg redbee-usb.cfg
-flyswatter2.cfg luminary.cfg sheevaplug.cfg
-flyswatter.cfg luminary-icdi.cfg signalyzer.cfg
-gw16042.cfg luminary-lm3s811.cfg signalyzer-lite.cfg
-hilscher_nxhx10_etm.cfg minimodule.cfg stm32-stick.cfg
-hilscher_nxhx500_etm.cfg neodb.cfg turtelizer2-revB.cfg
-hilscher_nxhx500_re.cfg ngxtech.cfg turtelizer2-revC.cfg
-hilscher_nxhx50_etm.cfg olimex-arm-usb-ocd.cfg vpaclink.cfg
-hilscher_nxhx50_re.cfg olimex-arm-usb-ocd-h.cfg xds100v2.cfg
-hitex_lpc1768stick.cfg olimex-arm-usb-tiny-h.cfg
-$
-@end example
+These are for debug adapters. Files that specify configuration to use
+specific JTAG, SWD and other adapters go here.
@item @file{board} ...
-think Circuit Board, PWA, PCB, they go by many names. Board files
+Think Circuit Board, PWA, PCB, they go by many names. Board files
contain initialization items that are specific to a board.
+
They reuse target configuration files, since the same
microprocessor chips are used on many boards,
but support for external parts varies widely. For
sequence to enable that external flash or SDRAM should be found in the
board file. Boards may also contain multiple targets: two CPUs; or
a CPU and an FPGA.
-@example
-$ ls board
-actux3.cfg lpc1850_spifi_generic.cfg
-am3517evm.cfg lpc4350_spifi_generic.cfg
-arm_evaluator7t.cfg lubbock.cfg
-at91cap7a-stk-sdram.cfg mcb1700.cfg
-at91eb40a.cfg microchip_explorer16.cfg
-at91rm9200-dk.cfg mini2440.cfg
-at91rm9200-ek.cfg mini6410.cfg
-at91sam9261-ek.cfg netgear-dg834v3.cfg
-at91sam9263-ek.cfg olimex_LPC2378STK.cfg
-at91sam9g20-ek.cfg olimex_lpc_h2148.cfg
-atmel_at91sam7s-ek.cfg olimex_sam7_ex256.cfg
-atmel_at91sam9260-ek.cfg olimex_sam9_l9260.cfg
-atmel_at91sam9rl-ek.cfg olimex_stm32_h103.cfg
-atmel_sam3n_ek.cfg olimex_stm32_h107.cfg
-atmel_sam3s_ek.cfg olimex_stm32_p107.cfg
-atmel_sam3u_ek.cfg omap2420_h4.cfg
-atmel_sam3x_ek.cfg open-bldc.cfg
-atmel_sam4s_ek.cfg openrd.cfg
-balloon3-cpu.cfg osk5912.cfg
-colibri.cfg phone_se_j100i.cfg
-crossbow_tech_imote2.cfg phytec_lpc3250.cfg
-csb337.cfg pic-p32mx.cfg
-csb732.cfg propox_mmnet1001.cfg
-da850evm.cfg pxa255_sst.cfg
-digi_connectcore_wi-9c.cfg redbee.cfg
-diolan_lpc4350-db1.cfg rsc-w910.cfg
-dm355evm.cfg sheevaplug.cfg
-dm365evm.cfg smdk6410.cfg
-dm6446evm.cfg spear300evb.cfg
-efikamx.cfg spear300evb_mod.cfg
-eir.cfg spear310evb20.cfg
-ek-lm3s1968.cfg spear310evb20_mod.cfg
-ek-lm3s3748.cfg spear320cpu.cfg
-ek-lm3s6965.cfg spear320cpu_mod.cfg
-ek-lm3s811.cfg steval_pcc010.cfg
-ek-lm3s811-revb.cfg stm320518_eval_stlink.cfg
-ek-lm3s8962.cfg stm32100b_eval.cfg
-ek-lm3s9b9x.cfg stm3210b_eval.cfg
-ek-lm3s9d92.cfg stm3210c_eval.cfg
-ek-lm4f120xl.cfg stm3210e_eval.cfg
-ek-lm4f232.cfg stm3220g_eval.cfg
-embedded-artists_lpc2478-32.cfg stm3220g_eval_stlink.cfg
-ethernut3.cfg stm3241g_eval.cfg
-glyn_tonga2.cfg stm3241g_eval_stlink.cfg
-hammer.cfg stm32f0discovery.cfg
-hilscher_nxdb500sys.cfg stm32f3discovery.cfg
-hilscher_nxeb500hmi.cfg stm32f4discovery.cfg
-hilscher_nxhx10.cfg stm32ldiscovery.cfg
-hilscher_nxhx500.cfg stm32vldiscovery.cfg
-hilscher_nxhx50.cfg str910-eval.cfg
-hilscher_nxsb100.cfg telo.cfg
-hitex_lpc1768stick.cfg ti_am335xevm.cfg
-hitex_lpc2929.cfg ti_beagleboard.cfg
-hitex_stm32-performancestick.cfg ti_beagleboard_xm.cfg
-hitex_str9-comstick.cfg ti_beaglebone.cfg
-iar_lpc1768.cfg ti_blaze.cfg
-iar_str912_sk.cfg ti_pandaboard.cfg
-icnova_imx53_sodimm.cfg ti_pandaboard_es.cfg
-icnova_sam9g45_sodimm.cfg topas910.cfg
-imx27ads.cfg topasa900.cfg
-imx27lnst.cfg twr-k60f120m.cfg
-imx28evk.cfg twr-k60n512.cfg
-imx31pdk.cfg tx25_stk5.cfg
-imx35pdk.cfg tx27_stk5.cfg
-imx53loco.cfg unknown_at91sam9260.cfg
-keil_mcb1700.cfg uptech_2410.cfg
-keil_mcb2140.cfg verdex.cfg
-kwikstik.cfg voipac.cfg
-linksys_nslu2.cfg voltcraft_dso-3062c.cfg
-lisa-l.cfg x300t.cfg
-logicpd_imx27.cfg zy1000.cfg
-$
-@end example
@item @file{target} ...
-think chip. The ``target'' directory represents the JTAG TAPs
+Think chip. The ``target'' directory represents the JTAG TAPs
on a chip
which OpenOCD should control, not a board. Two common types of targets
are ARM chips and FPGA or CPLD chips.
When a chip has multiple TAPs (maybe it has both ARM and DSP cores),
the target config file defines all of them.
-@example
-$ ls target
-aduc702x.cfg lpc1764.cfg
-am335x.cfg lpc1765.cfg
-amdm37x.cfg lpc1766.cfg
-ar71xx.cfg lpc1767.cfg
-at32ap7000.cfg lpc1768.cfg
-at91r40008.cfg lpc1769.cfg
-at91rm9200.cfg lpc1788.cfg
-at91sam3ax_4x.cfg lpc17xx.cfg
-at91sam3ax_8x.cfg lpc1850.cfg
-at91sam3ax_xx.cfg lpc2103.cfg
-at91sam3nXX.cfg lpc2124.cfg
-at91sam3sXX.cfg lpc2129.cfg
-at91sam3u1c.cfg lpc2148.cfg
-at91sam3u1e.cfg lpc2294.cfg
-at91sam3u2c.cfg lpc2378.cfg
-at91sam3u2e.cfg lpc2460.cfg
-at91sam3u4c.cfg lpc2478.cfg
-at91sam3u4e.cfg lpc2900.cfg
-at91sam3uxx.cfg lpc2xxx.cfg
-at91sam3XXX.cfg lpc3131.cfg
-at91sam4sd32x.cfg lpc3250.cfg
-at91sam4sXX.cfg lpc4350.cfg
-at91sam4XXX.cfg lpc4350.cfg.orig
-at91sam7se512.cfg mc13224v.cfg
-at91sam7sx.cfg nuc910.cfg
-at91sam7x256.cfg omap2420.cfg
-at91sam7x512.cfg omap3530.cfg
-at91sam9260.cfg omap4430.cfg
-at91sam9260_ext_RAM_ext_flash.cfg omap4460.cfg
-at91sam9261.cfg omap5912.cfg
-at91sam9263.cfg omapl138.cfg
-at91sam9.cfg pic32mx.cfg
-at91sam9g10.cfg pxa255.cfg
-at91sam9g20.cfg pxa270.cfg
-at91sam9g45.cfg pxa3xx.cfg
-at91sam9rl.cfg readme.txt
-atmega128.cfg samsung_s3c2410.cfg
-avr32.cfg samsung_s3c2440.cfg
-c100.cfg samsung_s3c2450.cfg
-c100config.tcl samsung_s3c4510.cfg
-c100helper.tcl samsung_s3c6410.cfg
-c100regs.tcl sharp_lh79532.cfg
-cs351x.cfg sim3x.cfg
-davinci.cfg smp8634.cfg
-dragonite.cfg spear3xx.cfg
-dsp56321.cfg stellaris.cfg
-dsp568013.cfg stellaris_icdi.cfg
-dsp568037.cfg stm32f0x_stlink.cfg
-efm32_stlink.cfg stm32f1x.cfg
-epc9301.cfg stm32f1x_stlink.cfg
-faux.cfg stm32f2x.cfg
-feroceon.cfg stm32f2x_stlink.cfg
-fm3.cfg stm32f3x.cfg
-hilscher_netx10.cfg stm32f3x_stlink.cfg
-hilscher_netx500.cfg stm32f4x.cfg
-hilscher_netx50.cfg stm32f4x_stlink.cfg
-icepick.cfg stm32l.cfg
-imx21.cfg stm32lx_dual_bank.cfg
-imx25.cfg stm32lx_stlink.cfg
-imx27.cfg stm32_stlink.cfg
-imx28.cfg stm32w108_stlink.cfg
-imx31.cfg stm32xl.cfg
-imx35.cfg str710.cfg
-imx51.cfg str730.cfg
-imx53.cfg str750.cfg
-imx6.cfg str912.cfg
-imx.cfg swj-dp.tcl
-is5114.cfg test_reset_syntax_error.cfg
-ixp42x.cfg test_syntax_error.cfg
-k40.cfg ti-ar7.cfg
-k60.cfg ti_calypso.cfg
-lpc1751.cfg ti_dm355.cfg
-lpc1752.cfg ti_dm365.cfg
-lpc1754.cfg ti_dm6446.cfg
-lpc1756.cfg tmpa900.cfg
-lpc1758.cfg tmpa910.cfg
-lpc1759.cfg u8500.cfg
-lpc1763.cfg
-@end example
@item @emph{more} ... browse for other library files which may be useful.
For example, there are various generic and CPU-specific utilities.
@end itemize
@deffn {Config Command} gdb_target_description (@option{enable}|@option{disable})
Set to @option{enable} to cause OpenOCD to send the target descriptions to gdb via qXfer:features:read packet.
-The default behaviour is @option{disable}.
+The default behaviour is @option{enable}.
@end deffn
@deffn {Command} gdb_save_tdesc
@end example
@end deffn
-@deffn {Command} {usb_blaster} (@option{pin6}|@option{pin8}) (@option{0}|@option{1})
-Sets the state of the unused GPIO pins on USB-Blasters (pins 6 and 8 on the
-female JTAG header). These pins can be used as SRST and/or TRST provided the
-appropriate connections are made on the target board.
+@deffn {Command} {usb_blaster_pin} (@option{pin6}|@option{pin8}) (@option{0}|@option{1}|@option{s}|@option{t})
+Sets the state or function of the unused GPIO pins on USB-Blasters
+(pins 6 and 8 on the female JTAG header). These pins can be used as
+SRST and/or TRST provided the appropriate connections are made on the
+target board.
-For example, to use pin 6 as SRST (as with an AVR board):
+For example, to use pin 6 as SRST:
@example
-$_TARGETNAME configure -event reset-assert \
- "usb_blaster pin6 1; wait 1; usb_blaster pin6 0"
+usb_blaster_pin pin6 s
+reset_config srst_only
@end example
@end deffn
+@deffn {Command} {usb_blaster_lowlevel_driver} (@option{ftdi}|@option{ftd2xx}|@option{ublast2})
+Chooses the low level access method for the adapter. If not specified,
+@option{ftdi} is selected unless it wasn't enabled during the
+configure stage. USB-Blaster II needs @option{ublast2}.
+@end deffn
+
+@deffn {Command} {usb_blaster_firmware} @var{path}
+This command specifies @var{path} to access USB-Blaster II firmware
+image. To be used with USB-Blaster II only.
+@end deffn
+
@end deffn
@deffn {Interface Driver} {gw16012}
@end quotation
@end deffn
+@anchor{hla_interface}
@deffn {Interface Driver} {hla}
This is a driver that supports multiple High Level Adapters.
This type of adapter does not expose some of the lower level api's
Execute a custom adapter-specific command. The @var{command} string is
passed as is to the underlying adapter layout handler.
@end deffn
-
-@deffn {Config Command} {trace} source_clock_hz [output_file_path]
-Enable SWO tracing (if supported). The source clock rate for the
-trace port must be specified, this is typically the CPU clock rate. If
-the optional output file is specified then raw trace data is appended
-to the file, and the file is created if it does not exist.
-@end deffn
@end deffn
@deffn {Interface Driver} {opendous}
version of OpenOCD.
@end deffn
-@deffn Command {transport select} transport_name
+@deffn Command {transport select} @option{transport_name}
Select which of the supported transports to use in this OpenOCD session.
-The transport must be supported by the debug adapter hardware and by the
-version of OpenOCD you are using (including the adapter's driver).
-No arguments: returns name of session's selected transport.
+
+When invoked with @option{transport_name}, attempts to select the named
+transport. The transport must be supported by the debug adapter
+hardware and by the version of OpenOCD you are using (including the
+adapter's driver).
+
+If no transport has been selected and no @option{transport_name} is
+provided, @command{transport select} auto-selects the first transport
+supported by the debug adapter.
+
+@command{transport select} always returns the name of the session's selected
+transport, if any.
@end deffn
@subsection JTAG Transport
each of which must be explicitly declared.
JTAG supports both debugging and boundary scan testing.
Flash programming support is built on top of debug support.
+
+JTAG transport is selected with the command @command{transport select
+jtag}. Unless your adapter uses @ref{hla_interface,the hla interface
+driver}, in which case the command is @command{transport select
+hla_jtag}.
+
@subsection SWD Transport
@cindex SWD
@cindex Serial Wire Debug
SWD is debug-oriented, and does not support boundary scan testing.
Flash programming support is built on top of debug support.
(Some processors support both JTAG and SWD.)
+
+SWD transport is selected with the command @command{transport select
+swd}. Unless your adapter uses @ref{hla_interface,the hla interface
+driver}, in which case the command is @command{transport select
+hla_swd}.
+
@deffn Command {swd newdap} ...
Declares a single DAP which uses SWD transport.
Parameters are currently the same as "jtag newtap" but this is
No parameters: displays current settings.
@end deffn
-@subsection CMSIS-DAP Transport
-@cindex CMSIS-DAP
-CMSIS-DAP is an ARM-specific transport that is used to connect to
-compilant debuggers.
-
@subsection SPI Transport
@cindex SPI
@cindex Serial Peripheral Interface
@item @code{openrisc} -- this is an OpenRISC 1000 core.
The current implementation supports three JTAG TAP cores:
@itemize @minus
-@item @code{OpenCores TAP} (See: @emph{http://opencores.org/project,jtag})
-@item @code{Altera Virtual JTAG TAP} (See: @emph{http://www.altera.com/literature/ug/ug_virtualjtag.pdf})
-@item @code{Xilinx BSCAN_* virtual JTAG interface} (See: @emph{http://www.xilinx.com/support/documentation/sw_manuals/xilinx14_2/spartan6_hdl.pdf})
+@item @code{OpenCores TAP} (See: @url{http://opencores.org/project,jtag})
+@item @code{Altera Virtual JTAG TAP} (See: @url{http://www.altera.com/literature/ug/ug_virtualjtag.pdf})
+@item @code{Xilinx BSCAN_* virtual JTAG interface} (See: @url{http://www.xilinx.com/support/documentation/sw_manuals/xilinx14_2/spartan6_hdl.pdf})
@end itemize
And two debug interfaces cores:
@itemize @minus
-@item @code{Advanced debug interface} (See: @emph{http://opencores.org/project,adv_debug_sys})
-@item @code{SoC Debug Interface} (See: @emph{http://opencores.org/project,dbg_interface})
+@item @code{Advanced debug interface} (See: @url{http://opencores.org/project,adv_debug_sys})
+@item @code{SoC Debug Interface} (See: @url{http://opencores.org/project,dbg_interface})
@end itemize
@end itemize
@end deffn
@anchor{rtostype}
@item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
@var{rtos_type} can be one of @option{auto}|@option{eCos}|@option{ThreadX}|
-@option{FreeRTOS}|@option{linux}|@option{ChibiOS}|@option{embKernel}
+@option{FreeRTOS}|@option{linux}|@option{ChibiOS}|@option{embKernel}|@option{mqx}
@xref{gdbrtossupport,,RTOS Support}.
@end itemize
mychip.cpu configure -event gdb-attach my_attach_proc
mychip.cpu configure -event gdb-attach @{
echo "Reset..."
- # To make flash probe and gdb load to flash work we need a reset init.
+ # To make flash probe and gdb load to flash work
+ # we need a reset init.
reset init
@}
@end example
@* After all targets have resumed
@item @b{resumed}
@* Target has resumed
+@item @b{trace-config}
+@* After target hardware trace configuration was changed
@end itemize
@node Flash Commands
and allows driver-specific options and behaviors.
Some drivers also activate driver-specific commands.
+@deffn {Flash Driver} virtual
+This is a special driver that maps a previously defined bank to another
+address. All bank settings will be copied from the master physical bank.
+
+The @var{virtual} driver defines one mandatory parameters,
+
+@itemize
+@item @var{master_bank} The bank that this virtual address refers to.
+@end itemize
+
+So in the following example addresses 0xbfc00000 and 0x9fc00000 refer to
+the flash bank defined at address 0x1fc00000. Any cmds executed on
+the virtual banks are actually performed on the physical banks.
+@example
+flash bank $_FLASHNAME pic32mx 0x1fc00000 0 0 0 $_TARGETNAME
+flash bank vbank0 virtual 0xbfc00000 0 0 0 $_TARGETNAME $_FLASHNAME
+flash bank vbank1 virtual 0x9fc00000 0 0 0 $_TARGETNAME $_FLASHNAME
+@end example
+@end deffn
+
@subsection External Flash
@deffn {Flash Driver} cfi
@end deffn
+@deffn {Flash Driver} mrvlqspi
+This driver supports QSPI flash controller of Marvell's Wireless
+Microcontroller platform.
+
+The flash size is autodetected based on the table of known JEDEC IDs
+hardcoded in the OpenOCD sources.
+
+@example
+flash bank $_FLASHNAME mrvlqspi 0x0 0 0 0 $_TARGETNAME 0x46010000
+@end example
+
+@end deffn
+
@subsection Internal Flash (Microcontrollers)
@deffn {Flash Driver} aduc702x
This driver uses the same cmd names/syntax as @xref{at91sam3}.
@end deffn
+@deffn {Flash Driver} at91sam4l
+@cindex at91sam4l
+All members of the AT91SAM4L microcontroller family from
+Atmel include internal flash and use ARM's Cortex-M4 core.
+This driver uses the same cmd names/syntax as @xref{at91sam3}.
+
+The AT91SAM4L driver adds some additional commands:
+@deffn Command {at91sam4l smap_reset_deassert}
+This command releases internal reset held by SMAP
+and prepares reset vector catch in case of reset halt.
+Command is used internally in event event reset-deassert-post.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} at91sam7
All members of the AT91SAM7 microcontroller family from Atmel include
internal flash and use ARM7TDMI cores. The driver automatically
which is either @code{STR71x}, @code{STR73x} or @code{STR75x}.
@example
-flash bank $_FLASHNAME str7x 0x40000000 0x00040000 0 0 $_TARGETNAME STR71x
+flash bank $_FLASHNAME str7x \
+ 0x40000000 0x00040000 0 0 $_TARGETNAME STR71x
@end example
@deffn Command {str7x disable_jtag} bank
@end deffn
-@deffn {Flash Driver} tms470
-Most members of the TMS470 microcontroller family from Texas Instruments
-include internal flash and use ARM7TDMI cores.
-This driver doesn't require the chip and bus width to be specified.
-
-Some tms470-specific commands are defined:
-
-@deffn Command {tms470 flash_keyset} key0 key1 key2 key3
-Saves programming keys in a register, to enable flash erase and write commands.
-@end deffn
-
-@deffn Command {tms470 osc_mhz} clock_mhz
-Reports the clock speed, which is used to calculate timings.
-@end deffn
-
-@deffn Command {tms470 plldis} (0|1)
-Disables (@var{1}) or enables (@var{0}) use of the PLL to speed up
-the flash clock.
-@end deffn
-@end deffn
-
-@deffn {Flash Driver} virtual
-This is a special driver that maps a previously defined bank to another
-address. All bank settings will be copied from the master physical bank.
-
-The @var{virtual} driver defines one mandatory parameters,
-
-@itemize
-@item @var{master_bank} The bank that this virtual address refers to.
-@end itemize
-
-So in the following example addresses 0xbfc00000 and 0x9fc00000 refer to
-the flash bank defined at address 0x1fc00000. Any cmds executed on
-the virtual banks are actually performed on the physical banks.
-@example
-flash bank $_FLASHNAME pic32mx 0x1fc00000 0 0 0 $_TARGETNAME
-flash bank vbank0 virtual 0xbfc00000 0 0 0 $_TARGETNAME $_FLASHNAME
-flash bank vbank1 virtual 0x9fc00000 0 0 0 $_TARGETNAME $_FLASHNAME
-@end example
-@end deffn
-
-@deffn {Flash Driver} fm3
-All members of the FM3 microcontroller family from Fujitsu
-include internal flash and use ARM Cortex M3 cores.
-The @var{fm3} driver uses the @var{target} parameter to select the
-correct bank config, it can currently be one of the following:
-@code{mb9bfxx1.cpu}, @code{mb9bfxx2.cpu}, @code{mb9bfxx3.cpu},
-@code{mb9bfxx4.cpu}, @code{mb9bfxx5.cpu} or @code{mb9bfxx6.cpu}.
-
-@example
-flash bank $_FLASHNAME fm3 0 0 0 0 $_TARGETNAME
-@end example
-@end deffn
-
-@deffn {Flash Driver} sim3x
-All members of the SiM3 microcontroller family from Silicon Laboratories
-include internal flash and use ARM Cortex M3 cores. It supports both JTAG
-and SWD interface.
-The @var{sim3x} driver tries to probe the device to auto detect the MCU.
-If this failes, it will use the @var{size} parameter as the size of flash bank.
-
-@example
-flash bank $_FLASHNAME sim3x 0 $_CPUROMSIZE 0 0 $_TARGETNAME
-@end example
-
-There are 2 commands defined in the @var{sim3x} driver:
-
-@deffn Command {sim3x mass_erase}
-Erases the complete flash. This is used to unlock the flash.
-And this command is only possible when using the SWD interface.
-@end deffn
-
-@deffn Command {sim3x lock}
-Lock the flash. To unlock use the @command{sim3x mass_erase} command.
-@end deffn
-
-@end deffn
-
-@subsection str9xpec driver
+@deffn {Flash Driver} str9xpec
@cindex str9xpec
+Only use this driver for locking/unlocking the device or configuring the option bytes.
+Use the standard str9 driver for programming.
+Before using the flash commands the turbo mode must be enabled using the
+@command{str9xpec enable_turbo} command.
+
Here is some background info to help
you better understand how this driver works. OpenOCD has two flash drivers for
the str9:
has been locked. Halting the core is not required for the @option{str9xpec} driver
as mentioned above, just issue the commands above manually or from a telnet prompt.
-@deffn {Flash Driver} str9xpec
-Only use this driver for locking/unlocking the device or configuring the option bytes.
-Use the standard str9 driver for programming.
-Before using the flash commands the turbo mode must be enabled using the
-@command{str9xpec enable_turbo} command.
-
Several str9xpec-specific commands are defined:
@deffn Command {str9xpec disable_turbo} num
@end deffn
-@deffn {Flash Driver} nrf51
-All members of the nRF51 microcontroller families from Nordic Semiconductor
-include internal flash and use ARM Cortex-M0 core.
-
-@example
-flash bank $_FLASHNAME nrf51 0 0x00000000 0 0 $_TARGETNAME
-@end example
+@deffn {Flash Driver} tms470
+Most members of the TMS470 microcontroller family from Texas Instruments
+include internal flash and use ARM7TDMI cores.
+This driver doesn't require the chip and bus width to be specified.
-Some nrf51-specific commands are defined:
+Some tms470-specific commands are defined:
-@deffn Command {nrf51 mass_erase}
-Erases the contents of the code memory and user information
-configuration registers as well. It must be noted that this command
-works only for chips that do not have factory pre-programmed region 0
-code.
+@deffn Command {tms470 flash_keyset} key0 key1 key2 key3
+Saves programming keys in a register, to enable flash erase and write commands.
@end deffn
-@deffn {Flash Driver} mrvlqspi
-This driver supports QSPI flash controller of Marvell's Wireless
-Microcontroller platform.
+@deffn Command {tms470 osc_mhz} clock_mhz
+Reports the clock speed, which is used to calculate timings.
+@end deffn
-The flash size is autodetected based on the table of known JEDEC IDs
-hardcoded in the OpenOCD sources.
+@deffn Command {tms470 plldis} (0|1)
+Disables (@var{1}) or enables (@var{0}) use of the PLL to speed up
+the flash clock.
@end deffn
@end deffn
-@section mFlash
-
-@subsection mFlash Configuration
-@cindex mFlash Configuration
-
-@deffn {Config Command} {mflash bank} soc base RST_pin target
-Configures a mflash for @var{soc} host bank at
-address @var{base}.
-The pin number format depends on the host GPIO naming convention.
-Currently, the mflash driver supports s3c2440 and pxa270.
-
-Example for s3c2440 mflash where @var{RST pin} is GPIO B1:
+@deffn {Flash Driver} fm3
+All members of the FM3 microcontroller family from Fujitsu
+include internal flash and use ARM Cortex M3 cores.
+The @var{fm3} driver uses the @var{target} parameter to select the
+correct bank config, it can currently be one of the following:
+@code{mb9bfxx1.cpu}, @code{mb9bfxx2.cpu}, @code{mb9bfxx3.cpu},
+@code{mb9bfxx4.cpu}, @code{mb9bfxx5.cpu} or @code{mb9bfxx6.cpu}.
@example
-mflash bank $_FLASHNAME s3c2440 0x10000000 1b 0
+flash bank $_FLASHNAME fm3 0 0 0 0 $_TARGETNAME
@end example
+@end deffn
-Example for pxa270 mflash where @var{RST pin} is GPIO 43:
+@deffn {Flash Driver} sim3x
+All members of the SiM3 microcontroller family from Silicon Laboratories
+include internal flash and use ARM Cortex M3 cores. It supports both JTAG
+and SWD interface.
+The @var{sim3x} driver tries to probe the device to auto detect the MCU.
+If this failes, it will use the @var{size} parameter as the size of flash bank.
@example
-mflash bank $_FLASHNAME pxa270 0x08000000 43 0
+flash bank $_FLASHNAME sim3x 0 $_CPUROMSIZE 0 0 $_TARGETNAME
@end example
-@end deffn
-@subsection mFlash commands
-@cindex mFlash commands
+There are 2 commands defined in the @var{sim3x} driver:
-@deffn Command {mflash config pll} frequency
-Configure mflash PLL.
-The @var{frequency} is the mflash input frequency, in Hz.
-Issuing this command will erase mflash's whole internal nand and write new pll.
-After this command, mflash needs power-on-reset for normal operation.
-If pll was newly configured, storage and boot(optional) info also need to be update.
+@deffn Command {sim3x mass_erase}
+Erases the complete flash. This is used to unlock the flash.
+And this command is only possible when using the SWD interface.
@end deffn
-@deffn Command {mflash config boot}
-Configure bootable option.
-If bootable option is set, mflash offer the first 8 sectors
-(4kB) for boot.
+@deffn Command {sim3x lock}
+Lock the flash. To unlock use the @command{sim3x mass_erase} command.
@end deffn
-
-@deffn Command {mflash config storage}
-Configure storage information.
-For the normal storage operation, this information must be
-written.
@end deffn
-@deffn Command {mflash dump} num filename offset size
-Dump @var{size} bytes, starting at @var{offset} bytes from the
-beginning of the bank @var{num}, to the file named @var{filename}.
-@end deffn
+@deffn {Flash Driver} nrf51
+All members of the nRF51 microcontroller families from Nordic Semiconductor
+include internal flash and use ARM Cortex-M0 core.
-@deffn Command {mflash probe}
-Probe mflash.
-@end deffn
+@example
+flash bank $_FLASHNAME nrf51 0 0x00000000 0 0 $_TARGETNAME
+@end example
-@deffn Command {mflash write} num filename offset
-Write the binary file @var{filename} to mflash bank @var{num}, starting at
-@var{offset} bytes from the beginning of the bank.
-@end deffn
+Some nrf51-specific commands are defined:
-@node Flash Programming
-@chapter Flash Programming
+@deffn Command {nrf51 mass_erase}
+Erases the contents of the code memory and user information
+configuration registers as well. It must be noted that this command
+works only for chips that do not have factory pre-programmed region 0
+code.
+@end deffn
-OpenOCD implements numerous ways to program the target flash, whether internal or external.
-Programming can be acheived by either using GDB @ref{programmingusinggdb,,Programming using GDB},
-or using the cmds given in @ref{flashprogrammingcommands,,Flash Programming Commands}.
+@end deffn
-@*To simplify using the flash cmds directly a jimtcl script is available that handles the programming and verify stage.
-OpenOCD will program/verify/reset the target and optionally shutdown.
+@deffn {Flash Driver} mdr
+This drivers handles the integrated NOR flash on Milandr Cortex-M
+based controllers. A known limitation is that the Info memory can't be
+read or verified as it's not memory mapped.
-The script is executed as follows and by default the following actions will be peformed.
-@enumerate
-@item 'init' is executed.
-@item 'reset init' is called to reset and halt the target, any 'reset init' scripts are executed.
-@item @code{flash write_image} is called to erase and write any flash using the filename given.
-@item @code{verify_image} is called if @option{verify} parameter is given.
-@item @code{reset run} is called if @option{reset} parameter is given.
-@item OpenOCD is shutdown if @option{exit} parameter is given.
-@end enumerate
+@example
+flash bank <name> mdr <base> <size> \
+ 0 0 <target#> @var{type} @var{page_count} @var{sec_count}
+@end example
-An example of usage is given below. @xref{program}.
+@itemize @bullet
+@item @var{type} - 0 for main memory, 1 for info memory
+@item @var{page_count} - total number of pages
+@item @var{sec_count} - number of sector per page count
+@end itemize
+Example usage:
@example
-# program and verify using elf/hex/s19. verify and reset
-# are optional parameters
-openocd -f board/stm32f3discovery.cfg \
- -c "program filename.elf verify reset exit"
-
-# binary files need the flash address passing
-openocd -f board/stm32f3discovery.cfg \
- -c "program filename.bin exit 0x08000000"
+if @{ [info exists IMEMORY] && [string equal $IMEMORY true] @} @{
+ flash bank $@{_CHIPNAME@}_info.flash mdr 0x00000000 0x01000 \
+ 0 0 $_TARGETNAME 1 1 4
+@} else @{
+ flash bank $_CHIPNAME.flash mdr 0x00000000 0x20000 \
+ 0 0 $_TARGETNAME 0 32 4
+@}
@end example
+@end deffn
-@node NAND Flash Commands
-@chapter NAND Flash Commands
+@section NAND Flash Commands
@cindex NAND
Compared to NOR or SPI flash, NAND devices are inexpensive
modules with two smaller chips and individual chipselect lines.
@anchor{nandconfiguration}
-@section NAND Configuration Commands
+@subsection NAND Configuration Commands
@cindex NAND configuration
NAND chips must be declared in configuration scripts,
it with most other NAND commands.
@end deffn
-@section Erasing, Reading, Writing to NAND Flash
+@subsection Erasing, Reading, Writing to NAND Flash
@deffn Command {nand dump} num filename offset length [oob_option]
@cindex NAND reading
be removed in a future release.
@end deffn
-@section Other NAND commands
+@subsection Other NAND commands
@cindex NAND other commands
@deffn Command {nand check_bad_blocks} num [offset length]
@end deffn
@anchor{nanddriverlist}
-@section NAND Driver List
+@subsection NAND Driver List
As noted above, the @command{nand device} command allows
driver-specific options and behaviors.
Some controllers also activate controller-specific commands.
change any behavior.
@end deffn
+@section mFlash
+
+@subsection mFlash Configuration
+@cindex mFlash Configuration
+
+@deffn {Config Command} {mflash bank} soc base RST_pin target
+Configures a mflash for @var{soc} host bank at
+address @var{base}.
+The pin number format depends on the host GPIO naming convention.
+Currently, the mflash driver supports s3c2440 and pxa270.
+
+Example for s3c2440 mflash where @var{RST pin} is GPIO B1:
+
+@example
+mflash bank $_FLASHNAME s3c2440 0x10000000 1b 0
+@end example
+
+Example for pxa270 mflash where @var{RST pin} is GPIO 43:
+
+@example
+mflash bank $_FLASHNAME pxa270 0x08000000 43 0
+@end example
+@end deffn
+
+@subsection mFlash commands
+@cindex mFlash commands
+
+@deffn Command {mflash config pll} frequency
+Configure mflash PLL.
+The @var{frequency} is the mflash input frequency, in Hz.
+Issuing this command will erase mflash's whole internal nand and write new pll.
+After this command, mflash needs power-on-reset for normal operation.
+If pll was newly configured, storage and boot(optional) info also need to be update.
+@end deffn
+
+@deffn Command {mflash config boot}
+Configure bootable option.
+If bootable option is set, mflash offer the first 8 sectors
+(4kB) for boot.
+@end deffn
+
+@deffn Command {mflash config storage}
+Configure storage information.
+For the normal storage operation, this information must be
+written.
+@end deffn
+
+@deffn Command {mflash dump} num filename offset size
+Dump @var{size} bytes, starting at @var{offset} bytes from the
+beginning of the bank @var{num}, to the file named @var{filename}.
+@end deffn
+
+@deffn Command {mflash probe}
+Probe mflash.
+@end deffn
+
+@deffn Command {mflash write} num filename offset
+Write the binary file @var{filename} to mflash bank @var{num}, starting at
+@var{offset} bytes from the beginning of the bank.
+@end deffn
+
+@node Flash Programming
+@chapter Flash Programming
+
+OpenOCD implements numerous ways to program the target flash, whether internal or external.
+Programming can be acheived by either using GDB @ref{programmingusinggdb,,Programming using GDB},
+or using the cmds given in @ref{flashprogrammingcommands,,Flash Programming Commands}.
+
+@*To simplify using the flash cmds directly a jimtcl script is available that handles the programming and verify stage.
+OpenOCD will program/verify/reset the target and optionally shutdown.
+
+The script is executed as follows and by default the following actions will be peformed.
+@enumerate
+@item 'init' is executed.
+@item 'reset init' is called to reset and halt the target, any 'reset init' scripts are executed.
+@item @code{flash write_image} is called to erase and write any flash using the filename given.
+@item @code{verify_image} is called if @option{verify} parameter is given.
+@item @code{reset run} is called if @option{reset} parameter is given.
+@item OpenOCD is shutdown if @option{exit} parameter is given.
+@end enumerate
+
+An example of usage is given below. @xref{program}.
+
+@example
+# program and verify using elf/hex/s19. verify and reset
+# are optional parameters
+openocd -f board/stm32f3discovery.cfg \
+ -c "program filename.elf verify reset exit"
+
+# binary files need the flash address passing
+openocd -f board/stm32f3discovery.cfg \
+ -c "program filename.bin exit 0x08000000"
+@end example
+
@node PLD/FPGA Commands
@chapter PLD/FPGA Commands
@cindex PLD
(@command{script} command and @command{target_name} configuration).
@end deffn
-@deffn Command shutdown
-Close the OpenOCD daemon, disconnecting all clients (GDB, telnet, other).
+@deffn Command shutdown [@option{error}]
+Close the OpenOCD daemon, disconnecting all clients (GDB, telnet,
+other). If option @option{error} is used, OpenOCD will return a
+non-zero exit code to the parent process.
@end deffn
@anchor{debuglevel}
proc load_image_bin @{fname foffset address length @} @{
# Load data from fname filename at foffset offset to
# target at address. Load at most length bytes.
- load_image $fname [expr $address - $foffset] bin $address $length
+ load_image $fname [expr $address - $foffset] bin \
+ $address $length
@}
@end example
@end deffn
Defaulting to 0.
@end deffn
+@subsection ARMv7-M specific commands
+@cindex tracing
+@cindex SWO
+@cindex SWV
+@cindex TPIU
+@cindex ITM
+@cindex ETM
+
+@deffn Command {tpiu config} (@option{disable} | ((@option{external} | @option{internal @var{filename}}) @
+ (@option{sync @var{port_width}} | ((@option{manchester} | @option{uart}) @var{formatter_enable})) @
+ @var{TRACECLKIN_freq} [@var{trace_freq}]))
+
+ARMv7-M architecture provides several modules to generate debugging
+information internally (ITM, DWT and ETM). Their output is directed
+through TPIU to be captured externally either on an SWO pin (this
+configuration is called SWV) or on a synchronous parallel trace port.
+
+This command configures the TPIU module of the target and, if internal
+capture mode is selected, starts to capture trace output by using the
+debugger adapter features.
+
+Some targets require additional actions to be performed in the
+@b{trace-config} handler for trace port to be activated.
+
+Command options:
+@itemize @minus
+@item @option{disable} disable TPIU handling;
+@item @option{external} configure TPIU to let user capture trace
+output externally (with an additional UART or logic analyzer hardware);
+@item @option{internal @var{filename}} configure TPIU and debug adapter to
+gather trace data and append it to @var{filename} (which can be
+either a regular file or a named pipe);
+@item @option{sync @var{port_width}} use synchronous parallel trace output
+mode, and set port width to @var{port_width};
+@item @option{manchester} use asynchronous SWO mode with Manchester
+coding;
+@item @option{uart} use asynchronous SWO mode with NRZ (same as
+regular UART 8N1) coding;
+@item @var{formatter_enable} is @option{on} or @option{off} to enable
+or disable TPIU formatter which needs to be used when both ITM and ETM
+data is to be output via SWO;
+@item @var{TRACECLKIN_freq} this should be specified to match target's
+current TRACECLKIN frequency (usually the same as HCLK);
+@item @var{trace_freq} trace port frequency. Can be omitted in
+internal mode to let the adapter driver select the maximum supported
+rate automatically.
+@end itemize
+
+Example usage:
+@enumerate
+@item STM32L152 board is programmed with an application that configures
+PLL to provide core clock with 24MHz frequency; to use ITM output it's
+enough to:
+@example
+#include <libopencm3/cm3/itm.h>
+ ...
+ ITM_STIM8(0) = c;
+ ...
+@end example
+(the most obvious way is to use the first stimulus port for printf,
+for that this ITM_STIM8 assignment can be used inside _write(); to make it
+blocking to avoid data loss, add @code{while (!(ITM_STIM8(0) &
+ITM_STIM_FIFOREADY));});
+@item An FT2232H UART is connected to the SWO pin of the board;
+@item Commands to configure UART for 12MHz baud rate:
+@example
+$ setserial /dev/ttyUSB1 spd_cust divisor 5
+$ stty -F /dev/ttyUSB1 38400
+@end example
+(FT2232H's base frequency is 60MHz, spd_cust allows to alias 38400
+baud with our custom divisor to get 12MHz)
+@item @code{itmdump -f /dev/ttyUSB1 -d1}
+@item OpenOCD invocation line:
+@example
+openocd -f interface/stlink-v2-1.cfg \
+ -c "transport select hla_swd" \
+ -f target/stm32l1.cfg \
+ -c "tpiu config external uart off 24000000 12000000"
+@end example
+@end enumerate
+@end deffn
+
+@deffn Command {itm port} @var{port} (@option{0}|@option{1}|@option{on}|@option{off})
+Enable or disable trace output for ITM stimulus @var{port} (counting
+from 0). Port 0 is enabled on target creation automatically.
+@end deffn
+
+@deffn Command {itm ports} (@option{0}|@option{1}|@option{on}|@option{off})
+Enable or disable trace output for all ITM stimulus ports.
+@end deffn
+
@subsection Cortex-M specific commands
@cindex Cortex-M
@item @option{linux}
@item @option{ChibiOS}
@item @option{embKernel}
+@item @option{mqx}
@end itemize
@quotation Note
@item ThreadX symbols
_tx_thread_current_ptr, _tx_thread_created_ptr, _tx_thread_created_count.
@item FreeRTOS symbols
+@raggedright
pxCurrentTCB, pxReadyTasksLists, xDelayedTaskList1, xDelayedTaskList2,
pxDelayedTaskList, pxOverflowDelayedTaskList, xPendingReadyList,
-xTasksWaitingTermination, xSuspendedTaskList, uxCurrentNumberOfTasks, uxTopUsedPriority.
+uxCurrentNumberOfTasks, uxTopUsedPriority.
+@end raggedright
@item linux symbols
init_task.
@item ChibiOS symbols
@item embKernel symbols
Rtos::sCurrentTask, Rtos::sListReady, Rtos::sListSleep,
Rtos::sListSuspended, Rtos::sMaxPriorities, Rtos::sCurrentTaskCount.
+@item mqx symbols
+_mqx_kernel_data, MQX_init_struct.
@end table
For most RTOS supported the above symbols will be exported by default. However for
-some, eg. FreeRTOS @option{xTasksWaitingTermination} is only exported
-if @option{INCLUDE_vTaskDelete} is defined during the build.
+some, eg. FreeRTOS, extra steps must be taken.
+
+These RTOSes may require additional OpenOCD-specific file to be linked
+along with the project:
+
+@table @code
+@item FreeRTOS
+contrib/rtos-helpers/FreeRTOS-openocd.c
+@end table
@node Tcl Scripting API
@chapter Tcl Scripting API
Code Review / openocd.git / blobdiff