if you have a new kind of hardware interface
and need to provide a driver for it.
+@deffn {Command} {find} 'filename'
+Prints full path to @var{filename} according to OpenOCD search rules.
+@end deffn
+
+@deffn {Command} {ocd_find} 'filename'
+Prints full path to @var{filename} according to OpenOCD search rules. This
+is a low level function used by the @command{find}. Usually you want
+to use @command{find}, instead.
+@end deffn
+
@section Board Config Files
@cindex config file, board
@cindex board config file
After it leaves this stage, configuration commands may no
longer be issued.
+@deffn {Command} {command mode} [command_name]
+Returns the command modes allowed by a command: 'any', 'config', or
+'exec'. If no command is specified, returns the current command
+mode. Returns 'unknown' if an unknown command is given. Command can be
+multiple tokens. (command valid any time)
+
+In this document, the modes are described as stages, 'config' and
+'exec' mode correspond configuration stage and run stage. 'any' means
+the command can be executed in either
+stages. @xref{configurationstage,,Configuration Stage}, and
+@xref{enteringtherunstage,,Entering the Run Stage}.
+@end deffn
+
@anchor{enteringtherunstage}
@section Entering the Run Stage
OpenOCD executes the command for you after processing all
configuration files and/or command line options.
-@b{NOTE:} This command normally occurs at or near the end of your
+@b{NOTE:} This command normally occurs near the end of your
openocd.cfg file to force OpenOCD to ``initialize'' and make the
targets ready. For example: If your openocd.cfg file needs to
read/write memory on your target, @command{init} must occur before
the memory read/write commands. This includes @command{nand probe}.
+
+@command{init} calls the following internal OpenOCD commands to initialize
+corresponding subsystems:
+@deffn {Config Command} {target init}
+@deffnx {Command} {transport init}
+@deffnx {Command} {dap init}
+@deffnx {Config Command} {flash init}
+@deffnx {Config Command} {nand init}
+@deffnx {Config Command} {pld init}
+@deffnx {Command} {tpiu init}
+@end deffn
+@end deffn
+
+@deffn {Config Command} {noinit}
+Prevent OpenOCD from implicit @command{init} call at the end of startup.
+Allows issuing configuration commands over telnet or Tcl connection.
+When you are done with configuration use @command{init} to enter
+the run stage.
@end deffn
@deffn {Overridable Procedure} {jtag_init}
@subsection RISC-V Debug Configuration Commands
-@deffn {Command} {riscv expose_csrs} n0[-m0][,n1[-m1]]...
-Configure a list of inclusive ranges for CSRs to expose in addition to the
-standard ones. This must be executed before `init`.
+@deffn {Config Command} {riscv expose_csrs} n[-m|=name] [...]
+Configure which CSRs to expose in addition to the standard ones. The CSRs to expose
+can be specified as individual register numbers or register ranges (inclusive). For the
+individually listed CSRs, a human-readable name can optionally be set using the @code{n=name}
+syntax, which will get @code{csr_} prepended to it. If no name is provided, the register will be
+named @code{csr<n>}.
By default OpenOCD attempts to expose only CSRs that are mentioned in a spec,
and then only if the corresponding extension appears to be implemented. This
-command can be used if OpenOCD gets this wrong, or a target implements custom
+command can be used if OpenOCD gets this wrong, or if the target implements custom
CSRs.
+
+@example
+# Expose a single RISC-V CSR number 128 under the name "csr128":
+$_TARGETNAME expose_csrs 128
+
+# Expose multiple RISC-V CSRs 128..132 under names "csr128" through "csr132":
+$_TARGETNAME expose_csrs 128-132
+
+# Expose a single RISC-V CSR number 1996 under custom name "csr_myregister":
+$_TARGETNAME expose_csrs 1996=myregister
+@end example
@end deffn
-@deffn {Command} {riscv expose_custom} n0[-m0][,n1[-m1]]...
+@deffn {Config Command} {riscv expose_custom} n[-m|=name] [...]
The RISC-V Debug Specification allows targets to expose custom registers
through abstract commands. (See Section 3.5.1.1 in that document.) This command
-configures a list of inclusive ranges of those registers to expose. Number 0
-indicates the first custom register, whose abstract command number is 0xc000.
-This command must be executed before `init`.
+configures individual registers or register ranges (inclusive) that shall be exposed.
+Number 0 indicates the first custom register, whose abstract command number is 0xc000.
+For individually listed registers, a human-readable name can be optionally provided
+using the @code{n=name} syntax, which will get @code{custom_} prepended to it. If no
+name is provided, the register will be named @code{custom<n>}.
+
+@example
+# Expose one RISC-V custom register with number 0xc010 (0xc000 + 16)
+# under the name "custom16":
+$_TARGETNAME expose_custom 16
+
+# Expose a range of RISC-V custom registers with numbers 0xc010 .. 0xc018
+# (0xc000+16 .. 0xc000+24) under the names "custom16" through "custom24":
+$_TARGETNAME expose_custom 16-24
+
+# Expose one RISC-V custom register with number 0xc020 (0xc000 + 32) under
+# user-defined name "custom_myregister":
+$_TARGETNAME expose_custom 32=myregister
+@end example
@end deffn
@deffn {Command} {riscv set_command_timeout_sec} [seconds]
deasserted.
@end deffn
-@deffn {Command} {riscv set_prefer_sba} on|off
-When on, prefer to use System Bus Access to access memory. When off (default),
-prefer to use the Program Buffer to access memory.
+@deffn {Command} {riscv set_scratch_ram} none|[address]
+Set the address of 16 bytes of scratch RAM the debugger can use, or 'none'.
+This is used to access 64-bit floating point registers on 32-bit targets.
+@end deffn
+
+@deffn Command {riscv set_mem_access} method1 [method2] [method3]
+Specify which RISC-V memory access method(s) shall be used, and in which order
+of priority. At least one method must be specified.
+
+Available methods are:
+@itemize
+@item @code{progbuf} - Use RISC-V Debug Program Buffer to access memory.
+@item @code{sysbus} - Access memory via RISC-V Debug System Bus interface.
+@item @code{abstract} - Access memory via RISC-V Debug abstract commands.
+@end itemize
+
+By default, all memory access methods are enabled in the following order:
+@code{progbuf sysbus abstract}.
+
+This command can be used to change the memory access methods if the default
+behavior is not suitable for a particular target.
@end deffn
@deffn {Command} {riscv set_enable_virtual} on|off
Code Review / openocd.git / blobdiff