@deffn {Config Command} gdb_target_description (@option{enable}|@option{disable})
Set to @option{enable} to cause OpenOCD to send the target descriptions to gdb via qXfer:features:read packet.
-The default behaviour is @option{disable}.
+The default behaviour is @option{enable}.
@end deffn
@deffn {Command} gdb_save_tdesc
@end example
@end deffn
-@deffn {Command} {usb_blaster} (@option{pin6}|@option{pin8}) (@option{0}|@option{1})
-Sets the state of the unused GPIO pins on USB-Blasters (pins 6 and 8 on the
-female JTAG header). These pins can be used as SRST and/or TRST provided the
-appropriate connections are made on the target board.
+@deffn {Command} {usb_blaster_pin} (@option{pin6}|@option{pin8}) (@option{0}|@option{1}|@option{s}|@option{t})
+Sets the state or function of the unused GPIO pins on USB-Blasters
+(pins 6 and 8 on the female JTAG header). These pins can be used as
+SRST and/or TRST provided the appropriate connections are made on the
+target board.
-For example, to use pin 6 as SRST (as with an AVR board):
+For example, to use pin 6 as SRST:
@example
-$_TARGETNAME configure -event reset-assert \
- "usb_blaster pin6 1; wait 1; usb_blaster pin6 0"
+usb_blaster_pin pin6 s
+reset_config srst_only
@end example
@end deffn
+@deffn {Command} {usb_blaster_lowlevel_driver} (@option{ftdi}|@option{ftd2xx}|@option{ublast2})
+Chooses the low level access method for the adapter. If not specified,
+@option{ftdi} is selected unless it wasn't enabled during the
+configure stage. USB-Blaster II needs @option{ublast2}.
+@end deffn
+
+@deffn {Command} {usb_blaster_firmware} @var{path}
+This command specifies @var{path} to access USB-Blaster II firmware
+image. To be used with USB-Blaster II only.
+@end deffn
+
@end deffn
@deffn {Interface Driver} {gw16012}
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+@deffn Command {flash read_bank} num filename offset length
+Read @var{length} bytes from the flash bank @var{num} starting at @var{offset}
+and write the contents to the binary @file{filename}.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {flash verify_bank} num filename offset
+Compare the contents of the binary file @var{filename} with the contents of the
+flash @var{num} starting at @var{offset}. Fails if the contents do not match.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
@deffn Command {flash write_image} [erase] [unlock] filename [offset] [type]
Write the image @file{filename} to the current target's flash bank(s).
Only loadable sections from the image are written.
@c "cfi part_id" disabled
@end deffn
+@deffn {Flash Driver} jtagspi
+@cindex Generic JTAG2SPI driver
+@cindex SPI
+@cindex jtagspi
+@cindex bscan_spi
+Several FPGAs and CPLDs can retrieve their configuration (bitstream) from a
+SPI flash connected to them. To access this flash from the host, the device
+is first programmed with a special proxy bitstream that
+exposes the SPI flash on the device's JTAG interface. The flash can then be
+accessed through JTAG.
+
+Since signaling between JTAG and SPI is compatible, all that is required for
+a proxy bitstream is to connect TDI-MOSI, TDO-MISO, TCK-CLK and activate
+the flash chip select when the JTAG state machine is in SHIFT-DR. Such
+a bitstream for several Xilinx FPGAs can be found in
+@file{contrib/loaders/flash/fpga/xilinx_bscan_spi.py}. It requires migen
+(@url{http://github.com/m-labs/migen}) and a Xilinx toolchain to build.
+
+This flash bank driver requires a target on a JTAG tap and will access that
+tap directly. Since no support from the target is needed, the target can be a
+"testee" dummy. Since the target does not expose the flash memory
+mapping, target commands that would otherwise be expected to access the flash
+will not work. These include all @command{*_image} and
+@command{$target_name m*} commands as well as @command{program}. Equivalent
+functionality is available through the @command{flash write_bank},
+@command{flash read_bank}, and @command{flash verify_bank} commands.
+
+@itemize
+@item @var{ir} ... is loaded into the JTAG IR to map the flash as the JTAG DR.
+For the bitstreams generated from @file{xilinx_bscan_spi.py} this is the
+@var{USER1} instruction.
+@item @var{dr_length} ... is the length of the DR register. This will be 1 for
+@file{xilinx_bscan_spi.py} bitstreams and most other cases.
+@end itemize
+
+@example
+target create $_TARGETNAME testee -chain-position $_CHIPNAME.fpga
+set _XILINX_USER1 0x02
+set _DR_LENGTH 1
+flash bank $_FLASHNAME spi 0x0 0 0 0 $_TARGETNAME $_XILINX_USER1 $_DR_LENGTH
+@end example
+@end deffn
+
@deffn {Flash Driver} lpcspifi
@cindex NXP SPI Flash Interface
@cindex SPIFI
definition command, and may also define commands usable only with
that particular type of PLD.
-@deffn {FPGA Driver} virtex2
+@deffn {FPGA Driver} virtex2 [no_jstart]
Virtex-II is a family of FPGAs sold by Xilinx.
It supports the IEEE 1532 standard for In-System Configuration (ISC).
-No driver-specific PLD definition options are used,
-and one driver-specific command is defined.
+
+If @var{no_jstart} is non-zero, the JSTART instruction is not used after
+loading the bitstream. While required for Series2, Series3, and Series6, it
+breaks bitstream loading on Series7.
@deffn {Command} {virtex2 read_stat} num
Reads and displays the Virtex-II status register (STAT)
@item ThreadX symbols
_tx_thread_current_ptr, _tx_thread_created_ptr, _tx_thread_created_count.
@item FreeRTOS symbols
-@raggedright
+@c The following is taken from recent texinfo to provide compatibility
+@c with ancient versions that do not support @raggedright
+@tex
+\begingroup
+\rightskip0pt plus2em \spaceskip.3333em \xspaceskip.5em\relax
pxCurrentTCB, pxReadyTasksLists, xDelayedTaskList1, xDelayedTaskList2,
pxDelayedTaskList, pxOverflowDelayedTaskList, xPendingReadyList,
uxCurrentNumberOfTasks, uxTopUsedPriority.
-@end raggedright
+\par
+\endgroup
+@end tex
@item linux symbols
init_task.
@item ChibiOS symbols
Code Review / openocd.git / blobdiff