+@subsection ARMv8-A specific commands
+@cindex ARMv8-A
+@cindex aarch64
+
+@deffn Command {aarch64 cache_info}
+Display information about target caches
+@end deffn
+
+@deffn Command {aarch64 dbginit}
+This command enables debugging by clearing the OS Lock and sticky power-down and reset
+indications. It also establishes the expected, basic cross-trigger configuration the aarch64
+target code relies on. In a configuration file, the command would typically be called from a
+@code{reset-end} or @code{reset-deassert-post} handler, to re-enable debugging after a system reset.
+However, normally it is not necessary to use the command at all.
+@end deffn
+
+@deffn Command {aarch64 smp_on|smp_off}
+Enable and disable SMP handling. The state of SMP handling influences the way targets in an SMP group
+are handled by the run control. With SMP handling enabled, issuing halt or resume to one core will trigger
+halting or resuming of all cores in the group. The command @code{target smp} defines which targets are in the SMP
+group. With SMP handling disabled, all targets need to be treated individually.
+@end deffn
+
+@deffn Command {aarch64 maskisr} [@option{on}|@option{off}]
+Selects whether interrupts will be processed when single stepping. The default configuration is
+@option{on}.
+@end deffn
+
+@section Intel Architecture
+
+Intel Quark X10xx is the first product in the Quark family of SoCs. It is an IA-32
+(Pentium x86 ISA) compatible SoC. The core CPU in the X10xx is codenamed Lakemont.
+Lakemont version 1 (LMT1) is used in X10xx. The CPU TAP (Lakemont TAP) is used for
+software debug and the CLTAP is used for SoC level operations.
+Useful docs are here: https://communities.intel.com/community/makers/documentation
+@itemize
+@item Intel Quark SoC X1000 OpenOCD/GDB/Eclipse App Note (web search for doc num 330015)
+@item Intel Quark SoC X1000 Debug Operations User Guide (web search for doc num 329866)
+@item Intel Quark SoC X1000 Datasheet (web search for doc num 329676)
+@end itemize
+
+@subsection x86 32-bit specific commands
+The three main address spaces for x86 are memory, I/O and configuration space.
+These commands allow a user to read and write to the 64Kbyte I/O address space.
+
+@deffn Command {x86_32 idw} address
+Display the contents of a 32-bit I/O port from address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 idh} address
+Display the contents of a 16-bit I/O port from address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 idb} address
+Display the contents of a 8-bit I/O port from address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 iww} address
+Write the contents of a 32-bit I/O port to address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 iwh} address
+Write the contents of a 16-bit I/O port to address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 iwb} address
+Write the contents of a 8-bit I/O port to address range 0x0000 - 0xffff.
+@end deffn
+
+@section OpenRISC Architecture
+
+The OpenRISC CPU is a soft core. It is used in a programmable SoC which can be
+configured with any of the TAP / Debug Unit available.
+
+@subsection TAP and Debug Unit selection commands
+@deffn Command {tap_select} (@option{vjtag}|@option{mohor}|@option{xilinx_bscan})
+Select between the Altera Virtual JTAG , Xilinx Virtual JTAG and Mohor TAP.
+@end deffn
+@deffn Command {du_select} (@option{adv}|@option{mohor}) [option]
+Select between the Advanced Debug Interface and the classic one.
+
+An option can be passed as a second argument to the debug unit.
+
+When using the Advanced Debug Interface, option = 1 means the RTL core is
+configured with ADBG_USE_HISPEED = 1. This configuration skips status checking
+between bytes while doing read or write bursts.
+@end deffn
+
+@subsection Registers commands
+@deffn Command {addreg} [name] [address] [feature] [reg_group]
+Add a new register in the cpu register list. This register will be
+included in the generated target descriptor file.
+
+@strong{[feature]} must be "org.gnu.gdb.or1k.group[0..10]".
+
+@strong{[reg_group]} can be anything. The default register list defines "system",
+ "dmmu", "immu", "dcache", "icache", "mac", "debug", "perf", "power", "pic"
+ and "timer" groups.
+
+@emph{example:}
+@example
+addreg rtest 0x1234 org.gnu.gdb.or1k.group0 system
+@end example
+
+
+@end deffn
+@deffn Command {readgroup} (@option{group})
+Display all registers in @emph{group}.
+
+@emph{group} can be "system",
+ "dmmu", "immu", "dcache", "icache", "mac", "debug", "perf", "power", "pic",
+ "timer" or any new group created with addreg command.
+@end deffn
+
+@section RISC-V Architecture
+
+@uref{http://riscv.org/, RISC-V} is a free and open ISA. OpenOCD supports JTAG
+debug of targets that implement version 0.11 and 0.13 of the RISC-V Debug
+Specification.
+
+@subsection RISC-V Terminology
+
+A @emph{hart} is a hardware thread. A hart may share resources (eg. FPU) with
+another hart, or may be a separate core. RISC-V treats those the same, and
+OpenOCD exposes each hart as a separate core.
+
+@subsection RISC-V Debug Configuration Commands
+
+@deffn Command {riscv expose_csrs} n0[-m0][,n1[-m1]]...
+Configure a list of inclusive ranges for CSRs to expose in addition to the
+standard ones. This must be executed before `init`.
+
+By default OpenOCD attempts to expose only CSRs that are mentioned in a spec,
+and then only if the corresponding extension appears to be implemented. This
+command can be used if OpenOCD gets this wrong, or a target implements custom
+CSRs.
+@end deffn
+
+@deffn Command {riscv set_command_timeout_sec} [seconds]
+Set the wall-clock timeout (in seconds) for individual commands. The default
+should work fine for all but the slowest targets (eg. simulators).
+@end deffn
+
+@deffn Command {riscv set_reset_timeout_sec} [seconds]
+Set the maximum time to wait for a hart to come out of reset after reset is
+deasserted.
+@end deffn
+
+@deffn Command {riscv set_scratch_ram} none|[address]
+Set the address of 16 bytes of scratch RAM the debugger can use, or 'none'.
+This is used to access 64-bit floating point registers on 32-bit targets.
+@end deffn
+
+@deffn Command {riscv set_prefer_sba} on|off
+When on, prefer to use System Bus Access to access memory. When off, prefer to
+use the Program Buffer to access memory.
+@end deffn
+
+@subsection RISC-V Authentication Commands
+
+The following commands can be used to authenticate to a RISC-V system. Eg. a
+trivial challenge-response protocol could be implemented as follows in a
+configuration file, immediately following @command{init}:
+@example
+set challenge [ocd_riscv authdata_read]
+riscv authdata_write [expr $challenge + 1]
+@end example
+
+@deffn Command {riscv authdata_read}
+Return the 32-bit value read from authdata. Note that to get read value back in
+a TCL script, it needs to be invoked as @command{ocd_riscv authdata_read}.
+@end deffn
+
+@deffn Command {riscv authdata_write} value
+Write the 32-bit value to authdata.
+@end deffn
+
+@subsection RISC-V DMI Commands
+
+The following commands allow direct access to the Debug Module Interface, which
+can be used to interact with custom debug features.
+
+@deffn Command {riscv dmi_read}
+Perform a 32-bit DMI read at address, returning the value. Note that to get
+read value back in a TCL script, it needs to be invoked as @command{ocd_riscv
+dmi_read}.
+@end deffn
+
+@deffn Command {riscv dmi_write} address value
+Perform a 32-bit DMI write of value at address.
+@end deffn
+