The driver uses a signal abstraction to enable Tcl configuration files to
define outputs for one or several FTDI GPIO. These outputs can then be
-controlled using the @command{ftdi_set_signal} command. Special signal names
+controlled using the @command{ftdi set_signal} command. Special signal names
are reserved for nTRST, nSRST and LED (for blink) so that they, if defined,
will be used for their customary purpose. Inputs can be read using the
-@command{ftdi_get_signal} command.
+@command{ftdi get_signal} command.
To support SWD, a signal named SWD_EN must be defined. It is set to 1 when the
SWD protocol is selected. When set, the adapter should route the SWDIO pin to
These interfaces have several commands, used to configure the driver
before initializing the JTAG scan chain:
-@deffn {Config Command} {ftdi_vid_pid} [vid pid]+
+@deffn {Config Command} {ftdi vid_pid} [vid pid]+
The vendor ID and product ID of the adapter. Up to eight
[@var{vid}, @var{pid}] pairs may be given, e.g.
@example
-ftdi_vid_pid 0x0403 0xcff8 0x15ba 0x0003
+ftdi vid_pid 0x0403 0xcff8 0x15ba 0x0003
@end example
@end deffn
-@deffn {Config Command} {ftdi_device_desc} description
+@deffn {Config Command} {ftdi device_desc} description
Provides the USB device description (the @emph{iProduct string})
of the adapter. If not specified, the device description is ignored
during device selection.
@end deffn
-@deffn {Config Command} {ftdi_serial} serial-number
+@deffn {Config Command} {ftdi serial} serial-number
Specifies the @var{serial-number} of the adapter to use,
in case the vendor provides unique IDs and more than one adapter
is connected to the host.
and are not restricted to containing only decimal digits.)
@end deffn
-@deffn {Config Command} {ftdi_channel} channel
+@deffn {Config Command} {ftdi channel} channel
Selects the channel of the FTDI device to use for MPSSE operations. Most
adapters use the default, channel 0, but there are exceptions.
@end deffn
-@deffn {Config Command} {ftdi_layout_init} data direction
+@deffn {Config Command} {ftdi layout_init} data direction
Specifies the initial values of the FTDI GPIO data and direction registers.
Each value is a 16-bit number corresponding to the concatenation of the high
and low FTDI GPIO registers. The values should be selected based on the
and initially asserted reset signals.
@end deffn
-@deffn {Command} {ftdi_layout_signal} name [@option{-data}|@option{-ndata} data_mask] [@option{-input}|@option{-ninput} input_mask] [@option{-oe}|@option{-noe} oe_mask] [@option{-alias}|@option{-nalias} name]
+@deffn {Command} {ftdi layout_signal} name [@option{-data}|@option{-ndata} data_mask] [@option{-input}|@option{-ninput} input_mask] [@option{-oe}|@option{-noe} oe_mask] [@option{-alias}|@option{-nalias} name]
Creates a signal with the specified @var{name}, controlled by one or more FTDI
GPIO pins via a range of possible buffer connections. The masks are FTDI GPIO
register bitmasks to tell the driver the connection and type of the output
The @option{-oe} (or @option{-noe}) option tells where the output-enable (or
not-output-enable) input to the output buffer is connected. The options
@option{-input} and @option{-ninput} specify the bitmask for pins to be read
-with the method @command{ftdi_get_signal}.
+with the method @command{ftdi get_signal}.
Both @var{data_mask} and @var{oe_mask} need not be specified. For example, a
simple open-collector transistor driver would be specified with @option{-oe}
@var{name}.
@end deffn
-@deffn {Command} {ftdi_set_signal} name @option{0}|@option{1}|@option{z}
+@deffn {Command} {ftdi set_signal} name @option{0}|@option{1}|@option{z}
Set a previously defined signal to the specified level.
@itemize @minus
@item @option{0}, drive low
@end itemize
@end deffn
-@deffn {Command} {ftdi_get_signal} name
+@deffn {Command} {ftdi get_signal} name
Get the value of a previously defined signal.
@end deffn
-@deffn {Command} {ftdi_tdo_sample_edge} @option{rising}|@option{falling}
+@deffn {Command} {ftdi tdo_sample_edge} @option{rising}|@option{falling}
Configure TCK edge at which the adapter samples the value of the TDO signal
Due to signal propagation delays, sampling TDO on rising TCK can become quite
@deffn {Command} {$target_name array2mem} arrayname width address count
@deffnx {Command} {$target_name mem2array} arrayname width address count
These provide an efficient script-oriented interface to memory.
-The @code{array2mem} primitive writes bytes, halfwords, or words;
-while @code{mem2array} reads them.
+The @code{array2mem} primitive writes bytes, halfwords, words
+or double-words; while @code{mem2array} reads them.
In both cases, the TCL side uses an array, and
the target side uses raw memory.
@itemize
@item @var{arrayname} ... is the name of an array variable
-@item @var{width} ... is 8/16/32 - indicating the memory access size
+@item @var{width} ... is 8/16/32/64 - indicating the memory access size
@item @var{address} ... is the target memory address
@item @var{count} ... is the number of elements to process
@end itemize
@deffn {Command} {echo} [-n] message
Logs a message at "user" priority.
-Output @var{message} to stdout.
Option "-n" suppresses trailing newline.
@example
echo "Downloading kernel -- please wait"
Code Review / openocd.git / blobdiff