+@deffn Command {pic32mx unlock} bank
+Unlock and erase specified chip @var{bank}.
+This will remove any Code Protection.
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} psoc4
+All members of the PSoC 41xx/42xx microcontroller family from Cypress
+include internal flash and use ARM Cortex-M0 cores.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+Note: Erased internal flash reads as 00.
+System ROM of PSoC 4 does not implement erase of a flash sector.
+
+@example
+flash bank $_FLASHNAME psoc4 0 0 0 0 $_TARGETNAME
+@end example
+
+psoc4-specific commands
+@deffn Command {psoc4 flash_autoerase} num (on|off)
+Enables or disables autoerase mode for a flash bank.
+
+If flash_autoerase is off, use mass_erase before flash programming.
+Flash erase command fails if region to erase is not whole flash memory.
+
+If flash_autoerase is on, a sector is both erased and programmed in one
+system ROM call. Flash erase command is ignored.
+This mode is suitable for gdb load.
+
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {psoc4 mass_erase} num
+Erases the contents of the flash memory, protection and security lock.
+
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} psoc6
+Supports PSoC6 (CY8C6xxx) family of Cypress microcontrollers.
+PSoC6 is a dual-core device with CM0+ and CM4 cores. Both cores share
+the same Flash/RAM/MMIO address space.
+
+Flash in PSoC6 is split into three regions:
+@itemize @bullet
+@item Main Flash - this is the main storage for user application.
+Total size varies among devices, sector size: 256 kBytes, row size:
+512 bytes. Supports erase operation on individual rows.
+@item Work Flash - intended to be used as storage for user data
+(e.g. EEPROM emulation). Total size: 32 KBytes, sector size: 32 KBytes,
+row size: 512 bytes.
+@item Supervisory Flash - special region which contains device-specific
+service data. This region does not support erase operation. Only few rows can
+be programmed by the user, most of the rows are read only. Programming
+operation will erase row automatically.
+@end itemize
+
+All three flash regions are supported by the driver. Flash geometry is detected
+automatically by parsing data in SPCIF_GEOMETRY register.
+
+PSoC6 is equipped with NOR Flash so erased Flash reads as 0x00.
+
+@example
+flash bank main_flash_cm0 psoc6 0x10000000 0 0 0 $@{TARGET@}.cm0
+flash bank work_flash_cm0 psoc6 0x14000000 0 0 0 $@{TARGET@}.cm0
+flash bank super_flash_user_cm0 psoc6 0x16000800 0 0 0 $@{TARGET@}.cm0
+flash bank super_flash_nar_cm0 psoc6 0x16001A00 0 0 0 $@{TARGET@}.cm0
+flash bank super_flash_key_cm0 psoc6 0x16005A00 0 0 0 $@{TARGET@}.cm0
+flash bank super_flash_toc2_cm0 psoc6 0x16007C00 0 0 0 $@{TARGET@}.cm0
+
+flash bank main_flash_cm4 psoc6 0x10000000 0 0 0 $@{TARGET@}.cm4
+flash bank work_flash_cm4 psoc6 0x14000000 0 0 0 $@{TARGET@}.cm4
+flash bank super_flash_user_cm4 psoc6 0x16000800 0 0 0 $@{TARGET@}.cm4
+flash bank super_flash_nar_cm4 psoc6 0x16001A00 0 0 0 $@{TARGET@}.cm4
+flash bank super_flash_key_cm4 psoc6 0x16005A00 0 0 0 $@{TARGET@}.cm4
+flash bank super_flash_toc2_cm4 psoc6 0x16007C00 0 0 0 $@{TARGET@}.cm4
+@end example
+
+psoc6-specific commands
+@deffn Command {psoc6 reset_halt}
+Command can be used to simulate broken Vector Catch from gdbinit or tcl scripts.
+When invoked for CM0+ target, it will set break point at application entry point
+and issue SYSRESETREQ. This will reset both cores and all peripherals. CM0+ will
+reset CM4 during boot anyway so this is safe. On CM4 target, VECTRESET is used
+instead of SYSRESETREQ to avoid unwanted reset of CM0+;
+@end deffn
+
+@deffn Command {psoc6 mass_erase} num
+Erases the contents given flash bank. The @var{num} parameter is a value shown
+by @command{flash banks}.
+Note: only Main and Work flash regions support Erase operation.
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} sim3x
+All members of the SiM3 microcontroller family from Silicon Laboratories
+include internal flash and use ARM Cortex-M3 cores. It supports both JTAG
+and SWD interface.
+The @var{sim3x} driver tries to probe the device to auto detect the MCU.
+If this failes, it will use the @var{size} parameter as the size of flash bank.
+
+@example
+flash bank $_FLASHNAME sim3x 0 $_CPUROMSIZE 0 0 $_TARGETNAME
+@end example
+
+There are 2 commands defined in the @var{sim3x} driver:
+
+@deffn Command {sim3x mass_erase}
+Erases the complete flash. This is used to unlock the flash.
+And this command is only possible when using the SWD interface.
+@end deffn
+
+@deffn Command {sim3x lock}
+Lock the flash. To unlock use the @command{sim3x mass_erase} command.
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} stellaris
+All members of the Stellaris LM3Sxxx, LM4x and Tiva C microcontroller
+families from Texas Instruments include internal flash. The driver
+automatically recognizes a number of these chips using the chip
+identification register, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME stellaris 0 0 0 0 $_TARGETNAME
+@end example
+
+@deffn Command {stellaris recover}
+Performs the @emph{Recovering a "Locked" Device} procedure to restore
+the flash and its associated nonvolatile registers to their factory
+default values (erased). This is the only way to remove flash
+protection or re-enable debugging if that capability has been
+disabled.
+
+Note that the final "power cycle the chip" step in this procedure
+must be performed by hand, since OpenOCD can't do it.
+@quotation Warning
+if more than one Stellaris chip is connected, the procedure is
+applied to all of them.
+@end quotation
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} stm32f1x
+All members of the STM32F0, STM32F1 and STM32F3 microcontroller families
+from ST Microelectronics include internal flash and use ARM Cortex-M0/M3/M4 cores.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME stm32f1x 0 0 0 0 $_TARGETNAME
+@end example
+
+Note that some devices have been found that have a flash size register that contains
+an invalid value, to workaround this issue you can override the probed value used by
+the flash driver.
+
+@example
+flash bank $_FLASHNAME stm32f1x 0 0x20000 0 0 $_TARGETNAME
+@end example
+
+If you have a target with dual flash banks then define the second bank
+as per the following example.
+@example
+flash bank $_FLASHNAME stm32f1x 0x08080000 0 0 0 $_TARGETNAME
+@end example
+
+Some stm32f1x-specific commands are defined:
+
+@deffn Command {stm32f1x lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32f1x unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32f1x mass_erase} num
+Mass erases the entire stm32f1x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32f1x options_read} num
+Read and display the stm32 option bytes written by
+the @command{stm32f1x options_write} command.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32f1x options_write} num (@option{SWWDG}|@option{HWWDG}) (@option{RSTSTNDBY}|@option{NORSTSTNDBY}) (@option{RSTSTOP}|@option{NORSTSTOP})
+Writes the stm32 option byte with the specified values.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} stm32f2x
+All members of the STM32F2, STM32F4 and STM32F7 microcontroller families from ST Microelectronics
+include internal flash and use ARM Cortex-M3/M4/M7 cores.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
+@end example
+
+Note that some devices have been found that have a flash size register that contains
+an invalid value, to workaround this issue you can override the probed value used by
+the flash driver.
+
+@example
+flash bank $_FLASHNAME stm32f2x 0 0x20000 0 0 $_TARGETNAME
+@end example
+
+Some stm32f2x-specific commands are defined:
+
+@deffn Command {stm32f2x lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32f2x unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32f2x mass_erase} num
+Mass erases the entire stm32f2x device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32f2x options_read} num
+Reads and displays user options and (where implemented) boot_addr0, boot_addr1, optcr2.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32f2x options_write} num user_options boot_addr0 boot_addr1
+Writes user options and (where implemented) boot_addr0 and boot_addr1 in raw format.
+Warning: The meaning of the various bits depends on the device, always check datasheet!
+The @var{num} parameter is a value shown by @command{flash banks}, @var{user_options} a
+12 bit value, consisting of bits 31-28 and 7-0 of FLASH_OPTCR, @var{boot_addr0} and
+@var{boot_addr1} two halfwords (of FLASH_OPTCR1).
+@end deffn
+
+@deffn Command {stm32f2x optcr2_write} num optcr2
+Writes FLASH_OPTCR2 options. Warning: Clearing PCROPi bits requires a full mass erase!
+The @var{num} parameter is a value shown by @command{flash banks}, @var{optcr2} a 32-bit word.
+@end deffn
+@end deffn
+
+@deffn {Flash Driver} stm32h7x
+All members of the STM32H7 microcontroller families from ST Microelectronics
+include internal flash and use ARM Cortex-M7 core.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+@example
+flash bank $_FLASHNAME stm32h7x 0 0 0 0 $_TARGETNAME
+@end example
+
+Note that some devices have been found that have a flash size register that contains
+an invalid value, to workaround this issue you can override the probed value used by
+the flash driver.
+
+@example
+flash bank $_FLASHNAME stm32h7x 0 0x20000 0 0 $_TARGETNAME
+@end example
+
+Some stm32h7x-specific commands are defined:
+
+@deffn Command {stm32h7x lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32h7x unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32h7x mass_erase} num
+Mass erases the entire stm32h7x device.
+The @var{num} parameter is a value shown by @command{flash banks}.