jtag/drivers/libusb0_common: fix FTBFS (libusb_device_descriptor error)

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index 3977454bba8b7dae71b780cb222b3cf2df06e708..e51de4de9108a01607e48faa8b6f5211c212eb00 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -2767,7 +2767,7 @@ minimal impact on the target system. Avoid floating inputs, conflicting outputs
 and initially asserted reset signals.
 @end deffn
 
-@deffn {Config Command} {ftdi_layout_signal} name [@option{-data}|@option{-ndata} data_mask] [@option{-oe}|@option{-noe} oe_mask]
+@deffn {Config Command} {ftdi_layout_signal} name [@option{-data}|@option{-ndata} data_mask] [@option{-oe}|@option{-noe} oe_mask] [@option{-alias}|@option{-nalias} name]
 Creates a signal with the specified @var{name}, controlled by one or more FTDI
 GPIO pins via a range of possible buffer connections. The masks are FTDI GPIO
 register bitmasks to tell the driver the connection and type of the output
@@ -2790,6 +2790,10 @@ target without any buffer. The FTDI pin is then switched between output and
 input as necessary to provide the full set of low, high and Hi-Z
 characteristics. In all other cases, the pins specified in a signal definition
 are always driven by the FTDI.
+
+If @option{-alias} or @option{-nalias} is used, the signal is created
+identical (or with data inverted) to an already specified signal
+@var{name}.
 @end deffn
 
 @deffn {Command} {ftdi_set_signal} name @option{0}|@option{1}|@option{z}
@@ -5173,9 +5177,10 @@ supported.}
 @end deffn
 
 @deffn {Flash Driver} lpc2000
-Most members of the LPC1700, LPC1800, LPC2000 and LPC4300 microcontroller
-families from NXP include internal flash and use Cortex-M3 (LPC1700, LPC1800),
-Cortex-M4 (LPC4300) or ARM7TDMI (LPC2000) cores.
+All members of the LPC11(x)00 and LPC1300 microcontroller families and most members
+of the LPC1700, LPC1800, LPC2000 and LPC4300 microcontroller families from NXP
+include internal flash and use Cortex-M0 (LPC11(x)00), Cortex-M3 (LPC1300, LPC1700,
+LPC1800), Cortex-M4 (LPC4300) or ARM7TDMI (LPC2000) cores.
 
 @quotation Note
 There are LPC2000 devices which are not supported by the @var{lpc2000}
@@ -5192,8 +5197,11 @@ which must appear in the following order:
 @option{lpc2000_v1} (older LPC21xx and LPC22xx)
 @option{lpc2000_v2} (LPC213x, LPC214x, LPC210[123], LPC23xx and LPC24xx)
 @option{lpc1700} (LPC175x and LPC176x)
-or @option{lpc4300} - available also as @option{lpc1800} alias (LPC18x[2357] and
+@option{lpc4300} - available also as @option{lpc1800} alias (LPC18x[2357] and
 LPC43x[2357])
+@option{lpc1100} (LPC11(x)xx and LPC13xx)
+or @option{auto} - automatically detects flash variant and size for LPC11(x)00,
+LPC1300 and LPC1700
 @item @var{clock_kHz} ... the frequency, in kiloHertz,
 at which the core is running
 @item @option{calc_checksum} ... optional (but you probably want to provide this!),
@@ -6723,10 +6731,12 @@ using @var{mask} to mark ``don't care'' fields.
 @section Misc Commands
 
 @cindex profiling
-@deffn Command {profile} seconds filename
+@deffn Command {profile} seconds filename [start end]
 Profiling samples the CPU's program counter as quickly as possible,
 which is useful for non-intrusive stochastic profiling.
-Saves up to 10000 sampines in @file{filename} using ``gmon.out'' format.
+Saves up to 10000 samples in @file{filename} using ``gmon.out''
+format. Optional @option{start} and @option{end} parameters allow to
+limit the address range.
 @end deffn
 
 @deffn Command {version}