If you disable all access through TCP/IP, you will need to
use the command line @option{-pipe} option.
+@anchor{gdb_port}
@deffn {Command} gdb_port [number]
@cindex GDB server
Normally gdb listens to a TCP/IP port, but GDB can also
second target will listen on gdb_port + 1, and so on.
When not specified during the configuration stage,
the port @var{number} defaults to 3333.
+When @var{number} is not a numeric value, incrementing it to compute
+the next port number does not work. In this case, specify the proper
+@var{number} for each target by using the option @code{-gdb-port} of the
+commands @command{target create} or @command{$target_name configure}.
+@xref{gdbportoverride,,option -gdb-port}.
Note: when using "gdb_port pipe", increasing the default remote timeout in
gdb (with 'set remotetimeout') is recommended. An insufficient timeout may
cause initialization to fail with "Unknown remote qXfer reply: OK".
-
@end deffn
@deffn {Command} tcl_port [number]
Select AP @var{num}, defaulting to 0.
@end deffn
+@deffn Command {$dap_name dpreg} reg [value]
+Displays the content of DP register at address @var{reg}, or set it to a new
+value @var{value}.
+
+In case of SWD, @var{reg} is a value in packed format
+@math{dpbanksel << 4 | addr} and assumes values 0, 4, 8 ... 0xfc.
+In case of JTAG it only assumes values 0, 4, 8 and 0xc.
+
+@emph{Note:} Consider using @command{poll off} to avoid any disturbing
+background activity by OpenOCD while you are operating at such low-level.
+@end deffn
+
@deffn Command {$dap_name baseaddr} [num]
Displays debug base address from MEM-AP @var{num},
defaulting to the currently selected AP.
@item @code{dragonite} -- resembles arm966e
@item @code{dsp563xx} -- implements Freescale's 24-bit DSP.
(Support for this is still incomplete.)
+@item @code{esirisc} -- this is an EnSilica eSi-RISC core.
+The current implementation supports eSi-32xx cores.
@item @code{fa526} -- resembles arm920 (w/o Thumb)
@item @code{feroceon} -- resembles arm926
@item @code{mips_m4k} -- a MIPS core
@item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
@var{rtos_type} can be one of @option{auto}, @option{eCos},
@option{ThreadX}, @option{FreeRTOS}, @option{linux}, @option{ChibiOS},
-@option{embKernel}, @option{mqx}, @option{uCOS-III}
+@option{embKernel}, @option{mqx}, @option{uCOS-III}, @option{nuttx}
@xref{gdbrtossupport,,RTOS Support}.
@item @code{-defer-examine} -- skip target examination at initial JTAG chain
where it is a mandatory configuration for the target run control.
@xref{armcrosstrigger,,ARM Cross-Trigger Interface},
for instruction on how to declare and control a CTI instance.
+
+@anchor{gdbportoverride}
+@item @code{-gdb-port} @var{number} -- see command @command{gdb_port} for the
+possible values of the parameter @var{number}, which are not only numeric values.
+Use this option to override, for this target only, the global parameter set with
+command @command{gdb_port}.
+@xref{gdb_port,,command gdb_port}.
@end itemize
@end deffn
supported.}
@end deffn
+@deffn {Flash Driver} esirisc
+Members of the eSi-RISC family may optionally include internal flash programmed
+via the eSi-TSMC Flash interface. Additional parameters are required to
+configure the driver: @option{cfg_address} is the base address of the
+configuration register interface, @option{clock_hz} is the expected clock
+frequency, and @option{wait_states} is the number of configured read wait states.
+
+@example
+flash bank $_FLASHNAME esirisc base_address size_bytes 0 0 $_TARGETNAME cfg_address clock_hz wait_states
+@end example
+
+@deffn Command {esirisc_flash mass_erase} (bank_id)
+Erases all pages in data memory for the bank identified by @option{bank_id}.
+@end deffn
+
+@deffn Command {esirisc_flash ref_erase} (bank_id)
+Erases the reference cell for the bank identified by @option{bank_id}. This is
+an uncommon operation.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} fm3
All members of the FM3 microcontroller family from Fujitsu
include internal flash and use ARM Cortex-M3 cores.
Some stm32f1x-specific commands are defined:
@deffn Command {stm32f1x lock} num
-Locks the entire stm32 device.
+Locks the entire stm32 device against reading.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@deffn Command {stm32f1x unlock} num
-Unlocks the entire stm32 device.
+Unlocks the entire stm32 device for reading. This command will cause
+a mass erase of the entire stm32 device if previously locked.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@deffn Command {stm32f1x mass_erase} num
-Mass erases the entire stm32f1x device.
+Mass erases the entire stm32 device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
@deffn Command {stm32f1x options_read} num
-Read and display the stm32 option bytes written by
-the @command{stm32f1x options_write} command.
+Reads and displays active stm32 option bytes loaded during POR
+or upon executing the @command{stm32f1x options_load} command.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
Writes the stm32 option byte with the specified values.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+
+@deffn Command {stm32f1x options_load} num
+Generates a special kind of reset to re-load the stm32 option bytes written
+by the @command{stm32f1x options_write} or @command{flash protect} commands
+without having to power cycle the target. Not applicable to stm32f1x devices.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
@end deffn
@deffn {Flash Driver} stm32f2x
Mass erases the entire stm32l4x device.
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+
+@deffn Command {stm32l4x option_read} num reg_offset
+Reads an option byte register from the stm32l4x device.
+The @var{num} parameter is a value shown by @command{flash banks}, @var{reg_offset}
+is the register offset of the Option byte to read.
+
+For example to read the FLASH_OPTR register:
+@example
+stm32l4x option_read 0 0x20
+# Option Register: <0x40022020> = 0xffeff8aa
+@end example
+
+The above example will read out the FLASH_OPTR register which contains the RDP
+option byte, Watchdog configuration, BOR level etc.
+@end deffn
+
+@deffn Command {stm32l4x option_write} num reg_offset reg_mask
+Write an option byte register of the stm32l4x device.
+The @var{num} parameter is a value shown by @command{flash banks}, @var{reg_offset}
+is the register offset of the Option byte to write, and @var{reg_mask} is the mask
+to apply when writing the register (only bits with a '1' will be touched).
+
+For example to write the WRP1AR option bytes:
+@example
+stm32l4x option_write 0 0x28 0x00FF0000 0x00FF00FF
+@end example
+
+The above example will write the WRP1AR option register configuring the Write protection
+Area A for bank 1. The above example set WRP1AR_END=255, WRP1AR_START=0.
+This will effectively write protect all sectors in flash bank 1.
+@end deffn
+
+@deffn Command {stm32l4x option_load} num
+Forces a re-load of the option byte registers. Will cause a reset of the device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
@end deffn
@deffn {Flash Driver} str7x
configure l2x cache
@end deffn
+@deffn Command {cortex_a mmu dump} [@option{0}|@option{1}|@option{addr} address [@option{num_entries}]]
+Dump the MMU translation table from TTB0 or TTB1 register, or from physical
+memory location @var{address}. When dumping the table from @var{address}, print at most
+@var{num_entries} page table entries. @var{num_entries} is optional, if omitted, the maximum
+possible (4096) entries are printed.
+@end deffn
@subsection ARMv7-R specific commands
@cindex Cortex-R
@item @code{itmdump -f /dev/ttyUSB1 -d1}
@item OpenOCD invocation line:
@example
-openocd -f interface/stlink-v2-1.cfg \
+openocd -f interface/stlink.cfg \
-c "transport select hla_swd" \
-f target/stm32l1.cfg \
-c "tpiu config external uart off 24000000 12000000"
@deffn Command {cortex_m maskisr} (@option{auto}|@option{on}|@option{off})
Control masking (disabling) interrupts during target step/resume.
-The @option{auto} option handles interrupts during stepping a way they get
-served but don't disturb the program flow. The step command first allows
+The @option{auto} option handles interrupts during stepping in a way that they
+get served but don't disturb the program flow. The step command first allows
pending interrupt handlers to execute, then disables interrupts and steps over
the next instruction where the core was halted. After the step interrupts
are enabled again. If the interrupt handlers don't complete within 500ms,
@option{on}.
@end deffn
+@section EnSilica eSi-RISC Architecture
+
+eSi-RISC is a highly configurable microprocessor architecture for embedded systems
+provided by EnSilica. (See: @url{http://www.ensilica.com/risc-ip/}.)
+
+@subsection esirisc specific commands
+@deffn Command {esirisc cache_arch} (@option{harvard}|@option{von_neumann})
+Configure the caching architecture. Targets with the @code{UNIFIED_ADDRESS_SPACE}
+option disabled employ a Harvard architecture. By default, @option{von_neumann} is assumed.
+@end deffn
+
+@deffn Command {esirisc flush_caches}
+Flush instruction and data caches. This command requires that the target is halted
+when the command is issued and configured with an instruction or data cache.
+@end deffn
+
+@deffn Command {esirisc hwdc} (@option{all}|@option{none}|mask ...)
+Configure hardware debug control. The HWDC register controls which exceptions return
+control back to the debugger. Possible masks are @option{all}, @option{none},
+@option{reset}, @option{interrupt}, @option{syscall}, @option{error}, and @option{debug}.
+By default, @option{reset}, @option{error}, and @option{debug} are enabled.
+@end deffn
+
@section Intel Architecture
Intel Quark X10xx is the first product in the Quark family of SoCs. It is an IA-32
@section RISC-V Architecture
@uref{http://riscv.org/, RISC-V} is a free and open ISA. OpenOCD supports JTAG
-debug of targets that implement version 0.11 and 0.13 of the RISC-V Debug
-Specification.
+debug of RV32 and RV64 cores in heterogeneous multicore systems of up to 32
+harts. (It's possible to increase this limit to 1024 by changing
+RISCV_MAX_HARTS in riscv.h.) OpenOCD primarily supports 0.13 of the RISC-V
+Debug Specification, but there is also support for legacy targets that
+implement version 0.11.
@subsection RISC-V Terminology
@item @option{embKernel}
@item @option{mqx}
@item @option{uCOS-III}
+@item @option{nuttx}
@end itemize
@quotation Note
_mqx_kernel_data, MQX_init_struct.
@item uC/OS-III symbols
OSRunning, OSTCBCurPtr, OSTaskDbgListPtr, OSTaskQty
+@item nuttx symbols
+g_readytorun, g_tasklisttable
@end table
For most RTOS supported the above symbols will be exported by default. However for
Code Review / openocd.git / blobdiff