* Architecture and Core Commands:: Architecture and Core Commands
* JTAG Commands:: JTAG Commands
* Boundary Scan Commands:: Boundary Scan Commands
+* Utility Commands:: Utility Commands
* TFTP:: TFTP
* GDB and OpenOCD:: Using GDB and OpenOCD
* Tcl Scripting API:: Tcl Scripting API
@unnumbered About
@cindex about
-OpenOCD was created by Dominic Rath as part of a diploma thesis written at the
-University of Applied Sciences Augsburg (@uref{http://www.fh-augsburg.de}).
+OpenOCD was created by Dominic Rath as part of a 2005 diploma thesis written
+at the University of Applied Sciences Augsburg (@uref{http://www.hs-augsburg.de}).
Since that time, the project has grown into an active open-source project,
supported by a diverse community of software and hardware developers from
around the world.
These adapters are sometimes packaged as discrete dongles, which
may generically be called @dfn{hardware interface dongles}.
Some development boards also integrate them directly, which may
-let the development board can be directly connected to the debug
+let the development board connect directly to the debug
host over USB (and sometimes also to power it over USB).
For example, a @dfn{JTAG Adapter} supports JTAG
There are also @dfn{SWD Adapters} that support Serial Wire Debug (SWD)
signaling to communicate with some newer ARM cores, as well as debug
-adapters which support both JTAG and SWD transports. SWD only supports
+adapters which support both JTAG and SWD transports. SWD supports only
debugging, whereas JTAG also supports boundary scan operations.
For some chips, there are also @dfn{Programming Adapters} supporting
(At this writing, OpenOCD does not support such non-debug adapters.)
-@b{Dongles:} OpenOCD currently supports many types of hardware dongles: USB
-based, parallel port based, and other standalone boxes that run
+@b{Dongles:} OpenOCD currently supports many types of hardware dongles:
+USB-based, parallel port-based, and other standalone boxes that run
OpenOCD internally. @xref{Debug Adapter Hardware}.
@b{GDB Debug:} It allows ARM7 (ARM7TDMI and ARM720t), ARM9 (ARM920T,
-ARM922T, ARM926EJ--S, ARM966E--S), XScale (PXA25x, IXP42x) and
-Cortex-M3 (Stellaris LM3, ST STM32 and Energy Micro EFM32) based cores to be
-debugged via the GDB protocol.
+ARM922T, ARM926EJ--S, ARM966E--S), XScale (PXA25x, IXP42x), Cortex-M3
+(Stellaris LM3, ST STM32 and Energy Micro EFM32) and Intel Quark (x10xx)
+based cores to be debugged via the GDB protocol.
-@b{Flash Programing:} Flash writing is supported for external CFI
-compatible NOR flashes (Intel and AMD/Spansion command set) and several
-internal flashes (LPC1700, LPC2000, AT91SAM7, AT91SAM3U, STR7x, STR9x, LM3,
-STM32x and EFM32). Preliminary support for various NAND flash controllers
-(LPC3180, Orion, S3C24xx, more) controller is included.
+@b{Flash Programming:} Flash writing is supported for external
+CFI-compatible NOR flashes (Intel and AMD/Spansion command set) and several
+internal flashes (LPC1700, LPC1800, LPC2000, LPC4300, AT91SAM7, AT91SAM3U,
+STR7x, STR9x, LM3, STM32x and EFM32). Preliminary support for various NAND flash
+controllers (LPC3180, Orion, S3C24xx, more) is included.
@section OpenOCD Web Site
The resources in this chapter are available for developers wishing to explore
or expand the OpenOCD source code.
-@section OpenOCD GIT Repository
+@section OpenOCD Git Repository
During the 0.3.x release cycle, OpenOCD switched from Subversion to
-a GIT repository hosted at SourceForge. The repository URL is:
+a Git repository hosted at SourceForge. The repository URL is:
-@uref{git://openocd.git.sourceforge.net/gitroot/openocd/openocd}
+@uref{git://git.code.sf.net/p/openocd/code}
+
+or via http
+
+@uref{http://git.code.sf.net/p/openocd/code}
You may prefer to use a mirror and the HTTP protocol:
@uref{http://repo.or.cz/r/openocd.git}
-With standard GIT tools, use @command{git clone} to initialize
+With standard Git tools, use @command{git clone} to initialize
a local repository, and @command{git pull} to update it.
There are also gitweb pages letting you browse the repository
with a web browser, or download arbitrary snapshots without
-needing a GIT client:
-
-@uref{http://openocd.git.sourceforge.net/git/gitweb.cgi?p=openocd/openocd}
+needing a Git client:
@uref{http://repo.or.cz/w/openocd.git}
This document is a work-in-progress, but contributions would be welcome
to fill in the gaps. All of the source files are provided in-tree,
-listed in the Doxyfile configuration in the top of the source tree.
+listed in the Doxyfile configuration at the top of the source tree.
+
+@section Gerrit Review System
+
+All changes in the OpenOCD Git repository go through the web-based Gerrit
+Code Review System:
+
+@uref{http://openocd.zylin.com/}
+
+After a one-time registration and repository setup, anyone can push commits
+from their local Git repository directly into Gerrit.
+All users and developers are encouraged to review, test, discuss and vote
+for changes in Gerrit. The feedback provides the basis for a maintainer to
+eventually submit the change to the main Git repository.
+
+The @file{HACKING} file, also available as the Patch Guide in the Doxygen
+Developer Manual, contains basic information about how to connect a
+repository to Gerrit, prepare and push patches. Patch authors are expected to
+maintain their changes while they're in Gerrit, respond to feedback and if
+necessary rework and push improved versions of the change.
@section OpenOCD Developer Mailing List
@uref{https://lists.sourceforge.net/mailman/listinfo/openocd-devel}
-Discuss and submit patches to this list.
-The @file{HACKING} file contains basic information about how
-to prepare patches.
-
-@section OpenOCD Bug Database
+@section OpenOCD Bug Tracker
-During the 0.4.x release cycle the OpenOCD project team began
-using Trac for its bug database:
+The OpenOCD Bug Tracker is hosted on SourceForge:
-@uref{https://sourceforge.net/apps/trac/openocd}
+@uref{https://sourceforge.net/p/openocd/tickets/}
@node Debug Adapter Hardware
@cindex USB Adapter
@cindex RTCK
-Defined: @b{dongle}: A small device that plugins into a computer and serves as
+Defined: @b{dongle}: A small device that plugs into a computer and serves as
an adapter .... [snip]
In the OpenOCD case, this generally refers to @b{a small adapter} that
-attaches to your computer via USB or the Parallel Printer Port. One
-exception is the Zylin ZY1000, packaged as a small box you attach via
-an ethernet cable. The Zylin ZY1000 has the advantage that it does not
+attaches to your computer via USB or the parallel port. One
+exception is the Ultimate Solutions ZY1000, packaged as a small box you
+attach via an ethernet cable. The ZY1000 has the advantage that it does not
require any drivers to be installed on the developer PC. It also has
a built in web interface. It supports RTCK/RCLK or adaptive clocking
-and has a built in relay to power cycle targets remotely.
+and has a built-in relay to power cycle targets remotely.
@section Choosing a Dongle
@item @b{Pinout} What pinout does your target board use?
Does your dongle support it? You may be able to use jumper
wires, or an "octopus" connector, to convert pinouts.
-@item @b{Connection} Does your computer have the USB, printer, or
+@item @b{Connection} Does your computer have the USB, parallel, or
Ethernet port needed?
@item @b{RTCK} Do you expect to use it with ARM chips and boards with
-RTCK support? Also known as ``adaptive clocking''
+RTCK support (also known as ``adaptive clocking'')?
@end enumerate
-@section Stand alone Systems
+@section Stand-alone JTAG Probe
-@b{ZY1000} See: @url{http://www.ultsol.com/index.php/component/content/article/8/33-zylin-zy1000-jtag-probe}
-Technically, not a dongle, but a standalone box. The ZY1000 has the advantage that it does
-not require any drivers installed on the developer PC. It also has
-a built in web interface. It supports RTCK/RCLK or adaptive clocking
-and has a built in relay to power cycle targets remotely.
+The ZY1000 from Ultimate Solutions is technically not a dongle but a
+stand-alone JTAG probe that, unlike most dongles, doesn't require any drivers
+running on the developer's host computer.
+Once installed on a network using DHCP or a static IP assignment, users can
+access the ZY1000 probe locally or remotely from any host with access to the
+IP address assigned to the probe.
+The ZY1000 provides an intuitive web interface with direct access to the
+OpenOCD debugger.
+Users may also run a GDBSERVER directly on the ZY1000 to take full advantage
+of GCC & GDB to debug any distribution of embedded Linux or NetBSD running on
+the target.
+The ZY1000 supports RTCK & RCLK or adaptive clocking and has a built-in relay
+to power cycle the target remotely.
+
+For more information, visit:
+
+@b{ZY1000} See: @url{http://www.ultsol.com/index.php/component/content/article/8/210-zylin-zy1000-main}
@section USB FT2232 Based
-There are many USB JTAG dongles on the market, many of them are based
+There are many USB JTAG dongles on the market, many of them based
on a chip from ``Future Technology Devices International'' (FTDI)
known as the FTDI FT2232; this is a USB full speed (12 Mbps) chip.
See: @url{http://www.ftdichip.com} for more information.
In summer 2009, USB high speed (480 Mbps) versions of these FTDI
-chips are starting to become available in JTAG adapters. (Adapters
-using those high speed FT2232H chips may support adaptive clocking.)
+chips started to become available in JTAG adapters. Around 2012, a new
+variant appeared - FT232H - this is a single-channel version of FT2232H.
+(Adapters using those high speed FT2232H or FT232H chips may support adaptive
+clocking.)
The FT2232 chips are flexible enough to support some other
transport options, such as SWD or the SPI variants used to
other one is used to provide a debug adapter.
Also, some development boards integrate an FT2232 chip to serve as
-a built-in low cost debug adapter and usb-to-serial solution.
+a built-in low-cost debug adapter and USB-to-serial solution.
@itemize @bullet
@item @b{usbjtag}
@item @b{opendous}
@* Link @url{http://code.google.com/p/opendous/wiki/JTAG} FT2232H-based
(OpenHardware).
-@end itemize
+@item @b{JTAG-lock-pick Tiny 2}
+@* Link @url{http://www.distortec.com/jtag-lock-pick-tiny-2} FT232H-based
+
+@item @b{GW16042}
+@* Link: @url{http://shop.gateworks.com/index.php?route=product/product&path=70_80&product_id=64}
+FT2232H-based
+@end itemize
@section USB-JTAG / Altera USB-Blaster compatibles
These devices also show up as FTDI devices, but are not
protocol-compatible with the FT2232 devices. They are, however,
protocol-compatible among themselves. USB-JTAG devices typically consist
of a FT245 followed by a CPLD that understands a particular protocol,
-or emulate this protocol using some other hardware.
+or emulates this protocol using some other hardware.
They may appear under different USB VID/PID depending on the particular
product. The driver can be configured to search for any VID/PID pair
@* Link: @url{http://www.st.com/internet/evalboard/product/251168.jsp}
@end itemize
-For info the original ST-LINK enumerates using the mass storage usb class, however
-it's implementation is completely broken. The result is this causes issues under linux.
-The simplest solution is to get linux to ignore the ST-LINK using one of the following methods:
+For info the original ST-LINK enumerates using the mass storage usb class; however,
+its implementation is completely broken. The result is this causes issues under Linux.
+The simplest solution is to get Linux to ignore the ST-LINK using one of the following methods:
@itemize @bullet
@item modprobe -r usb-storage && modprobe usb-storage quirks=483:3744:i
@item add "options usb-storage quirks=483:3744:i" to /etc/modprobe.conf
It is not to be confused with the FTDI based adapters that were originally fitted to their
evaluation boards. This is the adapter fitted to the Stellaris LaunchPad.
+@section USB CMSIS-DAP based
+ARM has released a interface standard called CMSIS-DAP that simplifies connecting
+debuggers to ARM Cortex based targets @url{http://www.keil.com/support/man/docs/dapdebug/dapdebug_introduction.htm}.
+
@section USB Other
@itemize @bullet
@item @b{USBprog}
@section IBM PC Parallel Printer Port Based
-The two well known ``JTAG Parallel Ports'' cables are the Xilnx DLC5
+The two well-known ``JTAG Parallel Ports'' cables are the Xilinx DLC5
and the Macraigor Wiggler. There are many clones and variations of
these on the market.
@item @b{Amontec - JTAG Accelerator}
@* Link: @url{http://www.amontec.com/jtag_accelerator.shtml}
-@item @b{GW16402}
-@* Link: @url{http://www.gateworks.com/products/avila_accessories/gw16042.php}
-
@item @b{Wiggler2}
@* Link: @url{http://www.ccac.rwth-aachen.de/~michaels/index.php/hardware/armjtag}
@item @b{at91rm9200}
@* Like the EP93xx - but an ATMEL AT91RM9200 based solution using the GPIO pins on the chip.
+@item @b{bcm2835gpio}
+@* A BCM2835-based board (e.g. Raspberry Pi) using the GPIO pins of the expansion header.
+
+@item @b{jtag_vpi}
+@* A JTAG driver acting as a client for the JTAG VPI server interface.
+@* Link: @url{http://github.com/fjullien/jtag_vpi}
+
@end itemize
@node About Jim-Tcl
All commands presented in this Guide are extensions to Jim-Tcl.
You can use them as simple commands, without needing to learn
much of anything about Tcl.
-Alternatively, can write Tcl programs with them.
+Alternatively, you can write Tcl programs with them.
-You can learn more about Jim at its website, @url{http://jim.berlios.de}.
+You can learn more about Jim at its website, @url{http://jim.tcl.tk}.
There is an active and responsive community, get on the mailing list
if you have any questions. Jim-Tcl maintainers also lurk on the
OpenOCD mailing list.
@item @b{Scripts}
@* OpenOCD configuration scripts are Jim-Tcl Scripts. OpenOCD's
command interpreter today is a mixture of (newer)
-Jim-Tcl commands, and (older) the orginal command interpreter.
+Jim-Tcl commands, and the (older) original command interpreter.
@item @b{Commands}
@* At the OpenOCD telnet command line (or via the GDB monitor command) one
@item @b{Historical Note}
@* Jim-Tcl was introduced to OpenOCD in spring 2008. Fall 2010,
-before OpenOCD 0.5 release OpenOCD switched to using Jim Tcl
-as a git submodule, which greatly simplified upgrading Jim Tcl
-to benefit from new features and bugfixes in Jim Tcl.
+before OpenOCD 0.5 release, OpenOCD switched to using Jim-Tcl
+as a Git submodule, which greatly simplified upgrading Jim-Tcl
+to benefit from new features and bugfixes in Jim-Tcl.
@item @b{Need a crash course in Tcl?}
@*@xref{Tcl Crash Course}.
Properly installing OpenOCD sets up your operating system to grant it access
to the debug adapters. On Linux, this usually involves installing a file
-in @file{/etc/udev/rules.d,} so OpenOCD has permissions. MS-Windows needs
+in @file{/etc/udev/rules.d,} so OpenOCD has permissions. An example rules file
+that works for many common adapters is shipped with OpenOCD in the
+@file{contrib} directory. MS-Windows needs
complex and confusing driver configuration for every peripheral. Such issues
are unique to each operating system, and are not detailed in this User's Guide.
If you find a script for your JTAG adapter, and for your board or
target, you may be able to hook up your JTAG adapter then start
-the server like:
+the server with some variation of one of the following:
@example
openocd -f interface/ADAPTER.cfg -f board/MYBOARD.cfg
+openocd -f interface/ftdi/ADAPTER.cfg -f board/MYBOARD.cfg
@end example
You might also need to configure which reset signals are present,
@chapter OpenOCD Project Setup
To use OpenOCD with your development projects, you need to do more than
-just connecting the JTAG adapter hardware (dongle) to your development board
-and then starting the OpenOCD server.
-You also need to configure that server so that it knows
-about that adapter and board, and helps your work.
+just connect the JTAG adapter hardware (dongle) to your development board
+and start the OpenOCD server.
+You also need to configure your OpenOCD server so that it knows
+about your adapter and board, and helps your work.
You may also want to connect OpenOCD to GDB, possibly
using Eclipse or some other GUI.
you are using to run OpenOCD.
For Ethernet, consult the documentation and your network administrator.
-For USB based JTAG adapters you have an easy sanity check at this point:
-does the host operating system see the JTAG adapter? If that host is an
+For USB-based JTAG adapters you have an easy sanity check at this point:
+does the host operating system see the JTAG adapter? If you're running
+Linux, try the @command{lsusb} command. If that host is an
MS-Windows host, you'll need to install a driver before OpenOCD works.
@item @emph{Connect the adapter's power supply, if needed.}
@item
You may may need to write some C code.
-It may be as simple as a supporting a new ft2232 or parport
+It may be as simple as supporting a new FT2232 or parport
based adapter; a bit more involved, like a NAND or NOR flash
controller driver; or a big piece of work like supporting
a new chip architecture.
Likewise, the @command{arm9 vector_catch} command (or
@cindex vector_catch
its siblings @command{xscale vector_catch}
-and @command{cortex_m3 vector_catch}) can be a timesaver
+and @command{cortex_m vector_catch}) can be a timesaver
during some debug sessions, but don't make everyone use that either.
Keep those kinds of debugging aids in your user config file,
along with messaging and tracing setup.
These are for debug adapters.
Files that configure JTAG adapters go here.
@example
-$ ls interface
-altera-usb-blaster.cfg hilscher_nxhx50_etm.cfg openrd.cfg
-arm-jtag-ew.cfg hilscher_nxhx50_re.cfg osbdm.cfg
-arm-usb-ocd.cfg hitex_str9-comstick.cfg parport.cfg
-at91rm9200.cfg icebear.cfg parport_dlc5.cfg
-axm0432.cfg jlink.cfg redbee-econotag.cfg
-busblaster.cfg jtagkey2.cfg redbee-usb.cfg
-buspirate.cfg jtagkey2p.cfg rlink.cfg
-calao-usb-a9260-c01.cfg jtagkey.cfg sheevaplug.cfg
-calao-usb-a9260-c02.cfg jtagkey-tiny.cfg signalyzer.cfg
-calao-usb-a9260.cfg kt-link.cfg signalyzer-h2.cfg
-chameleon.cfg lisa-l.cfg signalyzer-h4.cfg
-cortino.cfg luminary.cfg signalyzer-lite.cfg
-digilent-hs1.cfg luminary-icdi.cfg stlink-v1.cfg
-dlp-usb1232h.cfg luminary-lm3s811.cfg stlink-v2.cfg
-dummy.cfg minimodule.cfg stm32-stick.cfg
-estick.cfg neodb.cfg turtelizer2.cfg
-flashlink.cfg ngxtech.cfg ulink.cfg
-flossjtag.cfg olimex-arm-usb-ocd.cfg usb-jtag.cfg
-flossjtag-noeeprom.cfg olimex-arm-usb-ocd-h.cfg usbprog.cfg
-flyswatter2.cfg olimex-arm-usb-tiny-h.cfg vpaclink.cfg
-flyswatter.cfg olimex-jtag-tiny.cfg vsllink.cfg
-hilscher_nxhx10_etm.cfg oocdlink.cfg xds100v2.cfg
-hilscher_nxhx500_etm.cfg opendous.cfg
-hilscher_nxhx500_re.cfg openocd-usb.cfg
+$ ls interface -R
+interface/:
+altera-usb-blaster.cfg hilscher_nxhx50_re.cfg openocd-usb-hs.cfg
+arm-jtag-ew.cfg hitex_str9-comstick.cfg openrd.cfg
+at91rm9200.cfg icebear.cfg osbdm.cfg
+axm0432.cfg jlink.cfg parport.cfg
+busblaster.cfg jtagkey2.cfg parport_dlc5.cfg
+buspirate.cfg jtagkey2p.cfg redbee-econotag.cfg
+calao-usb-a9260-c01.cfg jtagkey.cfg redbee-usb.cfg
+calao-usb-a9260-c02.cfg jtagkey-tiny.cfg rlink.cfg
+calao-usb-a9260.cfg jtag-lock-pick_tiny_2.cfg sheevaplug.cfg
+chameleon.cfg kt-link.cfg signalyzer.cfg
+cortino.cfg lisa-l.cfg signalyzer-h2.cfg
+digilent-hs1.cfg luminary.cfg signalyzer-h4.cfg
+dlp-usb1232h.cfg luminary-icdi.cfg signalyzer-lite.cfg
+dummy.cfg luminary-lm3s811.cfg stlink-v1.cfg
+estick.cfg minimodule.cfg stlink-v2.cfg
+flashlink.cfg neodb.cfg stm32-stick.cfg
+flossjtag.cfg ngxtech.cfg sysfsgpio-raspberrypi.cfg
+flossjtag-noeeprom.cfg olimex-arm-usb-ocd.cfg ti-icdi.cfg
+flyswatter2.cfg olimex-arm-usb-ocd-h.cfg turtelizer2.cfg
+flyswatter.cfg olimex-arm-usb-tiny-h.cfg ulink.cfg
+ftdi olimex-jtag-tiny.cfg usb-jtag.cfg
+hilscher_nxhx10_etm.cfg oocdlink.cfg usbprog.cfg
+hilscher_nxhx500_etm.cfg opendous.cfg vpaclink.cfg
+hilscher_nxhx500_re.cfg opendous_ftdi.cfg vsllink.cfg
+hilscher_nxhx50_etm.cfg openocd-usb.cfg xds100v2.cfg
+
+interface/ftdi:
+axm0432.cfg hitex_str9-comstick.cfg olimex-jtag-tiny.cfg
+calao-usb-a9260-c01.cfg icebear.cfg oocdlink.cfg
+calao-usb-a9260-c02.cfg jtagkey2.cfg opendous_ftdi.cfg
+cortino.cfg jtagkey2p.cfg openocd-usb.cfg
+dlp-usb1232h.cfg jtagkey.cfg openocd-usb-hs.cfg
+dp_busblaster.cfg jtag-lock-pick_tiny_2.cfg openrd.cfg
+flossjtag.cfg kt-link.cfg redbee-econotag.cfg
+flossjtag-noeeprom.cfg lisa-l.cfg redbee-usb.cfg
+flyswatter2.cfg luminary.cfg sheevaplug.cfg
+flyswatter.cfg luminary-icdi.cfg signalyzer.cfg
+gw16042.cfg luminary-lm3s811.cfg signalyzer-lite.cfg
+hilscher_nxhx10_etm.cfg minimodule.cfg stm32-stick.cfg
+hilscher_nxhx500_etm.cfg neodb.cfg turtelizer2-revB.cfg
+hilscher_nxhx500_re.cfg ngxtech.cfg turtelizer2-revC.cfg
+hilscher_nxhx50_etm.cfg olimex-arm-usb-ocd.cfg vpaclink.cfg
+hilscher_nxhx50_re.cfg olimex-arm-usb-ocd-h.cfg xds100v2.cfg
+hitex_lpc1768stick.cfg olimex-arm-usb-tiny-h.cfg
$
@end example
@item @file{board} ...
a CPU and an FPGA.
@example
$ ls board
-actux3.cfg logicpd_imx27.cfg
-am3517evm.cfg lubbock.cfg
-arm_evaluator7t.cfg mcb1700.cfg
-at91cap7a-stk-sdram.cfg microchip_explorer16.cfg
-at91eb40a.cfg mini2440.cfg
-at91rm9200-dk.cfg mini6410.cfg
-at91rm9200-ek.cfg olimex_LPC2378STK.cfg
-at91sam9261-ek.cfg olimex_lpc_h2148.cfg
-at91sam9263-ek.cfg olimex_sam7_ex256.cfg
-at91sam9g20-ek.cfg olimex_sam9_l9260.cfg
-atmel_at91sam7s-ek.cfg olimex_stm32_h103.cfg
-atmel_at91sam9260-ek.cfg olimex_stm32_h107.cfg
-atmel_at91sam9rl-ek.cfg olimex_stm32_p107.cfg
-atmel_sam3n_ek.cfg omap2420_h4.cfg
-atmel_sam3s_ek.cfg open-bldc.cfg
-atmel_sam3u_ek.cfg openrd.cfg
-atmel_sam3x_ek.cfg osk5912.cfg
-atmel_sam4s_ek.cfg phytec_lpc3250.cfg
-balloon3-cpu.cfg pic-p32mx.cfg
-colibri.cfg propox_mmnet1001.cfg
-crossbow_tech_imote2.cfg pxa255_sst.cfg
-csb337.cfg redbee.cfg
-csb732.cfg rsc-w910.cfg
-da850evm.cfg sheevaplug.cfg
-digi_connectcore_wi-9c.cfg smdk6410.cfg
-diolan_lpc4350-db1.cfg spear300evb.cfg
-dm355evm.cfg spear300evb_mod.cfg
-dm365evm.cfg spear310evb20.cfg
-dm6446evm.cfg spear310evb20_mod.cfg
-efikamx.cfg spear320cpu.cfg
-eir.cfg spear320cpu_mod.cfg
-ek-lm3s1968.cfg steval_pcc010.cfg
-ek-lm3s3748.cfg stm320518_eval_stlink.cfg
-ek-lm3s6965.cfg stm32100b_eval.cfg
-ek-lm3s811.cfg stm3210b_eval.cfg
-ek-lm3s811-revb.cfg stm3210c_eval.cfg
-ek-lm3s9b9x.cfg stm3210e_eval.cfg
+actux3.cfg lpc1850_spifi_generic.cfg
+am3517evm.cfg lpc4350_spifi_generic.cfg
+arm_evaluator7t.cfg lubbock.cfg
+at91cap7a-stk-sdram.cfg mcb1700.cfg
+at91eb40a.cfg microchip_explorer16.cfg
+at91rm9200-dk.cfg mini2440.cfg
+at91rm9200-ek.cfg mini6410.cfg
+at91sam9261-ek.cfg netgear-dg834v3.cfg
+at91sam9263-ek.cfg olimex_LPC2378STK.cfg
+at91sam9g20-ek.cfg olimex_lpc_h2148.cfg
+atmel_at91sam7s-ek.cfg olimex_sam7_ex256.cfg
+atmel_at91sam9260-ek.cfg olimex_sam9_l9260.cfg
+atmel_at91sam9rl-ek.cfg olimex_stm32_h103.cfg
+atmel_sam3n_ek.cfg olimex_stm32_h107.cfg
+atmel_sam3s_ek.cfg olimex_stm32_p107.cfg
+atmel_sam3u_ek.cfg omap2420_h4.cfg
+atmel_sam3x_ek.cfg open-bldc.cfg
+atmel_sam4s_ek.cfg openrd.cfg
+balloon3-cpu.cfg osk5912.cfg
+colibri.cfg phone_se_j100i.cfg
+crossbow_tech_imote2.cfg phytec_lpc3250.cfg
+csb337.cfg pic-p32mx.cfg
+csb732.cfg propox_mmnet1001.cfg
+da850evm.cfg pxa255_sst.cfg
+digi_connectcore_wi-9c.cfg redbee.cfg
+diolan_lpc4350-db1.cfg rsc-w910.cfg
+dm355evm.cfg sheevaplug.cfg
+dm365evm.cfg smdk6410.cfg
+dm6446evm.cfg spear300evb.cfg
+efikamx.cfg spear300evb_mod.cfg
+eir.cfg spear310evb20.cfg
+ek-lm3s1968.cfg spear310evb20_mod.cfg
+ek-lm3s3748.cfg spear320cpu.cfg
+ek-lm3s6965.cfg spear320cpu_mod.cfg
+ek-lm3s811.cfg steval_pcc010.cfg
+ek-lm3s811-revb.cfg stm320518_eval_stlink.cfg
+ek-lm3s8962.cfg stm32100b_eval.cfg
+ek-lm3s9b9x.cfg stm3210b_eval.cfg
+ek-lm3s9d92.cfg stm3210c_eval.cfg
+ek-lm4f120xl.cfg stm3210e_eval.cfg
ek-lm4f232.cfg stm3220g_eval.cfg
embedded-artists_lpc2478-32.cfg stm3220g_eval_stlink.cfg
ethernut3.cfg stm3241g_eval.cfg
glyn_tonga2.cfg stm3241g_eval_stlink.cfg
hammer.cfg stm32f0discovery.cfg
-hilscher_nxdb500sys.cfg stm32f4discovery.cfg
-hilscher_nxeb500hmi.cfg stm32ldiscovery.cfg
-hilscher_nxhx10.cfg stm32vldiscovery.cfg
-hilscher_nxhx500.cfg str910-eval.cfg
-hilscher_nxhx50.cfg telo.cfg
-hilscher_nxsb100.cfg ti_beagleboard.cfg
-hitex_lpc2929.cfg ti_beagleboard_xm.cfg
-hitex_stm32-performancestick.cfg ti_beaglebone.cfg
-hitex_str9-comstick.cfg ti_blaze.cfg
-iar_lpc1768.cfg ti_pandaboard.cfg
-iar_str912_sk.cfg ti_pandaboard_es.cfg
-icnova_imx53_sodimm.cfg topas910.cfg
-icnova_sam9g45_sodimm.cfg topasa900.cfg
-imx27ads.cfg twr-k60n512.cfg
-imx27lnst.cfg tx25_stk5.cfg
-imx28evk.cfg tx27_stk5.cfg
-imx31pdk.cfg unknown_at91sam9260.cfg
-imx35pdk.cfg uptech_2410.cfg
-imx53loco.cfg verdex.cfg
-keil_mcb1700.cfg voipac.cfg
-keil_mcb2140.cfg voltcraft_dso-3062c.cfg
-kwikstik.cfg x300t.cfg
-linksys_nslu2.cfg zy1000.cfg
-lisa-l.cfg
+hilscher_nxdb500sys.cfg stm32f3discovery.cfg
+hilscher_nxeb500hmi.cfg stm32f4discovery.cfg
+hilscher_nxhx10.cfg stm32ldiscovery.cfg
+hilscher_nxhx500.cfg stm32vldiscovery.cfg
+hilscher_nxhx50.cfg str910-eval.cfg
+hilscher_nxsb100.cfg telo.cfg
+hitex_lpc1768stick.cfg ti_am335xevm.cfg
+hitex_lpc2929.cfg ti_beagleboard.cfg
+hitex_stm32-performancestick.cfg ti_beagleboard_xm.cfg
+hitex_str9-comstick.cfg ti_beaglebone.cfg
+iar_lpc1768.cfg ti_blaze.cfg
+iar_str912_sk.cfg ti_pandaboard.cfg
+icnova_imx53_sodimm.cfg ti_pandaboard_es.cfg
+icnova_sam9g45_sodimm.cfg topas910.cfg
+imx27ads.cfg topasa900.cfg
+imx27lnst.cfg twr-k60f120m.cfg
+imx28evk.cfg twr-k60n512.cfg
+imx31pdk.cfg tx25_stk5.cfg
+imx35pdk.cfg tx27_stk5.cfg
+imx53loco.cfg unknown_at91sam9260.cfg
+keil_mcb1700.cfg uptech_2410.cfg
+keil_mcb2140.cfg verdex.cfg
+kwikstik.cfg voipac.cfg
+linksys_nslu2.cfg voltcraft_dso-3062c.cfg
+lisa-l.cfg x300t.cfg
+logicpd_imx27.cfg zy1000.cfg
$
@end example
@item @file{target} ...
the target config file defines all of them.
@example
$ ls target
-$duc702x.cfg ixp42x.cfg
-am335x.cfg k40.cfg
-amdm37x.cfg k60.cfg
-ar71xx.cfg lpc1768.cfg
-at32ap7000.cfg lpc2103.cfg
-at91r40008.cfg lpc2124.cfg
-at91rm9200.cfg lpc2129.cfg
-at91sam3ax_4x.cfg lpc2148.cfg
-at91sam3ax_8x.cfg lpc2294.cfg
-at91sam3ax_xx.cfg lpc2378.cfg
-at91sam3nXX.cfg lpc2460.cfg
-at91sam3sXX.cfg lpc2478.cfg
-at91sam3u1c.cfg lpc2900.cfg
-at91sam3u1e.cfg lpc2xxx.cfg
-at91sam3u2c.cfg lpc3131.cfg
-at91sam3u2e.cfg lpc3250.cfg
-at91sam3u4c.cfg lpc4350.cfg
-at91sam3u4e.cfg mc13224v.cfg
-at91sam3uxx.cfg nuc910.cfg
-at91sam3XXX.cfg omap2420.cfg
-at91sam4sXX.cfg omap3530.cfg
-at91sam4XXX.cfg omap4430.cfg
-at91sam7se512.cfg omap4460.cfg
-at91sam7sx.cfg omap5912.cfg
-at91sam7x256.cfg omapl138.cfg
-at91sam7x512.cfg pic32mx.cfg
-at91sam9260.cfg pxa255.cfg
-at91sam9260_ext_RAM_ext_flash.cfg pxa270.cfg
-at91sam9261.cfg pxa3xx.cfg
-at91sam9263.cfg readme.txt
-at91sam9.cfg samsung_s3c2410.cfg
-at91sam9g10.cfg samsung_s3c2440.cfg
-at91sam9g20.cfg samsung_s3c2450.cfg
-at91sam9g45.cfg samsung_s3c4510.cfg
-at91sam9rl.cfg samsung_s3c6410.cfg
-atmega128.cfg sharp_lh79532.cfg
-avr32.cfg smp8634.cfg
-c100.cfg spear3xx.cfg
-c100config.tcl stellaris.cfg
-c100helper.tcl stm32.cfg
-c100regs.tcl stm32f0x_stlink.cfg
-cs351x.cfg stm32f1x.cfg
-davinci.cfg stm32f1x_stlink.cfg
-dragonite.cfg stm32f2x.cfg
-dsp56321.cfg stm32f2x_stlink.cfg
-dsp568013.cfg stm32f2xxx.cfg
-dsp568037.cfg stm32f4x.cfg
-epc9301.cfg stm32f4x_stlink.cfg
-faux.cfg stm32l.cfg
-feroceon.cfg stm32lx_stlink.cfg
-fm3.cfg stm32_stlink.cfg
-hilscher_netx10.cfg stm32xl.cfg
-hilscher_netx500.cfg str710.cfg
-hilscher_netx50.cfg str730.cfg
-icepick.cfg str750.cfg
-imx21.cfg str912.cfg
-imx25.cfg swj-dp.tcl
-imx27.cfg test_reset_syntax_error.cfg
-imx28.cfg test_syntax_error.cfg
-imx31.cfg ti_dm355.cfg
-imx35.cfg ti_dm365.cfg
-imx51.cfg ti_dm6446.cfg
-imx53.cfg tmpa900.cfg
-imx.cfg tmpa910.cfg
-is5114.cfg u8500.cfg
+aduc702x.cfg lpc1764.cfg
+am335x.cfg lpc1765.cfg
+amdm37x.cfg lpc1766.cfg
+ar71xx.cfg lpc1767.cfg
+at32ap7000.cfg lpc1768.cfg
+at91r40008.cfg lpc1769.cfg
+at91rm9200.cfg lpc1788.cfg
+at91sam3ax_4x.cfg lpc17xx.cfg
+at91sam3ax_8x.cfg lpc1850.cfg
+at91sam3ax_xx.cfg lpc2103.cfg
+at91sam3nXX.cfg lpc2124.cfg
+at91sam3sXX.cfg lpc2129.cfg
+at91sam3u1c.cfg lpc2148.cfg
+at91sam3u1e.cfg lpc2294.cfg
+at91sam3u2c.cfg lpc2378.cfg
+at91sam3u2e.cfg lpc2460.cfg
+at91sam3u4c.cfg lpc2478.cfg
+at91sam3u4e.cfg lpc2900.cfg
+at91sam3uxx.cfg lpc2xxx.cfg
+at91sam3XXX.cfg lpc3131.cfg
+at91sam4sd32x.cfg lpc3250.cfg
+at91sam4sXX.cfg lpc4350.cfg
+at91sam4XXX.cfg lpc4350.cfg.orig
+at91sam7se512.cfg mc13224v.cfg
+at91sam7sx.cfg nuc910.cfg
+at91sam7x256.cfg omap2420.cfg
+at91sam7x512.cfg omap3530.cfg
+at91sam9260.cfg omap4430.cfg
+at91sam9260_ext_RAM_ext_flash.cfg omap4460.cfg
+at91sam9261.cfg omap5912.cfg
+at91sam9263.cfg omapl138.cfg
+at91sam9.cfg pic32mx.cfg
+at91sam9g10.cfg pxa255.cfg
+at91sam9g20.cfg pxa270.cfg
+at91sam9g45.cfg pxa3xx.cfg
+at91sam9rl.cfg readme.txt
+atmega128.cfg samsung_s3c2410.cfg
+avr32.cfg samsung_s3c2440.cfg
+c100.cfg samsung_s3c2450.cfg
+c100config.tcl samsung_s3c4510.cfg
+c100helper.tcl samsung_s3c6410.cfg
+c100regs.tcl sharp_lh79532.cfg
+cs351x.cfg sim3x.cfg
+davinci.cfg smp8634.cfg
+dragonite.cfg spear3xx.cfg
+dsp56321.cfg stellaris.cfg
+dsp568013.cfg stellaris_icdi.cfg
+dsp568037.cfg stm32f0x_stlink.cfg
+efm32_stlink.cfg stm32f1x.cfg
+epc9301.cfg stm32f1x_stlink.cfg
+faux.cfg stm32f2x.cfg
+feroceon.cfg stm32f2x_stlink.cfg
+fm3.cfg stm32f3x.cfg
+hilscher_netx10.cfg stm32f3x_stlink.cfg
+hilscher_netx500.cfg stm32f4x.cfg
+hilscher_netx50.cfg stm32f4x_stlink.cfg
+icepick.cfg stm32l.cfg
+imx21.cfg stm32lx_dual_bank.cfg
+imx25.cfg stm32lx_stlink.cfg
+imx27.cfg stm32_stlink.cfg
+imx28.cfg stm32w108_stlink.cfg
+imx31.cfg stm32xl.cfg
+imx35.cfg str710.cfg
+imx51.cfg str730.cfg
+imx53.cfg str750.cfg
+imx6.cfg str912.cfg
+imx.cfg swj-dp.tcl
+is5114.cfg test_reset_syntax_error.cfg
+ixp42x.cfg test_syntax_error.cfg
+k40.cfg ti-ar7.cfg
+k60.cfg ti_calypso.cfg
+lpc1751.cfg ti_dm355.cfg
+lpc1752.cfg ti_dm365.cfg
+lpc1754.cfg ti_dm6446.cfg
+lpc1756.cfg tmpa900.cfg
+lpc1758.cfg tmpa910.cfg
+lpc1759.cfg u8500.cfg
+lpc1763.cfg
@end example
@item @emph{more} ... browse for other library files which may be useful.
For example, there are various generic and CPU-specific utilities.
In summary the board files should contain (if present)
@enumerate
-@item One or more @command{source [target/...cfg]} statements
+@item One or more @command{source [find target/...cfg]} statements
@item NOR flash configuration (@pxref{norconfiguration,,NOR Configuration})
@item NAND flash configuration (@pxref{nandconfiguration,,NAND Configuration})
@item Target @code{reset} handlers for SDRAM and I/O configuration
(@xref{theinittargetsprocedure,,The init_targets procedure}.) - it's a replacement of ``linear''
configuration scripts. This procedure is meant to be executed when OpenOCD enters run stage
(@xref{enteringtherunstage,,Entering the Run Stage},) after @code{init_targets}. The idea to have
-spearate @code{init_targets} and @code{init_board} procedures is to allow the first one to configure
+separate @code{init_targets} and @code{init_board} procedures is to allow the first one to configure
everything target specific (internal flash, internal RAM, etc.) and the second one to configure
everything board specific (reset signals, chip frequency, reset-init event handler, external memory, etc.).
Additionally ``linear'' board config file will most likely fail when target config file uses
@code{init_targets} scheme (``linear'' script is executed before @code{init} and @code{init_targets} - after),
so separating these two configuration stages is very convenient, as the easiest way to overcome this
problem is to convert board config file to use @code{init_board} procedure. Board config scripts don't
-need to override @code{init_targets} defined in target config files when they only need to to add some specifics.
+need to override @code{init_targets} defined in target config files when they only need to add some specifics.
-Just as @code{init_targets}, the @code{init_board} procedure can be overriden by ``next level'' script (which sources
+Just as @code{init_targets}, the @code{init_board} procedure can be overridden by ``next level'' script (which sources
the original), allowing greater code reuse.
@example
@example
set _TARGETNAME_1 $_CHIPNAME.cpu1
set _TARGETNAME_2 $_CHIPNAME.cpu2
-target create $_TARGETNAME_1 cortex_a8 -chain-position $_CHIPNAME.dap \
+target create $_TARGETNAME_1 cortex_a -chain-position $_CHIPNAME.dap \
-coreid 0 -dbgbase $_DAP_DBG1
-target create $_TARGETNAME_2 cortex_a8 -chain-position $_CHIPNAME.dap \
+target create $_TARGETNAME_2 cortex_a -chain-position $_CHIPNAME.dap \
-coreid 1 -dbgbase $_DAP_DBG2
#define 2 targets working in smp.
target smp $_CHIPNAME.cpu2 $_CHIPNAME.cpu1
@end example
-In the above example on cortex_a8, 2 cpus are working in SMP.
+In the above example on cortex_a, 2 cpus are working in SMP.
In SMP only one GDB instance is created and :
@itemize @bullet
@item a set of hardware breakpoint sets the same breakpoint on all targets in the list.
displayed by the GDB session @pxref{usingopenocdsmpwithgdb,,Using OpenOCD SMP with GDB}.
@end itemize
-The SMP behaviour can be disabled/enabled dynamically. On cortex_a8 following
+The SMP behaviour can be disabled/enabled dynamically. On cortex_a following
command have been implemented.
@itemize @bullet
-@item cortex_a8 smp_on : enable SMP mode, behaviour is as described above.
-@item cortex_a8 smp_off : disable SMP mode, the current target is the one
+@item cortex_a smp_on : enable SMP mode, behaviour is as described above.
+@item cortex_a smp_off : disable SMP mode, the current target is the one
displayed in the GDB session, only this target is now controlled by GDB
session. This behaviour is useful during system boot up.
-@item cortex_a8 smp_gdb : display/fix the core id displayed in GDB session see
+@item cortex_a smp_gdb : display/fix the core id displayed in GDB session see
following example.
@end itemize
@example
->cortex_a8 smp_gdb
+>cortex_a smp_gdb
gdb coreid 0 -> -1
#0 : coreid 0 is displayed to GDB ,
#-> -1 : next resume triggers a real resume
-> cortex_a8 smp_gdb 1
+> cortex_a smp_gdb 1
gdb coreid 0 -> 1
#0 :coreid 0 is displayed to GDB ,
#->1 : next resume displays coreid 1 to GDB
> resume
-> cortex_a8 smp_gdb
+> cortex_a smp_gdb
gdb coreid 1 -> 1
#1 :coreid 1 is displayed to GDB ,
#->1 : next resume displays coreid 1 to GDB
-> cortex_a8 smp_gdb -1
+> cortex_a smp_gdb -1
gdb coreid 1 -> -1
#1 :coreid 1 is displayed to GDB,
#->-1 : next resume triggers a real resume
Such a handler might write to chip registers to force a reset,
use a JRC to do that (preferable -- the target may be wedged!),
or force a watchdog timer to trigger.
-(For Cortex-M3 targets, this is not necessary. The target
+(For Cortex-M targets, this is not necessary. The target
driver knows how to use trigger an NVIC reset when SRST is
not available.)
The @code{init_boards} procedure is a similar concept concerning board config files
(@xref{theinitboardprocedure,,The init_board procedure}.)
+@anchor{theinittargeteventsprocedure}
+@subsection The init_target_events procedure
+@cindex init_target_events procedure
+
+A special procedure called @code{init_target_events} is run just after
+@code{init_targets} (@xref{theinittargetsprocedure,,The init_targets
+procedure}.) and before @code{init_board}
+(@xref{theinitboardprocedure,,The init_board procedure}.) It is used
+to set up default target events for the targets that do not have those
+events already assigned.
+
@subsection ARM Core Specific Hacks
If the chip has a DCC, enable it. If the chip is an ARM9 with some
use @option{enable} see these errors reported.
@end deffn
+@deffn {Config Command} gdb_target_description (@option{enable}|@option{disable})
+Set to @option{enable} to cause OpenOCD to send the target descriptions to gdb via qXfer:features:read packet.
+The default behaviour is @option{disable}.
+@end deffn
+
+@deffn {Command} gdb_save_tdesc
+Saves the target descripton file to the local file system.
+
+The file name is @i{target_name}.xml.
+@end deffn
+
@anchor{eventpolling}
@section Event Polling
@c chooses among list of bit configs ... only one option
@end deffn
+@deffn {Interface Driver} {cmsis-dap}
+ARM CMSIS-DAP compliant based adapter.
+
+@deffn {Config Command} {cmsis_dap_vid_pid} [vid pid]+
+The vendor ID and product ID of the CMSIS-DAP device. If not specified
+the driver will attempt to auto detect the CMSIS-DAP device.
+Currently, up to eight [@var{vid}, @var{pid}] pairs may be given, e.g.
+@example
+cmsis_dap_vid_pid 0xc251 0xf001 0x0d28 0x0204
+@end example
+@end deffn
+
+@deffn {Config Command} {cmsis_dap_serial} [serial]
+Specifies the @var{serial} of the CMSIS-DAP device to use.
+If not specified, serial numbers are not considered.
+@end deffn
+
+@deffn {Command} {cmsis-dap info}
+Display various device information, like hardware version, firmware version, current bus status.
+@end deffn
+@end deffn
+
@deffn {Interface Driver} {dummy}
A dummy software-only driver for debugging.
@end deffn
and initially asserted reset signals.
@end deffn
-@deffn {Config Command} {ftdi_layout_signal} name [@option{-data}|@option{-ndata} data_mask] [@option{-oe}|@option{-noe} oe_mask]
+@deffn {Config Command} {ftdi_layout_signal} name [@option{-data}|@option{-ndata} data_mask] [@option{-oe}|@option{-noe} oe_mask] [@option{-alias}|@option{-nalias} name]
Creates a signal with the specified @var{name}, controlled by one or more FTDI
GPIO pins via a range of possible buffer connections. The masks are FTDI GPIO
register bitmasks to tell the driver the connection and type of the output
input as necessary to provide the full set of low, high and Hi-Z
characteristics. In all other cases, the pins specified in a signal definition
are always driven by the FTDI.
+
+If @option{-alias} or @option{-nalias} is used, the signal is created
+identical (or with data inverted) to an already specified signal
+@var{name}.
@end deffn
@deffn {Command} {ftdi_set_signal} name @option{0}|@option{1}|@option{z}
@end deffn
@deffn {Interface Driver} {jlink}
-Segger J-Link family of USB adapters. It currently supports only the JTAG transport.
+Segger J-Link family of USB adapters. It currently supports JTAG and SWD transports.
@quotation Compatibility Note
Segger released many firmware versions for the many harware versions they
@deffn {Config} {jlink pid} val
Set the USB PID of the interface. As a configuration command, it can be used only before 'init'.
@end deffn
+@deffn {Config} {jlink serial} serial-number
+Set the @var{serial-number} of the interface, in case more than one adapter is connected to the host.
+If not specified, serial numbers are not considered.
+
+Note that there may be leading zeros in the @var{serial-number} string
+that will not show in the Segger software, but must be specified here.
+Debug level 3 output contains serial numbers if there is a mismatch.
+
+As a configuration command, it can be used only before 'init'.
+@end deffn
@end deffn
@deffn {Interface Driver} {parport}
that OpenOCD would normally use to access the target.
Currently supported adapters include the ST STLINK and TI ICDI.
+STLINK firmware version >= V2.J21.S4 recommended due to issues with earlier
+versions of firmware where serial number is reset after first use. Suggest
+using ST firmware update utility to upgrade STLINK firmware even if current
+version reported is V2.J21.S4.
@deffn {Config Command} {hla_device_desc} description
Currently Not Supported.
@end deffn
@deffn {Config Command} {hla_serial} serial
-Currently Not Supported.
+Specifies the serial number of the adapter.
@end deffn
@deffn {Config Command} {hla_layout} (@option{stlink}|@option{icdi})
The vendor ID and product ID of the device.
@end deffn
-@deffn {Config Command} {stlink_api} api_level
-Manually sets the stlink api used, valid options are 1 or 2. (@b{STLINK Only}).
+@deffn {Command} {hla_command} command
+Execute a custom adapter-specific command. The @var{command} string is
+passed as is to the underlying adapter layout handler.
+@end deffn
+
+@deffn {Config Command} {trace} source_clock_hz [output_file_path]
+Enable SWO tracing (if supported). The source clock rate for the
+trace port must be specified, this is typically the CPU clock rate. If
+the optional output file is specified then raw trace data is appended
+to the file, and the file is created if it does not exist.
@end deffn
@end deffn
No arguments: print status.
@end deffn
+@deffn {Interface Driver} {bcm2835gpio}
+This SoC is present in Raspberry Pi which is a cheap single-board computer
+exposing some GPIOs on its expansion header.
+
+The driver accesses memory-mapped GPIO peripheral registers directly
+for maximum performance, but the only possible race condition is for
+the pins' modes/muxing (which is highly unlikely), so it should be
+able to coexist nicely with both sysfs bitbanging and various
+peripherals' kernel drivers. The driver restores the previous
+configuration on exit.
+
+See @file{interface/raspberrypi-native.cfg} for a sample config and
+pinout.
+
+@end deffn
+
@section Transport Configuration
@cindex Transport
As noted earlier, depending on the version of OpenOCD you use,
@deffn Command {transport select} transport_name
Select which of the supported transports to use in this OpenOCD session.
The transport must be supported by the debug adapter hardware and by the
-version of OPenOCD you are using (including the adapter's driver).
+version of OpenOCD you are using (including the adapter's driver).
No arguments: returns name of session's selected transport.
@end deffn
No parameters: displays current settings.
@end deffn
+@subsection CMSIS-DAP Transport
+@cindex CMSIS-DAP
+CMSIS-DAP is an ARM-specific transport that is used to connect to
+compilant debuggers.
+
@subsection SPI Transport
@cindex SPI
@cindex Serial Peripheral Interface
TAPs serve many roles, including:
@itemize @bullet
-@item @b{Debug Target} A CPU TAP can be used as a GDB debug target
-@item @b{Flash Programing} Some chips program the flash directly via JTAG.
+@item @b{Debug Target} A CPU TAP can be used as a GDB debug target.
+@item @b{Flash Programming} Some chips program the flash directly via JTAG.
Others do it indirectly, making a CPU do it.
@item @b{Program Download} Using the same CPU support GDB uses,
you can initialize a DRAM controller, download code to DRAM, and then
start running that code.
@item @b{Boundary Scan} Most chips support boundary scan, which
helps test for board assembly problems like solder bridges
-and missing connections
+and missing connections.
@end itemize
OpenOCD must know about the active TAPs on your board(s).
@cindex scan chain
TAPs are part of a hardware @dfn{scan chain},
-which is daisy chain of TAPs.
+which is a daisy chain of TAPs.
They also need to be added to
OpenOCD's software mirror of that hardware list,
giving each member a name and associating other data with it.
OpenOCD can detect some of that information, but not all
of it. @xref{autoprobing,,Autoprobing}.
-Unfortunately those TAPs can't always be autoconfigured,
+Unfortunately, those TAPs can't always be autoconfigured,
because not all devices provide good support for that.
JTAG doesn't require supporting IDCODE instructions, and
chips with JTAG routers may not link TAPs into the chain
Board configuration files combine all the targets on a board,
and so forth.
Note that @emph{the order in which TAPs are declared is very important.}
-It must match the order in the JTAG scan chain, both inside
-a single chip and between them.
+That declaration order must match the order in the JTAG scan chain,
+both inside a single chip and between them.
@xref{faqtaporder,,FAQ TAP Order}.
For example, the ST Microsystems STR912 chip has
jtag newtap str912 bs ... params ...
@end example
-Actual config files use a variable instead of literals like
-@option{str912}, to support more than one chip of each type.
-@xref{Config File Guidelines}.
+Actual config files typically use a variable such as @code{$_CHIPNAME}
+instead of literals like @option{str912}, to support more than one chip
+of each type. @xref{Config File Guidelines}.
@deffn Command {jtag names}
Returns the names of all current TAPs in the scan chain.
name rules: start with an alphabetic character, then numbers
and underscores are OK; while others (including dots!) are not.
-@quotation Tip
-In older code, JTAG TAPs were numbered from 0..N.
-This feature is still present.
-However its use is highly discouraged, and
-should not be relied on; it will be removed by mid-2010.
-Update all of your scripts to use TAP names rather than numbers,
-by paying attention to the runtime warnings they trigger.
-Using TAP numbers in target configuration scripts prevents
-reusing those scripts on boards with multiple targets.
-@end quotation
-
@section TAP Declaration Commands
@c shouldn't this be(come) a {Config Command}?
and should follow this convention:
@itemize @bullet
-@item @code{bs} -- For boundary scan if this is a seperate TAP;
+@item @code{bs} -- For boundary scan if this is a separate TAP;
@item @code{cpu} -- The main CPU of the chip, alternatively
@code{arm} and @code{dsp} on chips with both ARM and DSP CPUs,
-@code{arm1} and @code{arm2} on chips two ARMs, and so forth;
+@code{arm1} and @code{arm2} on chips with two ARMs, and so forth;
@item @code{etb} -- For an embedded trace buffer (example: an ARM ETB11);
@item @code{flash} -- If the chip has a flash TAP, like the str912;
-@item @code{jrc} -- For JTAG route controller (example: the ICEpick modules
+@item @code{jrc} -- For JTAG route controller (example: the ICEPick modules
on many Texas Instruments chips, like the OMAP3530 on Beagleboards);
-@item @code{tap} -- Should be used only FPGA or CPLD like devices
+@item @code{tap} -- Should be used only for FPGA- or CPLD-like devices
with a single TAP;
@item @code{unknownN} -- If you have no idea what the TAP is for (N is a number);
@item @emph{when in doubt} -- Use the chip maker's name in their data sheet.
-For example, the Freescale IMX31 has a SDMA (Smart DMA) with
+For example, the Freescale i.MX31 has a SDMA (Smart DMA) with
a JTAG TAP; that TAP should be named @code{sdma}.
@end itemize
@itemize @bullet
@item @code{-disable} (or @code{-enable})
@*Use the @code{-disable} parameter to flag a TAP which is not
-linked in to the scan chain after a reset using either TRST
+linked into the scan chain after a reset using either TRST
or the JTAG state machine's @sc{reset} state.
You may use @code{-enable} to highlight the default state
(the TAP is linked in).
@xref{enablinganddisablingtaps,,Enabling and Disabling TAPs}.
-@item @code{-expected-id} @var{number}
+@item @code{-expected-id} @var{NUMBER}
@*A non-zero @var{number} represents a 32-bit IDCODE
which you expect to find when the scan chain is examined.
These codes are not required by all JTAG devices.
JTAG requires the two LSBs of this value to be 01.
By default, @code{-ircapture} and @code{-irmask} are set
up to verify that two-bit value. You may provide
-additional bits, if you know them, or indicate that
+additional bits if you know them, or indicate that
a TAP doesn't conform to the JTAG specification.
@item @code{-irmask} @var{NUMBER}
@*A mask used with @code{-ircapture}
@section Other TAP commands
-@deffn Command {jtag cget} dotted.name @option{-event} name
-@deffnx Command {jtag configure} dotted.name @option{-event} name string
+@deffn Command {jtag cget} dotted.name @option{-event} event_name
+@deffnx Command {jtag configure} dotted.name @option{-event} event_name handler
At this writing this TAP attribute
mechanism is used only for event handling.
(It is not a direct analogue of the @code{cget}/@code{configure}
by issuing the relevant JTAG commands.
@end itemize
-If you need some action after each JTAG reset, which isn't actually
+If you need some action after each JTAG reset which isn't actually
specific to any TAP (since you can't yet trust the scan chain's
contents to be accurate), you might:
In some systems, a @dfn{JTAG Route Controller} (JRC)
is used to enable and/or disable specific JTAG TAPs.
-Many ARM based chips from Texas Instruments include
-an ``ICEpick'' module, which is a JRC.
+Many ARM-based chips from Texas Instruments include
+an ``ICEPick'' module, which is a JRC.
Such chips include DaVinci and OMAP3 processors.
A given TAP may not be visible until the JRC has been
TargetName Type Endian TapName State
-- ------------------ ---------- ------ ------------------ ------------
0* at91rm9200.cpu arm920t little at91rm9200.cpu running
- 1 MyTarget cortex_m3 little mychip.foo tap-disabled
+ 1 MyTarget cortex_m little mychip.foo tap-disabled
@end verbatim
One member of that list is the @dfn{current target}, which
only relevant on boards which have more than one target.
@end deffn
-@section Target CPU Types and Variants
+@section Target CPU Types
@cindex target type
@cindex CPU type
-@cindex CPU variant
Each target has a @dfn{CPU type}, as shown in the output of
the @command{targets} command. You need to specify that type
(@pxref{Architecture and Core Commands}),
and more.
-For some CPU types, OpenOCD also defines @dfn{variants} which
-indicate differences that affect their handling.
-For example, a particular implementation bug might need to be
-worked around in some chip versions.
-
It's easy to see what target types are supported,
since there's a command to list them.
-However, there is currently no way to list what target variants
-are supported (other than by reading the OpenOCD source code).
@anchor{targettypes}
@deffn Command {target types}
Lists all supported target types.
-At this writing, the supported CPU types and variants are:
+At this writing, the supported CPU types are:
@itemize @bullet
@item @code{arm11} -- this is a generation of ARMv6 cores
@item @code{arm9tdmi} -- this is an ARMv4 core
@item @code{avr} -- implements Atmel's 8-bit AVR instruction set.
(Support for this is preliminary and incomplete.)
-@item @code{cortex_a8} -- this is an ARMv7 core with an MMU
-@item @code{cortex_m3} -- this is an ARMv7 core, supporting only the
+@item @code{cortex_a} -- this is an ARMv7 core with an MMU
+@item @code{cortex_m} -- this is an ARMv7 core, supporting only the
compact Thumb2 instruction set.
@item @code{dragonite} -- resembles arm966e
@item @code{dsp563xx} -- implements Freescale's 24-bit DSP.
(Support for this is still incomplete.)
@item @code{fa526} -- resembles arm920 (w/o Thumb)
@item @code{feroceon} -- resembles arm926
-@item @code{mips_m4k} -- a MIPS core. This supports one variant:
+@item @code{mips_m4k} -- a MIPS core
@item @code{xscale} -- this is actually an architecture,
not a CPU type. It is based on the ARMv5 architecture.
-There are several variants defined:
+@item @code{openrisc} -- this is an OpenRISC 1000 core.
+The current implementation supports three JTAG TAP cores:
@itemize @minus
-@item @code{ixp42x}, @code{ixp45x}, @code{ixp46x},
-@code{pxa27x} ... instruction register length is 7 bits
-@item @code{pxa250}, @code{pxa255},
-@code{pxa26x} ... instruction register length is 5 bits
-@item @code{pxa3xx} ... instruction register length is 11 bits
+@item @code{OpenCores TAP} (See: @emph{http://opencores.org/project,jtag})
+@item @code{Altera Virtual JTAG TAP} (See: @emph{http://www.altera.com/literature/ug/ug_virtualjtag.pdf})
+@item @code{Xilinx BSCAN_* virtual JTAG interface} (See: @emph{http://www.xilinx.com/support/documentation/sw_manuals/xilinx14_2/spartan6_hdl.pdf})
+@end itemize
+And two debug interfaces cores:
+@itemize @minus
+@item @code{Advanced debug interface} (See: @emph{http://opencores.org/project,adv_debug_sys})
+@item @code{SoC Debug Interface} (See: @emph{http://opencores.org/project,dbg_interface})
@end itemize
@end itemize
@end deffn
The key steps you use might look something like this
@example
-target create MyTarget cortex_m3 -chain-position mychip.cpu
+target create MyTarget cortex_m -chain-position mychip.cpu
$MyTarget configure -work-area-phys 0x08000 -work-area-size 8096
$MyTarget configure -event reset-deassert-pre @{ jtag_rclk 5 @}
$MyTarget configure -event reset-init @{ myboard_reinit @}
@item @var{configparams} ... all parameters accepted by
@command{$target_name configure} are permitted.
If the target is big-endian, set it here with @code{-endian big}.
-If the variant matters, set it here with @code{-variant}.
You @emph{must} set the @code{-chain-position @var{dotted.name}} here.
@end itemize
@emph{Warning:} changing some of these after setup is dangerous.
For example, moving a target from one TAP to another;
-and changing its endianness or variant.
+and changing its endianness.
@itemize @bullet
two different handlers, but calling it twice with the
same event name assigns only one handler.
-@item @code{-variant} @var{name} -- specifies a variant of the target,
-which OpenOCD needs to know about.
-
@item @code{-work-area-backup} (@option{0}|@option{1}) -- says
whether the work area gets backed up; by default,
@emph{it is not backed up.}
The value should normally correspond to a static mapping for the
@code{-work-area-phys} address, set up by the current operating system.
+@anchor{rtostype}
@item @code{-rtos} @var{rtos_type} -- enable rtos support for target,
@var{rtos_type} can be one of @option{auto}|@option{eCos}|@option{ThreadX}|
-@option{FreeRTOS}|@option{linux}|@option{ChibiOS}.
+@option{FreeRTOS}|@option{linux}|@option{ChibiOS}|@option{embKernel}
+@xref{gdbrtossupport,,RTOS Support}.
@end itemize
@end deffn
@item @b{gdb-end}
@* When the target has halted and GDB is not doing anything (see early halt)
@item @b{gdb-flash-erase-start}
-@* Before the GDB flash process tries to erase the flash
+@* Before the GDB flash process tries to erase the flash (default is
+@code{reset init})
@item @b{gdb-flash-erase-end}
@* After the GDB flash process has finished erasing the flash
@item @b{gdb-flash-write-start}
@* Before GDB writes to the flash
@item @b{gdb-flash-write-end}
-@* After GDB writes to the flash
+@* After GDB writes to the flash (default is @code{reset halt})
@item @b{gdb-start}
@* Before the target steps, gdb is trying to start/resume the target
@item @b{halted}
@deffn Command {flash write_image} [erase] [unlock] filename [offset] [type]
Write the image @file{filename} to the current target's flash bank(s).
+Only loadable sections from the image are written.
A relocation @var{offset} may be specified, in which case it is added
to the base address for each section in the image.
The file [@var{type}] can be specified
The @var{num} parameter is a value shown by @command{flash banks}.
@end deffn
+@deffn Command {flash padded_value} num value
+Sets the default value used for padding any image sections, This should
+normally match the flash bank erased value. If not specified by this
+comamnd or the flash driver then it defaults to 0xff.
+@end deffn
+
@anchor{program}
-@deffn Command {program} filename [verify] [reset] [offset]
+@deffn Command {program} filename [verify] [reset] [exit] [offset]
This is a helper script that simplifies using OpenOCD as a standalone
programmer. The only required parameter is @option{filename}, the others are optional.
@xref{Flash Programming}.
@end example
@end deffn
+@anchor{at91samd}
+@deffn {Flash Driver} at91samd
+@cindex at91samd
+
+@deffn Command {at91samd chip-erase}
+Issues a complete Flash erase via the Device Service Unit (DSU). This can be
+used to erase a chip back to its factory state and does not require the
+processor to be halted.
+@end deffn
+
+@deffn Command {at91samd set-security}
+Secures the Flash via the Set Security Bit (SSB) command. This prevents access
+to the Flash and can only be undone by using the chip-erase command which
+erases the Flash contents and turns off the security bit. Warning: at this
+time, openocd will not be able to communicate with a secured chip and it is
+therefore not possible to chip-erase it without using another tool.
+
+@example
+at91samd set-security enable
+@end example
+@end deffn
+
+@deffn Command {at91samd eeprom}
+Shows or sets the EEPROM emulation size configuration, stored in the User Row
+of the Flash. When setting, the EEPROM size must be specified in bytes and it
+must be one of the permitted sizes according to the datasheet. Settings are
+written immediately but only take effect on MCU reset. EEPROM emulation
+requires additional firmware support and the minumum EEPROM size may not be
+the same as the minimum that the hardware supports. Set the EEPROM size to 0
+in order to disable this feature.
+
+@example
+at91samd eeprom
+at91samd eeprom 1024
+@end example
+@end deffn
+
+@deffn Command {at91samd bootloader}
+Shows or sets the bootloader size configuration, stored in the User Row of the
+Flash. This is called the BOOTPROT region. When setting, the bootloader size
+must be specified in bytes and it must be one of the permitted sizes according
+to the datasheet. Settings are written immediately but only take effect on
+MCU reset. Setting the bootloader size to 0 disables bootloader protection.
+
+@example
+at91samd bootloader
+at91samd bootloader 16384
+@end example
+@end deffn
+
+@end deffn
+
@anchor{at91sam3}
@deffn {Flash Driver} at91sam3
@cindex at91sam3
@end deffn
@deffn {Flash Driver} lpc2000
-Most members of the LPC1700 and LPC2000 microcontroller families from NXP
-include internal flash and use Cortex-M3 (LPC1700) or ARM7TDMI (LPC2000) cores.
+All members of the LPC11(x)00 and LPC1300 microcontroller families and most members
+of the LPC1700, LPC1800, LPC2000 and LPC4300 microcontroller families from NXP
+include internal flash and use Cortex-M0 (LPC11(x)00), Cortex-M3 (LPC1300, LPC1700,
+LPC1800), Cortex-M4 (LPC4300) or ARM7TDMI (LPC2000) cores.
@quotation Note
There are LPC2000 devices which are not supported by the @var{lpc2000}
@item @var{variant} ... required, may be
@option{lpc2000_v1} (older LPC21xx and LPC22xx)
@option{lpc2000_v2} (LPC213x, LPC214x, LPC210[123], LPC23xx and LPC24xx)
-or @option{lpc1700} (LPC175x and LPC176x)
+@option{lpc1700} (LPC175x and LPC176x)
+@option{lpc4300} - available also as @option{lpc1800} alias (LPC18x[2357] and
+LPC43x[2357])
+@option{lpc1100} (LPC11(x)xx and LPC13xx)
+or @option{auto} - automatically detects flash variant and size for LPC11(x)00,
+LPC1300 and LPC1700
@item @var{clock_kHz} ... the frequency, in kiloHertz,
at which the core is running
@item @option{calc_checksum} ... optional (but you probably want to provide this!),
@end deffn
@deffn {Flash Driver} ocl
-@emph{No idea what this is, other than using some arm7/arm9 core.}
+This driver is an implementation of the ``on chip flash loader''
+protocol proposed by Pavel Chromy.
+
+It is a minimalistic command-response protocol intended to be used
+over a DCC when communicating with an internal or external flash
+loader running from RAM. An example implementation for AT91SAM7x is
+available in @file{contrib/loaders/flash/at91sam7x/}.
@example
flash bank $_FLASHNAME ocl 0 0 0 0 $_TARGETNAME
@end deffn
@end deffn
+@deffn {Flash Driver} psoc4
+All members of the PSoC 41xx/42xx microcontroller family from Cypress
+include internal flash and use ARM Cortex M0 cores.
+The driver automatically recognizes a number of these chips using
+the chip identification register, and autoconfigures itself.
+
+Note: Erased internal flash reads as 00.
+System ROM of PSoC 4 does not implement erase of a flash sector.
+
+@example
+flash bank $_FLASHNAME psoc4 0 0 0 0 $_TARGETNAME
+@end example
+
+psoc4-specific commands
+@deffn Command {psoc4 flash_autoerase} num (on|off)
+Enables or disables autoerase mode for a flash bank.
+
+If flash_autoerase is off, use mass_erase before flash programming.
+Flash erase command fails if region to erase is not whole flash memory.
+
+If flash_autoerase is on, a sector is both erased and programmed in one
+system ROM call. Flash erase command is ignored.
+This mode is suitable for gdb load.
+
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {psoc4 mass_erase} num
+Erases the contents of the flash memory, protection and security lock.
+
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+@end deffn
+
@deffn {Flash Driver} stellaris
All members of the Stellaris LM3Sxxx microcontroller family from
Texas Instruments
@deffn {Flash Driver} stm32lx
All members of the STM32L microcontroller families from ST Microelectronics
-include internal flash and use ARM Cortex-M3 cores.
+include internal flash and use ARM Cortex-M3 and Cortex-M0+ cores.
The driver automatically recognizes a number of these chips using
the chip identification register, and autoconfigures itself.
Note that some devices have been found that have a flash size register that contains
an invalid value, to workaround this issue you can override the probed value used by
-the flash driver.
+the flash driver. If you use 0 as the bank base address, it tells the
+driver to autodetect the bank location assuming you're configuring the
+second bank.
@example
-flash bank $_FLASHNAME stm32lx 0 0x20000 0 0 $_TARGETNAME
+flash bank $_FLASHNAME stm32lx 0x08000000 0x20000 0 0 $_TARGETNAME
@end example
+
+Some stm32lx-specific commands are defined:
+
+@deffn Command {stm32lx mass_erase} num
+Mass erases the entire stm32lx device (all flash banks and EEPROM
+data). This is the only way to unlock a protected flash (unless RDP
+Level is 2 which can't be unlocked at all).
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
@end deffn
@deffn {Flash Driver} str7x
@end example
@end deffn
+@deffn {Flash Driver} sim3x
+All members of the SiM3 microcontroller family from Silicon Laboratories
+include internal flash and use ARM Cortex M3 cores. It supports both JTAG
+and SWD interface.
+The @var{sim3x} driver tries to probe the device to auto detect the MCU.
+If this failes, it will use the @var{size} parameter as the size of flash bank.
+
+@example
+flash bank $_FLASHNAME sim3x 0 $_CPUROMSIZE 0 0 $_TARGETNAME
+@end example
+
+There are 2 commands defined in the @var{sim3x} driver:
+
+@deffn Command {sim3x mass_erase}
+Erases the complete flash. This is used to unlock the flash.
+And this command is only possible when using the SWD interface.
+@end deffn
+
+@deffn Command {sim3x lock}
+Lock the flash. To unlock use the @command{sim3x mass_erase} command.
+@end deffn
+
+@end deffn
+
@subsection str9xpec driver
@cindex str9xpec
@end deffn
+@deffn {Flash Driver} nrf51
+All members of the nRF51 microcontroller families from Nordic Semiconductor
+include internal flash and use ARM Cortex-M0 core.
+
+@example
+flash bank $_FLASHNAME nrf51 0 0x00000000 0 0 $_TARGETNAME
+@end example
+
+Some nrf51-specific commands are defined:
+
+@deffn Command {nrf51 mass_erase}
+Erases the contents of the code memory and user information
+configuration registers as well. It must be noted that this command
+works only for chips that do not have factory pre-programmed region 0
+code.
+@end deffn
+@end deffn
@section mFlash
or using the cmds given in @ref{flashprogrammingcommands,,Flash Programming Commands}.
@*To simplify using the flash cmds directly a jimtcl script is available that handles the programming and verify stage.
-OpenOCD will program/verify/reset the target and shutdown.
+OpenOCD will program/verify/reset the target and optionally shutdown.
The script is executed as follows and by default the following actions will be peformed.
@enumerate
@item @code{flash write_image} is called to erase and write any flash using the filename given.
@item @code{verify_image} is called if @option{verify} parameter is given.
@item @code{reset run} is called if @option{reset} parameter is given.
-@item OpenOCD is shutdown.
+@item OpenOCD is shutdown if @option{exit} parameter is given.
@end enumerate
An example of usage is given below. @xref{program}.
# program and verify using elf/hex/s19. verify and reset
# are optional parameters
openocd -f board/stm32f3discovery.cfg \
- -c "program filename.elf verify reset"
+ -c "program filename.elf verify reset exit"
# binary files need the flash address passing
openocd -f board/stm32f3discovery.cfg \
- -c "program filename.bin 0x08000000"
+ -c "program filename.bin exit 0x08000000"
@end example
@node NAND Flash Commands
by using @command{targets} command with the name of the
target which should become current.
-@deffn Command reg [(number|name) [value]]
+@deffn Command reg [(number|name) [(value|'force')]]
Access a single register by @var{number} or by its @var{name}.
The target must generally be halted before access to CPU core
registers is allowed. Depending on the hardware, some other
are flagged as such.
@emph{With number/name}: display that register's value.
+Use @var{force} argument to read directly from the target,
+bypassing any internal cache.
@emph{With both number/name and value}: set register's value.
Writes may be held in a writeback cache internal to OpenOCD,
@section Misc Commands
@cindex profiling
-@deffn Command {profile} seconds filename
+@deffn Command {profile} seconds filename [start end]
Profiling samples the CPU's program counter as quickly as possible,
which is useful for non-intrusive stochastic profiling.
-Saves up to 10000 sampines in @file{filename} using ``gmon.out'' format.
+Saves up to 10000 samples in @file{filename} using ``gmon.out''
+format. Optional @option{start} and @option{end} parameters allow to
+limit the address range.
@end deffn
@deffn Command {version}
@cindex Debug Access Port
@cindex DAP
These commands are specific to ARM architecture v7 Debug Access Port (DAP),
-included on Cortex-M3 and Cortex-A8 systems.
+included on Cortex-M and Cortex-A systems.
They are available in addition to other core-specific commands that may be available.
@deffn Command {dap apid} [num]
If @var{value} is defined, first assigns that.
@end deffn
-@subsection Cortex-M3 specific commands
-@cindex Cortex-M3
+@deffn Command {dap apcsw} [0 / 1]
+fix CSW_SPROT from register AP_REG_CSW on selected dap.
+Defaulting to 0.
+@end deffn
+
+@subsection Cortex-M specific commands
+@cindex Cortex-M
-@deffn Command {cortex_m3 maskisr} (@option{auto}|@option{on}|@option{off})
+@deffn Command {cortex_m maskisr} (@option{auto}|@option{on}|@option{off})
Control masking (disabling) interrupts during target step/resume.
The @option{auto} option handles interrupts during stepping a way they get
Default is @option{auto}.
@end deffn
-@deffn Command {cortex_m3 vector_catch} [@option{all}|@option{none}|list]
+@deffn Command {cortex_m vector_catch} [@option{all}|@option{none}|list]
@cindex vector_catch
Vector Catch hardware provides dedicated breakpoints
for certain hardware events.
This finishes by listing the current vector catch configuration.
@end deffn
-@deffn Command {cortex_m3 reset_config} (@option{srst}|@option{sysresetreq}|@option{vectreset})
+@deffn Command {cortex_m reset_config} (@option{srst}|@option{sysresetreq}|@option{vectreset})
Control reset handling. The default @option{srst} is to use srst if fitted,
otherwise fallback to @option{vectreset}.
@itemize @minus
@item @option{sysresetreq} use NVIC SYSRESETREQ to reset system.
@item @option{vectreset} use NVIC VECTRESET to reset system.
@end itemize
-Using @option{vectreset} is a safe option for all current Cortex-M3 cores.
+Using @option{vectreset} is a safe option for all current Cortex-M cores.
This however has the disadvantage of only resetting the core, all peripherals
are uneffected. A solution would be to use a @code{reset-init} event handler to manually reset
the peripherals.
@xref{targetevents,,Target Events}.
@end deffn
+@section Intel Architecture
+
+Intel Quark X10xx is the first product in the Quark family of SoCs. It is an IA-32
+(Pentium x86 ISA) compatible SoC. The core CPU in the X10xx is codenamed Lakemont.
+Lakemont version 1 (LMT1) is used in X10xx. The CPU TAP (Lakemont TAP) is used for
+software debug and the CLTAP is used for SoC level operations.
+Useful docs are here: https://communities.intel.com/community/makers/documentation
+@itemize
+@item Intel Quark SoC X1000 OpenOCD/GDB/Eclipse App Note (web search for doc num 330015)
+@item Intel Quark SoC X1000 Debug Operations User Guide (web search for doc num 329866)
+@item Intel Quark SoC X1000 Datasheet (web search for doc num 329676)
+@end itemize
+
+@subsection x86 32-bit specific commands
+The three main address spaces for x86 are memory, I/O and configuration space.
+These commands allow a user to read and write to the 64Kbyte I/O address space.
+
+@deffn Command {x86_32 idw} address
+Display the contents of a 32-bit I/O port from address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 idh} address
+Display the contents of a 16-bit I/O port from address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 idb} address
+Display the contents of a 8-bit I/O port from address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 iww} address
+Write the contents of a 32-bit I/O port to address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 iwh} address
+Write the contents of a 16-bit I/O port to address range 0x0000 - 0xffff.
+@end deffn
+
+@deffn Command {x86_32 iwb} address
+Write the contents of a 8-bit I/O port to address range 0x0000 - 0xffff.
+@end deffn
+
+@section OpenRISC Architecture
+
+The OpenRISC CPU is a soft core. It is used in a programmable SoC which can be
+configured with any of the TAP / Debug Unit available.
+
+@subsection TAP and Debug Unit selection commands
+@deffn Command {tap_select} (@option{vjtag}|@option{mohor}|@option{xilinx_bscan})
+Select between the Altera Virtual JTAG , Xilinx Virtual JTAG and Mohor TAP.
+@end deffn
+@deffn Command {du_select} (@option{adv}|@option{mohor}) [option]
+Select between the Advanced Debug Interface and the classic one.
+
+An option can be passed as a second argument to the debug unit.
+
+When using the Advanced Debug Interface, option = 1 means the RTL core is
+configured with ADBG_USE_HISPEED = 1. This configuration skips status checking
+between bytes while doing read or write bursts.
+@end deffn
+
+@subsection Registers commands
+@deffn Command {addreg} [name] [address] [feature] [reg_group]
+Add a new register in the cpu register list. This register will be
+included in the generated target descriptor file.
+
+@strong{[feature]} must be "org.gnu.gdb.or1k.group[0..10]".
+
+@strong{[reg_group]} can be anything. The default register list defines "system",
+ "dmmu", "immu", "dcache", "icache", "mac", "debug", "perf", "power", "pic"
+ and "timer" groups.
+
+@emph{example:}
+@example
+addreg rtest 0x1234 org.gnu.gdb.or1k.group0 system
+@end example
+
+
+@end deffn
+@deffn Command {readgroup} (@option{group})
+Display all registers in @emph{group}.
+
+@emph{group} can be "system",
+ "dmmu", "immu", "dcache", "icache", "mac", "debug", "perf", "power", "pic",
+ "timer" or any new group created with addreg command.
+@end deffn
+
@anchor{softwaredebugmessagesandtracing}
@section Software Debug Messages and Tracing
@cindex Linux-ARM DCC support
a lighter weight mechanism using only the DCC channel.
Currently @command{target_request debugmsgs}
-is supported only for @option{arm7_9} and @option{cortex_m3} cores.
+is supported only for @option{arm7_9} and @option{cortex_m} cores.
These messages are received as part of target polling, so
you need to have @command{poll on} active to receive them.
They are intrusive in that they will affect program execution
probably will not be usable with other XSVF tools.
+@node Utility Commands
+@chapter Utility Commands
+@cindex Utility Commands
+
+@section RAM testing
+@cindex RAM testing
+
+There is often a need to stress-test random access memory (RAM) for
+errors. OpenOCD comes with a Tcl implementation of well-known memory
+testing procedures allowing the detection of all sorts of issues with
+electrical wiring, defective chips, PCB layout and other common
+hardware problems.
+
+To use them, you usually need to initialise your RAM controller first;
+consult your SoC's documentation to get the recommended list of
+register operations and translate them to the corresponding
+@command{mww}/@command{mwb} commands.
+
+Load the memory testing functions with
+
+@example
+source [find tools/memtest.tcl]
+@end example
+
+to get access to the following facilities:
+
+@deffn Command {memTestDataBus} address
+Test the data bus wiring in a memory region by performing a walking
+1's test at a fixed address within that region.
+@end deffn
+
+@deffn Command {memTestAddressBus} baseaddress size
+Perform a walking 1's test on the relevant bits of the address and
+check for aliasing. This test will find single-bit address failures
+such as stuck-high, stuck-low, and shorted pins.
+@end deffn
+
+@deffn Command {memTestDevice} baseaddress size
+Test the integrity of a physical memory device by performing an
+increment/decrement test over the entire region. In the process every
+storage bit in the device is tested as zero and as one.
+@end deffn
+
+@deffn Command {runAllMemTests} baseaddress size
+Run all of the above tests over a specified memory region.
+@end deffn
+
+@section Firmware recovery helpers
+@cindex Firmware recovery
+
+OpenOCD includes an easy-to-use script to facilitate mass-market
+devices recovery with JTAG.
+
+For quickstart instructions run:
+@example
+openocd -f tools/firmware-recovery.tcl -c firmware_help
+@end example
+
@node TFTP
@chapter TFTP
@cindex TFTP
-If OpenOCD runs on an embedded host(as ZY1000 does), then TFTP can
+If OpenOCD runs on an embedded host (as ZY1000 does), then TFTP can
be used to access files on PCs (either the developer's PC or some other PC).
The way this works on the ZY1000 is to prefix a filename by
@node GDB and OpenOCD
@chapter GDB and OpenOCD
@cindex GDB
-OpenOCD complies with the remote gdbserver protocol, and as such can be used
+OpenOCD complies with the remote gdbserver protocol and, as such, can be used
to debug remote targets.
Setting up GDB to work with OpenOCD can involve several components:
With the remote protocol, GDB sessions start a little differently
than they do when you're debugging locally.
-Here's an examples showing how to start a debug session with a
+Here's an example showing how to start a debug session with a
small ARM program.
In this case the program was linked to be loaded into SRAM on a Cortex-M3.
Most programs would be written into flash (address 0) and run from there.
@example
define hook-step
-mon cortex_m3 maskisr on
+mon cortex_m maskisr on
end
define hookpost-step
-mon cortex_m3 maskisr off
+mon cortex_m maskisr off
end
@end example
that the OpenOCD option @command{gdb_breakpoint_override} is not required when
using a memory map. @xref{gdbbreakpointoverride,,gdb_breakpoint_override}.
-To view the configured memory map in GDB, use the GDB command @option{info mem}
+To view the configured memory map in GDB, use the GDB command @option{info mem}.
All other unassigned addresses within GDB are treated as RAM.
GDB 6.8 and higher set any memory area not in the memory map as inaccessible.
@end example
@end itemize
+@section RTOS Support
+@cindex RTOS Support
+@anchor{gdbrtossupport}
+
+OpenOCD includes RTOS support, this will however need enabling as it defaults to disabled.
+It can be enabled by passing @option{-rtos} arg to the target @xref{rtostype,,RTOS Type}.
+
+@* An example setup is below:
+
+@example
+$_TARGETNAME configure -rtos auto
+@end example
+
+This will attempt to auto detect the RTOS within your application.
+
+Currently supported rtos's include:
+@itemize @bullet
+@item @option{eCos}
+@item @option{ThreadX}
+@item @option{FreeRTOS}
+@item @option{linux}
+@item @option{ChibiOS}
+@item @option{embKernel}
+@end itemize
+
+@quotation Note
+Before an RTOS can be detected, it must export certain symbols; otherwise, it cannot
+be used by OpenOCD. Below is a list of the required symbols for each supported RTOS.
+@end quotation
+
+@table @code
+@item eCos symbols
+Cyg_Thread::thread_list, Cyg_Scheduler_Base::current_thread.
+@item ThreadX symbols
+_tx_thread_current_ptr, _tx_thread_created_ptr, _tx_thread_created_count.
+@item FreeRTOS symbols
+pxCurrentTCB, pxReadyTasksLists, xDelayedTaskList1, xDelayedTaskList2,
+pxDelayedTaskList, pxOverflowDelayedTaskList, xPendingReadyList,
+xTasksWaitingTermination, xSuspendedTaskList, uxCurrentNumberOfTasks, uxTopUsedPriority.
+@item linux symbols
+init_task.
+@item ChibiOS symbols
+rlist, ch_debug, chSysInit.
+@item embKernel symbols
+Rtos::sCurrentTask, Rtos::sListReady, Rtos::sListSleep,
+Rtos::sListSuspended, Rtos::sMaxPriorities, Rtos::sCurrentTaskCount.
+@end table
+
+For most RTOS supported the above symbols will be exported by default. However for
+some, eg. FreeRTOS @option{xTasksWaitingTermination} is only exported
+if @option{INCLUDE_vTaskDelete} is defined during the build.
@node Tcl Scripting API
@chapter Tcl Scripting API
@cindex Tcl scripts
@section API rules
-The commands are stateless. E.g. the telnet command line has a concept
-of currently active target, the Tcl API proc's take this sort of state
-information as an argument to each proc.
+Tcl commands are stateless; e.g. the @command{telnet} command has
+a concept of currently active target, the Tcl API proc's take this sort
+of state information as an argument to each proc.
There are three main types of return values: single value, name value
pair list and lists.
Name value pair. The proc 'foo' below returns a name/value pair
list.
-@verbatim
-
- > set foo(me) Duane
- > set foo(you) Oyvind
- > set foo(mouse) Micky
- > set foo(duck) Donald
+@example
+> set foo(me) Duane
+> set foo(you) Oyvind
+> set foo(mouse) Micky
+> set foo(duck) Donald
+@end example
If one does this:
- > set foo
+@example
+> set foo
+@end example
The result is:
- me Duane you Oyvind mouse Micky duck Donald
+@example
+me Duane you Oyvind mouse Micky duck Donald
+@end example
Thus, to get the names of the associative array is easy:
- foreach { name value } [set foo] {
- puts "Name: $name, Value: $value"
- }
+@verbatim
+foreach { name value } [set foo] {
+ puts "Name: $name, Value: $value"
+}
@end verbatim
-Lists returned must be relatively small. Otherwise a range
+Lists returned should be relatively small. Otherwise, a range
should be passed in to the proc in question.
@section Internal low-level Commands
-By low-level, the intent is a human would not directly use these commands.
+By "low-level," we mean commands that a human would typically not
+invoke directly.
-Low-level commands are (should be) prefixed with "ocd_", e.g.
+Some low-level commands need to be prefixed with "ocd_"; e.g.
@command{ocd_flash_banks}
-is the low level API upon which @command{flash banks} is implemented.
+is the low-level API upon which @command{flash banks} is implemented.
@itemize @bullet
@item @b{mem2array} <@var{varname}> <@var{width}> <@var{addr}> <@var{nelems}>
@item @b{ocd_flash_banks} <@var{driver}> <@var{base}> <@var{size}> <@var{chip_width}> <@var{bus_width}> <@var{target}> [@option{driver options} ...]
Return information about the flash banks
+
+@item @b{capture} <@var{command}>
+
+Run <@var{command}> and return full log output that was produced during
+its execution. Example:
+
+@example
+> capture "reset init"
+@end example
+
@end itemize
OpenOCD commands can consist of two words, e.g. "flash banks". The
@item @b{cygwin} Running under Cygwin
@item @b{darwin} Darwin (Mac-OS) is the underlying operating sytem.
@item @b{freebsd} Running under FreeBSD
+@item @b{openbsd} Running under OpenBSD
+@item @b{netbsd} Running under NetBSD
@item @b{linux} Linux is the underlying operating sytem
@item @b{mingw32} Running under MingW32
@item @b{winxx} Built using Microsoft Visual Studio
+@item @b{ecos} Running under eCos
@item @b{other} Unknown, none of the above.
@end itemize
is jim, not real tcl).
@end quotation
+@section Tcl RPC server
+@cindex RPC
+
+OpenOCD provides a simple RPC server that allows to run arbitrary Tcl
+commands and receive the results.
+
+To access it, your application needs to connect to a configured TCP port
+(see @command{tcl_port}). Then it can pass any string to the
+interpreter terminating it with @code{0x1a} and wait for the return
+value (it will be terminated with @code{0x1a} as well). This can be
+repeated as many times as desired without reopening the connection.
+
+Remember that most of the OpenOCD commands need to be prefixed with
+@code{ocd_} to get the results back. Sometimes you might also need the
+@command{capture} command.
+
+See @file{contrib/rpc_examples/} for specific client implementations.
+
@node FAQ
@chapter FAQ
@cindex faq
Code Review / openocd.git / blobdiff