target: remove unused event definitions

[openocd.git] / doc / openocd.texi

diff --git a/doc/openocd.texi b/doc/openocd.texi
index ac491b144cb28a767e808e9fbb33b3e159388743..ebd03c4cb2b02b181d9cee5cb5fc1d65b941b8f3 100644 (file)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -2948,8 +2948,8 @@ Specifies the serial number of the adapter.
 Specifies the adapter layout to use.
 @end deffn
 
-@deffn {Config Command} {hla_vid_pid} vid pid
-The vendor ID and product ID of the device.
+@deffn {Config Command} {hla_vid_pid} [vid pid]+
+Pairs of vendor IDs and product IDs of the device.
 @end deffn
 
 @deffn {Command} {hla_command} command
@@ -4503,12 +4503,6 @@ and (if the target is using it) after SRST has been
 released on the scan chain.
 @item @b{reset-end}
 @* Issued as the final step in @command{reset} processing.
-@ignore
-@item @b{reset-halt-post}
-@* Currently not used
-@item @b{reset-halt-pre}
-@* Currently not used
-@end ignore
 @item @b{reset-init}
 @* Used by @b{reset init} command for board-specific initialization.
 This event fires after @emph{reset-deassert-post}.
@@ -4525,12 +4519,6 @@ before @command{reset_init} is called.
 This is the most robust place to use @command{jtag_rclk}
 or @command{adapter_khz} to switch to a low JTAG clock rate,
 when reset disables PLLs needed to use a fast clock.
-@ignore
-@item @b{reset-wait-pos}
-@* Currently not used
-@item @b{reset-wait-pre}
-@* Currently not used
-@end ignore
 @item @b{resume-start}
 @* Before any target is resumed
 @item @b{resume-end}
@@ -5888,9 +5876,6 @@ All members of the Stellaris LM3Sxxx, LM4x and Tiva C microcontroller
 families from Texas Instruments include internal flash. The driver
 automatically recognizes a number of these chips using the chip
 identification register, and autoconfigures itself.
-@footnote{Currently there is a @command{stellaris mass_erase} command.
-That seems pointless since the same effect can be had using the
-standard @command{flash erase_address} command.}
 
 @example
 flash bank $_FLASHNAME stellaris 0 0 0 0 $_TARGETNAME
@@ -5936,11 +5921,7 @@ as per the following example.
 flash bank $_FLASHNAME stm32f1x 0x08080000 0 0 0 $_TARGETNAME
 @end example
 
-Some stm32f1x-specific commands
-@footnote{Currently there is a @command{stm32f1x mass_erase} command.
-That seems pointless since the same effect can be had using the
-standard @command{flash erase_address} command.}
-are defined:
+Some stm32f1x-specific commands are defined:
 
 @deffn Command {stm32f1x lock} num
 Locks the entire stm32 device.
@@ -5953,8 +5934,7 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 
 @deffn Command {stm32f1x mass_erase} num
-Mass erases the entire stm32f1x device. This is the only way to
-unlock a protected flash (unless RDP Level is 2 which can't be unlocked at all).
+Mass erases the entire stm32f1x device.
 The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 
@@ -6001,8 +5981,7 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 
 @deffn Command {stm32f2x mass_erase} num
-Mass erases the entire stm32f2x device. This is the only way to
-unlock a protected flash (unless RDP Level is 2 which can't be unlocked at all).
+Mass erases the entire stm32f2x device.
 The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 
@@ -6056,8 +6035,7 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 
 @deffn Command {stm32h7x mass_erase} num
-Mass erases the entire stm32h7x device. This is the only way to
-unlock a protected flash (unless RDP Level is 2 which can't be unlocked at all).
+Mass erases the entire stm32h7x device.
 The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 @end deffn
@@ -6084,6 +6062,16 @@ flash bank $_FLASHNAME stm32lx 0x08000000 0x20000 0 0 $_TARGETNAME
 
 Some stm32lx-specific commands are defined:
 
+@deffn Command {stm32lx lock} num
+Locks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
+@deffn Command {stm32lx unlock} num
+Unlocks the entire stm32 device.
+The @var{num} parameter is a value shown by @command{flash banks}.
+@end deffn
+
 @deffn Command {stm32lx mass_erase} num
 Mass erases the entire stm32lx device (all flash banks and EEPROM
 data). This is the only way to unlock a protected flash (unless RDP
@@ -6123,8 +6111,7 @@ The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 
 @deffn Command {stm32l4x mass_erase} num
-Mass erases the entire stm32l4x device. This is the only way to
-unlock a protected flash (unless RDP Level is 2 which can't be unlocked at all).
+Mass erases the entire stm32l4x device.
 The @var{num} parameter is a value shown by @command{flash banks}.
 @end deffn
 @end deffn