Remove whitespace that occurs after '('.

[openocd.git] / src / ecosboard.c

diff --git a/src/ecosboard.c b/src/ecosboard.c
index d49abbd1594a1bb2b6009b7236ee06a04edf8b05..91780a98b9f310ac8fa2522823baf6c1d75fcb86 100644 (file)
--- a/src/ecosboard.c
+++ b/src/ecosboard.c
@@ -93,7 +93,7 @@ struct tftpd_fileops fileops =
        (int (*)(const char *, int))open,
        close,
        (int (*)(int, const void *, int))write,
-       ( int (*)(int, void *, int))read
+       (int (*)(int, void *, int))read
 };
 
 #endif
@@ -148,7 +148,6 @@ void start_profile(void)
 }
 #endif
 
-extern int eth0_up;
 static FILE *log;
 
 static char reboot_stack[2048];
@@ -254,7 +253,7 @@ void copyfile(char *name2, char *name1);
 void copydir(char *name, char *destdir);
 
 #if 0
-MTAB_ENTRY( romfs_mte1,
+MTAB_ENTRY(romfs_mte1,
                "/rom",
                "romfs",
                "",
@@ -305,7 +304,7 @@ void format(void)
        err = cyg_io_get_config(handle, CYG_IO_GET_CONFIG_FLASH_ERASE, &e, &len);
        if (err != ENOERR)
        {
-               diag_printf("Flash erase error %d offset 0x%p\n", err, e.err_address);
+               diag_printf("Flash erase error %d offset 0x%08x\n", err, e.err_address);
                reboot();
        }
 
@@ -976,13 +975,13 @@ int main(int argc, char *argv[])
        }
 
        mkdir(zylin_config_dir, 0777);
-       char *dirname=alloc_printf("%s/target", zylin_config_dir);
+       char *dirname = alloc_printf("%s/target", zylin_config_dir);
        mkdir(dirname, 0777);
        free(dirname);
-       dirname=alloc_printf("%s/board", zylin_config_dir);
+       dirname = alloc_printf("%s/board", zylin_config_dir);
        mkdir(dirname, 0777);
        free(dirname);
-       dirname=alloc_printf("%s/event", zylin_config_dir);
+       dirname = alloc_printf("%s/event", zylin_config_dir);
        mkdir(dirname, 0777);
        free(dirname);
 
@@ -1037,7 +1036,7 @@ int main(int argc, char *argv[])
        if (logAllToSerial)
        {
                diag_printf(
-                                "%s/logserial=1 => sending log output to serial port using \"debug_level 3\" as default.\n", zylin_config_dir);
+                                "%s/logserial = 1 => sending log output to serial port using \"debug_level 3\" as default.\n", zylin_config_dir);
                command_run_line(cmd_ctx, "debug_level 3");
        }
 
@@ -1131,7 +1130,7 @@ static int tftpfs_fo_lseek(struct CYG_FILE_TAG *fp, off_t *apos, int whence);
 // For simplicity we use _FILESYSTEM synchronization for all accesses since
 // we should never block in any filesystem operations.
 #if 1
-FSTAB_ENTRY( tftpfs_fste, "tftpfs", 0,
+FSTAB_ENTRY(tftpfs_fste, "tftpfs", 0,
                CYG_SYNCMODE_NONE,
                tftpfs_mount,
                tftpfs_umount,
@@ -1152,7 +1151,7 @@ FSTAB_ENTRY( tftpfs_fste, "tftpfs", 0,
 // mtab entry.
 // This defines a single ROMFS loaded into ROM at the configured address
 //
-// MTAB_ENTRY( rom_mte,        // structure name
+// MTAB_ENTRY(rom_mte, // structure name
 //             "/rom",         // mount point
 //             "romfs",        // FIlesystem type
 //             "",             // hardware device
@@ -1460,8 +1459,8 @@ static int logfs_fo_close(struct CYG_FILE_TAG *fp);
 // This defines the entry in the filesystem table.
 // For simplicity we use _FILESYSTEM synchronization for all accesses since
 // we should never block in any filesystem operations.
-FSTAB_ENTRY( logfs_fste, "logfs", 0,
-               CYG_SYNCMODE_FILE_FILESYSTEM|CYG_SYNCMODE_IO_FILESYSTEM,
+FSTAB_ENTRY(logfs_fste, "logfs", 0,
+               CYG_SYNCMODE_FILE_FILESYSTEM | CYG_SYNCMODE_IO_FILESYSTEM,
                logfs_mount,
                logfs_umount,
                logfs_open,