* GNU General Public License for more details. *
* *
* You should have received a copy of the GNU General Public License *
- * along with this program; if not, write to the *
- * Free Software Foundation, Inc., *
- * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. *
+ * along with this program. If not, see <http://www.gnu.org/licenses/>. *
***************************************************************************/
#ifdef HAVE_CONFIG_H
* read/write data to the SLC controller.
* - DMA descriptors will be put at start of working area,
* - Hardware generated ECC will be stored at ECC_OFFS
- * - OOB wil be read/written from/to SPARE_OFFS
+ * - OOB will be read/written from/to SPARE_OFFS
* - Actual page data will be read from/to DATA_OFFS
* There are unused holes between the used areas.
*/
}
/* after reset set other registers of SLC,
- * so reset calling is here at the begining
+ * so reset calling is here at the beginning
*/
retval = lpc32xx_reset(nand);
if (ERROR_OK != retval)
WIDTH = bus_width)
*/
retval = target_write_u32(target, 0x20020014,
- 0x3e | (bus_width == 16) ? 1 : 0);
+ 0x3e | ((bus_width == 16) ? 1 : 0));
if (ERROR_OK != retval) {
LOG_ERROR("could not set SLC_CFG");
return ERROR_NAND_OPERATION_FAILED;
* 2. Copy generated ECC data from Register to Spare Area
* 3. X'fer next 256 bytes of data from Memory to Flash.
* 4. Copy generated ECC data from Register to Spare Area.
- * 5. X'fer 16 byets of Spare area from Memory to Flash.
+ * 5. X'fer 16 bytes of Spare area from Memory to Flash.
* Read Operation Sequence for Small Block NAND
* ----------------------------------------------------------
* 1. X'fer 256 bytes of data from Flash to Memory.
* 5. X'fer 16 bytes of Spare area from Flash to Memory.
* Write Operation Sequence for Large Block NAND
* ----------------------------------------------------------
- * 1. Steps(1-4) of Write Operations repeate for four times
+ * 1. Steps(1-4) of Write Operations repeated for four times
* which generates 16 DMA descriptors to X'fer 2048 bytes of
* data & 32 bytes of ECC data.
* 2. X'fer 64 bytes of Spare area from Memory to Flash.
* Read Operation Sequence for Large Block NAND
* ----------------------------------------------------------
- * 1. Steps(1-4) of Read Operations repeate for four times
+ * 1. Steps(1-4) of Read Operations repeated for four times
* which generates 16 DMA descriptors to X'fer 2048 bytes of
* data & 32 bytes of ECC data.
* 2. X'fer 64 bytes of Spare area from Flash to Memory.
* 2. Copy generated ECC data from Register to Spare Area
* 3. X'fer next 256 bytes of data from Memory to Flash.
* 4. Copy generated ECC data from Register to Spare Area.
- * 5. X'fer 16 byets of Spare area from Memory to Flash.
+ * 5. X'fer 16 bytes of Spare area from Memory to Flash.
* Read Operation Sequence for Small Block NAND
* ----------------------------------------------------------
* 1. X'fer 256 bytes of data from Flash to Memory.
* 5. X'fer 16 bytes of Spare area from Flash to Memory.
* Write Operation Sequence for Large Block NAND
* ----------------------------------------------------------
- * 1. Steps(1-4) of Write Operations repeate for four times
+ * 1. Steps(1-4) of Write Operations repeated for four times
* which generates 16 DMA descriptors to X'fer 2048 bytes of
* data & 32 bytes of ECC data.
* 2. X'fer 64 bytes of Spare area from Memory to Flash.
* Read Operation Sequence for Large Block NAND
* ----------------------------------------------------------
- * 1. Steps(1-4) of Read Operations repeate for four times
+ * 1. Steps(1-4) of Read Operations repeated for four times
* which generates 16 DMA descriptors to X'fer 2048 bytes of
* data & 32 bytes of ECC data.
* 2. X'fer 64 bytes of Spare area from Flash to Memory.
target_mem_base = pworking_area->address;
/*
- * Skip writting page which has all 0xFF data as this will
+ * Skip writing page which has all 0xFF data as this will
* generate 0x0 value.
*/
if (data && !oob) {
return retval;
}
- /* Write first decriptor to DMA controller */
+ /* Write first descriptor to DMA controller */
retval = target_write_memory(target, 0x31000100, 4,
sizeof(dmac_ll_t) / 4,
(uint8_t *)dmalist);
return retval;
}
- /* Write OOB decriptor to DMA controller */
+ /* Write OOB descriptor to DMA controller */
retval = target_write_memory(target, 0x31000100, 4,
sizeof(dmac_ll_t) / 4,
(uint8_t *)(&dmalist[nll-1]));
return retval;
}
- /* Write first decriptor to DMA controller */
+ /* Write first descriptor to DMA controller */
retval = target_write_memory(target, 0x31000100, 4,
sizeof(dmac_ll_t) / 4, (uint8_t *)dmalist);
if (ERROR_OK != retval) {
COMMAND_PARSE_NUMBER(uint, CMD_ARGV[0], num);
struct nand_device *nand = get_nand_device_by_num(num);
if (!nand) {
- command_print(CMD_CTX, "nand device '#%s' is out of bounds",
+ command_print(CMD, "nand device '#%s' is out of bounds",
CMD_ARGV[0]);
return ERROR_OK;
}
return ERROR_COMMAND_SYNTAX_ERROR;
}
- command_print(CMD_CTX, "%s controller selected",
+ command_print(CMD, "%s controller selected",
selected[lpc32xx_info->selected_controller]);
return ERROR_OK;