#define F_HAS_TZ BIT(2)
/* this flag indicates if the device has the same flash registers as STM32L5 */
#define F_HAS_L5_FLASH_REGS BIT(3)
+/* this flag indicates that programming should be done in quad-word
+ * the default programming word size is double-word */
+#define F_QUAD_WORD_PROG BIT(4)
/* end of STM32L4 flags ******************************************************/
bool dual_bank_mode;
int hole_sectors;
uint32_t user_bank_size;
+ uint32_t data_width;
uint32_t cr_bker_mask;
uint32_t sr_bsy_mask;
uint32_t wrpxxr_mask;
};
/* human readable list of families this drivers supports (sorted alphabetically) */
-static const char *device_families = "STM32G0/G4/L4/L4+/L5/WB/WL";
+static const char *device_families = "STM32G0/G4/L4/L4+/L5/U5/WB/WL";
static const struct stm32l4_rev stm32_415_revs[] = {
{ 0x1000, "1" }, { 0x1001, "2" }, { 0x1003, "3" }, { 0x1007, "4" }
{ 0x1000, "A" },
};
+static const struct stm32l4_rev stm32_482_revs[] = {
+ { 0x1000, "A" }, { 0x1001, "Z" }, { 0x1003, "Y" }, { 0x2000, "B" },
+};
+
static const struct stm32l4_rev stm32_495_revs[] = {
{ 0x2001, "2.1" },
};
.otp_base = 0x1FFF7000,
.otp_size = 1024,
},
+ {
+ .id = 0x482,
+ .revs = stm32_482_revs,
+ .num_revs = ARRAY_SIZE(stm32_482_revs),
+ .device_str = "STM32U57/U58xx",
+ .max_flash_size_kb = 2048,
+ .flags = F_HAS_DUAL_BANK | F_QUAD_WORD_PROG | F_HAS_TZ | F_HAS_L5_FLASH_REGS,
+ .flash_regs_base = 0x40022000,
+ .fsize_addr = 0x0BFA07A0,
+ .otp_base = 0x0BFA0000,
+ .otp_size = 512,
+ },
{
.id = 0x495,
.revs = stm32_495_revs,
return ERROR_FAIL; /* Checkme: What better error to use?*/
bank->driver_priv = stm32l4_info;
- /* The flash write must be aligned to a double word (8-bytes) boundary.
- * Ask the flash infrastructure to ensure required alignment */
- bank->write_start_alignment = bank->write_end_alignment = 8;
-
stm32l4_info->probed = false;
stm32l4_info->otp_enabled = false;
stm32l4_info->user_bank_size = bank->size;
return stm32l4_write_all_wrpxy(bank, wrpxy, n_wrp);
}
-/* Count is in double-words */
+/* count is the size divided by stm32l4_info->data_width */
static int stm32l4_write_block(struct flash_bank *bank, const uint8_t *buffer,
uint32_t offset, uint32_t count)
{
struct target *target = bank->target;
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
uint32_t buffer_size;
struct working_area *write_algorithm;
struct working_area *source;
return retval;
}
- /* memory buffer, size *must* be multiple of dword plus one dword for rp and one for wp */
+ /* memory buffer, size *must* be multiple of stm32l4_info->data_width
+ * plus one dword for rp and one for wp */
+ /* FIXME, currently only STM32U5 devices do have a different data_width,
+ * but STM32U5 device flash programming does not go through this function
+ * so temporarily continue to consider the default data_width = 8 */
buffer_size = target_get_working_area_avail(target) & ~(2 * sizeof(uint32_t) - 1);
if (buffer_size < 256) {
LOG_WARNING("large enough working area not available, can't do block memory writes");
buf_set_u32(reg_params[4].value, 0, 32, stm32l4_get_flash_reg_by_index(bank, STM32_FLASH_SR_INDEX));
buf_set_u32(reg_params[5].value, 0, 32, stm32l4_get_flash_reg_by_index(bank, STM32_FLASH_CR_INDEX));
- retval = target_run_flash_async_algorithm(target, buffer, count, 8,
+ retval = target_run_flash_async_algorithm(target, buffer, count, stm32l4_info->data_width,
0, NULL,
ARRAY_SIZE(reg_params), reg_params,
source->address, source->size,
return retval;
}
-/* Count is in double-words */
+/* count is the size divided by stm32l4_info->data_width */
static int stm32l4_write_block_without_loader(struct flash_bank *bank, const uint8_t *buffer,
uint32_t offset, uint32_t count)
{
+ struct stm32l4_flash_bank *stm32l4_info = bank->driver_priv;
struct target *target = bank->target;
uint32_t address = bank->base + offset;
int retval = ERROR_OK;
/* write directly to flash memory */
const uint8_t *src = buffer;
+ const uint32_t data_width_in_words = stm32l4_info->data_width / 4;
while (count--) {
- retval = target_write_memory(target, address, 4, 2, src);
+ retval = target_write_memory(target, address, 4, data_width_in_words, src);
if (retval != ERROR_OK)
return retval;
if (retval != ERROR_OK)
return retval;
- src += 8;
- address += 8;
+ src += stm32l4_info->data_width;
+ address += stm32l4_info->data_width;
}
/* reset PG in FLASH_CR */
return ERROR_TARGET_NOT_HALTED;
}
- /* The flash write must be aligned to a double word (8-bytes) boundary.
+ /* ensure that stm32l4_info->data_width is 'at least' a multiple of dword */
+ assert(stm32l4_info->data_width % 8 == 0);
+
+ /* The flash write must be aligned to the 'stm32l4_info->data_width' boundary.
* The flash infrastructure ensures it, do just a security check */
- assert(offset % 8 == 0);
- assert(count % 8 == 0);
+ assert(offset % stm32l4_info->data_width == 0);
+ assert(count % stm32l4_info->data_width == 0);
/* STM32G4xxx Cat. 3 devices may have gaps between banks, check whether
* data to be written does not go into a gap:
if ((stm32l4_info->part_info->id == 0x467) && stm32l4_info->dual_bank_mode) {
LOG_INFO("Couldn't use the flash loader in dual-bank mode");
use_flashloader = false;
+ } else if (stm32l4_info->part_info->id == 0x482) {
+ /**
+ * FIXME the current flashloader does not support writing in quad-words
+ * which is required for STM32U5 devices.
+ */
+ use_flashloader = false;
}
if (use_flashloader) {
if (stm32l4_info->tzen && (stm32l4_info->rdp == RDP_LEVEL_0_5))
LOG_INFO("RDP level is 0.5, the work-area should reside in non-secure RAM");
- retval = stm32l4_write_block(bank, buffer, offset, count / 8);
+ retval = stm32l4_write_block(bank, buffer, offset,
+ count / stm32l4_info->data_width);
}
if (!use_flashloader || retval == ERROR_TARGET_RESOURCE_NOT_AVAILABLE) {
LOG_INFO("falling back to single memory accesses");
- retval = stm32l4_write_block_without_loader(bank, buffer, offset, count / 8);
+ retval = stm32l4_write_block_without_loader(bank, buffer, offset,
+ count / stm32l4_info->data_width);
}
-
err_lock:
retval2 = stm32l4_write_flash_reg_by_index(bank, stm32l4_get_flash_cr_with_lock_index(bank), FLASH_LOCK);
stm32l4_info->idcode, part_info->device_str, rev_str, rev_id);
stm32l4_info->flash_regs_base = stm32l4_info->part_info->flash_regs_base;
+ stm32l4_info->data_width = (part_info->flags & F_QUAD_WORD_PROG) ? 16 : 8;
stm32l4_info->cr_bker_mask = FLASH_BKER;
stm32l4_info->sr_bsy_mask = FLASH_BSY;
+ /* Set flash write alignment boundaries.
+ * Ask the flash infrastructure to ensure required alignment */
+ bank->write_start_alignment = bank->write_end_alignment = stm32l4_info->data_width;
+
/* initialise the flash registers layout */
if (part_info->flags & F_HAS_L5_FLASH_REGS)
stm32l4_info->flash_regs = stm32l5_ns_flash_regs;
stm32l4_info->bank1_sectors = num_pages / 2;
}
break;
+ case 0x482: /* STM32U57/U58xx */
+ /* if flash size is max (2M) the device is always dual bank
+ * otherwise check DUALBANK bit(21)
+ */
+ page_size_kb = 8;
+ num_pages = flash_size_kb / page_size_kb;
+ stm32l4_info->bank1_sectors = num_pages;
+ if ((flash_size_kb == part_info->max_flash_size_kb) || (stm32l4_info->optr & BIT(21))) {
+ stm32l4_info->dual_bank_mode = true;
+ stm32l4_info->bank1_sectors = num_pages / 2;
+ }
+ break;
case 0x495: /* STM32WB5x */
case 0x496: /* STM32WB3x */
/* single bank flash */
Code Review / openocd.git / blobdiff