-/*
- * This represents the bits which must be sent out on TMS/SWDIO to
- * switch a DAP implemented using an SWJ-DP module into SWD mode.
- * These bits are stored (and transmitted) LSB-first.
- *
- * See the DAP-Lite specification, section 2.2.5 for information
- * about making the debug link select SWD or JTAG. (Similar info
- * is in a few other ARM documents.)
- */
-static const uint8_t jtag2swd_bitseq[] = {
- /* More than 50 TCK/SWCLK cycles with TMS/SWDIO high,
- * putting both JTAG and SWD logic into reset state.
- */
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
- /* Switching sequence enables SWD and disables JTAG
- * NOTE: bits in the DP's IDCODE may expose the need for
- * an old/obsolete/deprecated sequence (0xb6 0xed).
- */
- 0x9e, 0xe7,
- /* More than 50 TCK/SWCLK cycles with TMS/SWDIO high,
- * putting both JTAG and SWD logic into reset state.
- */
- 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff,
-};
-
-/**
- * Put the debug link into SWD mode, if the target supports it.
- * The link's initial mode may be either JTAG (for example,
- * with SWJ-DP after reset) or SWD.
- *
- * @param target Enters SWD mode (if possible).
- *
- * Note that targets using the JTAG-DP do not support SWD, and that
- * some targets which could otherwise support it may have have been
- * configured to disable SWD signaling
- *
- * @return ERROR_OK or else a fault code.
- */
-int dap_to_swd(struct target *target)
-{
- struct arm *arm = target_to_arm(target);
- int retval;
-
- if (!arm->dap) {
- LOG_ERROR("SWD mode is not available");
- return ERROR_FAIL;
- }
-
- LOG_DEBUG("Enter SWD mode");
-
- /* REVISIT it's ugly to need to make calls to a "jtag"
- * subsystem if the link may not be in JTAG mode...
- */
-
- retval = jtag_add_tms_seq(8 * sizeof(jtag2swd_bitseq),
- jtag2swd_bitseq, TAP_INVALID);
- if (retval == ERROR_OK)
- retval = jtag_execute_queue();
-
- /* set up the DAP's ops vector for SWD mode. */
- arm->dap->ops = &swd_dap_ops;
-
- return retval;
-}
-
-COMMAND_HANDLER(handle_swd_wcr)
-{
- int retval;
- struct target *target = get_current_target(CMD_CTX);
- struct arm *arm = target_to_arm(target);
- struct adiv5_dap *dap = arm->dap;
- uint32_t wcr;
- unsigned trn, scale = 0;
-
- switch (CMD_ARGC) {
- /* no-args: just dump state */
- case 0:
- /*retval = swd_queue_dp_read(dap, DP_WCR, &wcr); */
- retval = dap_queue_dp_read(dap, DP_WCR, &wcr);
- if (retval == ERROR_OK)
- dap->ops->run(dap);
- if (retval != ERROR_OK) {
- LOG_ERROR("can't read WCR?");
- return retval;
- }
-
- command_print(CMD_CTX,
- "turnaround=%" PRIu32 ", prescale=%" PRIu32,
- WCR_TO_TRN(wcr),
- WCR_TO_PRESCALE(wcr));
- return ERROR_OK;
-
- case 2: /* TRN and prescale */
- COMMAND_PARSE_NUMBER(uint, CMD_ARGV[1], scale);
- if (scale > 7) {
- LOG_ERROR("prescale %d is too big", scale);
- return ERROR_FAIL;
- }
- /* FALL THROUGH */
-
- case 1: /* TRN only */
- COMMAND_PARSE_NUMBER(uint, CMD_ARGV[0], trn);
- if (trn < 1 || trn > 4) {
- LOG_ERROR("turnaround %d is invalid", trn);
- return ERROR_FAIL;
- }
-
- wcr = ((trn - 1) << 8) | scale;
- /* FIXME
- * write WCR ...
- * then, re-init adapter with new TRN
- */
- LOG_ERROR("can't yet modify WCR");
- return ERROR_FAIL;
-
- default: /* too many arguments */
- return ERROR_COMMAND_SYNTAX_ERROR;
- }
-}
-