- jtag_khz/speed are now single parameter only. These are used
[openocd.git] / src / target / cortex_m3.c
index 803f05ce89c5e7746881cb54e53ab035f266091e..e3ed4cfbb81dcbaf0875246844241b99b6364b41 100644 (file)
@@ -81,6 +81,7 @@ target_type_t cortexm3_target =
        .write_memory = cortex_m3_write_memory,
        .bulk_write_memory = cortex_m3_bulk_write_memory,
        .checksum_memory = armv7m_checksum_memory,
+       .blank_check_memory = armv7m_blank_check_memory,
        
        .run_algorithm = armv7m_run_algorithm,
        
@@ -673,6 +674,7 @@ int cortex_m3_assert_reset(target_t *target)
        armv7m_common_t *armv7m = target->arch_info;
        cortex_m3_common_t *cortex_m3 = armv7m->arch_info;
        swjdp_common_t *swjdp = &cortex_m3->swjdp_info;
+       int assert_srst = 1;
        
        LOG_DEBUG("target->state: %s", target_state_strings[target->state]);
        
@@ -689,7 +691,7 @@ int cortex_m3_assert_reset(target_t *target)
                
        ahbap_write_system_u32(swjdp, DCB_DCRDR, 0 );
        
-       if (target->reset_mode == RESET_RUN)
+       if (!target->reset_halt)
        {
                /* Set/Clear C_MASKINTS in a separate operation */
                if (cortex_m3->dcb_dhcsr & C_MASKINTS)
@@ -706,13 +708,53 @@ int cortex_m3_assert_reset(target_t *target)
                ahbap_write_system_atomic_u32(swjdp, DCB_DEMCR, TRCENA | VC_HARDERR | VC_BUSERR | VC_CORERESET );
        }
        
-       if (jtag_reset_config & RESET_SRST_PULLS_TRST)
+       /* following hack is to handle luminary reset
+        * when srst is asserted the luminary device seesm to also clear the debug registers
+        * which does not match the armv7 debug TRM */
+               
+       if (strcmp(cortex_m3->variant, "lm3s") == 0)
+       {
+               /* get revision of lm3s target, only early silicon has this issue
+                * Fury Rev B, DustDevil Rev B, Tempest all ok */
+               
+               u32 did0;
+               
+               if (target_read_u32(target, 0x400fe000, &did0) == ERROR_OK)
+               {
+                       switch ((did0 >> 16) & 0xff)
+                       {
+                               case 0:
+                                       /* all Sandstorm suffer issue */
+                                       assert_srst = 0;
+                                       break;
+                               
+                               case 1:
+                               case 3:
+                                       /* only Fury/DustDevil rev A suffer reset problems */
+                                       if (((did0 >> 8) & 0xff) == 0)
+                                               assert_srst = 0;
+                                       break;
+                       }
+               }
+       }
+       
+       if (assert_srst)
        {
-               jtag_add_reset(1, 1);
+               /* default to asserting srst */
+               if (jtag_reset_config & RESET_SRST_PULLS_TRST)
+               {
+                       jtag_add_reset(1, 1);
+               }
+               else
+               {
+                       jtag_add_reset(0, 1);
+               }
        }
        else
        {
-               jtag_add_reset(0, 1);
+               /* this causes the luminary device to reset using the watchdog */
+               ahbap_write_system_atomic_u32(swjdp, NVIC_AIRCR, AIRCR_VECTKEY | AIRCR_SYSRESETREQ );
+               LOG_DEBUG("Using Luminary Reset: SYSRESETREQ");
        }
        
        target->state = TARGET_RESET;
@@ -1325,7 +1367,6 @@ int cortex_m3_examine(struct command_context_s *cmd_ctx, struct target_s *target
        return ERROR_OK;
 }
 
-
 int cortex_m3_quit()
 {
        
@@ -1438,6 +1479,15 @@ int cortex_m3_init_arch_info(target_t *target, cortex_m3_common_t *cortex_m3, in
        armv7m->pre_restore_context = NULL;
        armv7m->post_restore_context = NULL;
        
+       if (variant)
+       {
+               cortex_m3->variant = strdup(variant);
+       }
+       else
+       {
+               cortex_m3->variant = strdup("");
+       }
+       
        armv7m_init_arch_info(target, armv7m);  
        armv7m->arch_info = cortex_m3;
        armv7m->load_core_reg_u32 = cortex_m3_load_core_reg_u32;
@@ -1468,7 +1518,6 @@ int cortex_m3_target_command(struct command_context_s *cmd_ctx, char *cmd, char
                variant = args[4];
        
        cortex_m3_init_arch_info(target, cortex_m3, chain_pos, variant);
-       cortex_m3_register_commands(cmd_ctx);
        
        return ERROR_OK;
 }
@@ -1481,4 +1530,3 @@ int cortex_m3_register_commands(struct command_context_s *cmd_ctx)
        
        return retval;
 }
-

Linking to existing account procedure

If you already have an account and want to add another login method you MUST first sign in with your existing account and then change URL to read https://review.openocd.org/login/?link to get to this page again but this time it'll work for linking. Thank you.

SSH host keys fingerprints

1024 SHA256:YKx8b7u5ZWdcbp7/4AeXNaqElP49m6QrwfXaqQGJAOk gerrit-code-review@openocd.zylin.com (DSA)
384 SHA256:jHIbSQa4REvwCFG4cq5LBlBLxmxSqelQPem/EXIrxjk gerrit-code-review@openocd.org (ECDSA)
521 SHA256:UAOPYkU9Fjtcao0Ul/Rrlnj/OsQvt+pgdYSZ4jOYdgs gerrit-code-review@openocd.org (ECDSA)
256 SHA256:A13M5QlnozFOvTllybRZH6vm7iSt0XLxbA48yfc2yfY gerrit-code-review@openocd.org (ECDSA)
256 SHA256:spYMBqEYoAOtK7yZBrcwE8ZpYt6b68Cfh9yEVetvbXg gerrit-code-review@openocd.org (ED25519)
+--[ED25519 256]--+
|=..              |
|+o..   .         |
|*.o   . .        |
|+B . . .         |
|Bo. = o S        |
|Oo.+ + =         |
|oB=.* = . o      |
| =+=.+   + E     |
|. .=o   . o      |
+----[SHA256]-----+
2048 SHA256:0Onrb7/PHjpo6iVZ7xQX2riKN83FJ3KGU0TvI0TaFG4 gerrit-code-review@openocd.zylin.com (RSA)