tcl/board: frdm kinetis boards have SRST connected

[openocd.git] / tcl / board / zy1000.cfg

diff --git a/tcl/board/zy1000.cfg b/tcl/board/zy1000.cfg
index d8bb46502f74c2186d68bfe731228c97f61a35fd..57deaa8375f327aebfab1f321d1c5e5040e613fe 100644 (file)
--- a/tcl/board/zy1000.cfg
+++ b/tcl/board/zy1000.cfg
@@ -10,36 +10,38 @@
 reset_config srst_only srst_pulls_trst
 
 
-if { [info exists CHIPNAME] } {        
-   set  _CHIPNAME $CHIPNAME    
-} else {        
+if { [info exists CHIPNAME] } {
+   set  _CHIPNAME $CHIPNAME
+} else {
    set  _CHIPNAME zy1000
 }
 
-if { [info exists ENDIAN] } {  
-   set  _ENDIAN $ENDIAN    
-} else {        
+if { [info exists ENDIAN] } {
+   set  _ENDIAN $ENDIAN
+} else {
    set  _ENDIAN little
 }
 
- 
+
 #jtag scan chain
-if { [info exists CPUTAPID ] } {
+if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
    set _CPUTAPID 0x1f0f0f0f
 }
 jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi-s_r4
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME
 
 # at CPU CLK <32kHz this must be disabled
 arm7_9 fast_memory_access enable
 arm7_9 dcc_downloads enable
 
-flash bank ecosflash 0x01000000 0x200000 2 2 0 ecos/at91eb40a.elf
-$_TARGETNAME configure -event reset-init { 
+set _FLASHNAME $_CHIPNAME.flash
+flash bank $_FLASHNAME cfi 0x01000000 0x200000 2 2 $_TARGETNAME
+
+$_TARGETNAME configure -event reset-init {
        # Set up chip selects & timings
        mww 0xFFE00000 0x0100273D
        mww 0xFFE00004 0x08002125
@@ -51,21 +53,26 @@ $_TARGETNAME configure -event reset-init {
        mww 0xFFE0001c 0x70000000
        mww 0xFFE00020 0x00000001
        mww 0xFFE00024 0x00000000
-       
-       # remap  
-       mww 0xFFFFF124 0xFFFFFFFF  
+
+       # remap
+       mww 0xFFFFF124 0xFFFFFFFF
        mww 0xffff0010 0x100
        mww 0xffff0034 0x100
-       
+
        #disable 16x5x UART interrupts
        mww 0x08020004 0
 }
 
+$_TARGETNAME configure -event gdb-attach {
+       # Without this gdb-attach will first time as probe will fail
+       reset init
+}
+
 # required for usable performance. Used for lots of
 # other things than flash programming.
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00020000 -work-area-size 0x20000 -work-area-backup 0
 
-jtag_khz 16000
+adapter_khz 16000
 
 
 proc production_info {} {
@@ -75,14 +82,14 @@ proc production_info {} {
 # There is no return value from this procedure. If it is
 # successful it does not throw an exception
 #
-# Progress messages are output via puts 
+# Progress messages are output via puts
 proc production {firmwarefile serialnumber} {
        if {[string length $serialnumber]!=12} {
-               puts "Invalid serial number"
+               echo "Invalid serial number"
                return
        }
 
-       puts "Power cycling target"
+       echo "Power cycling target"
        power off
        sleep 3000
        power on
@@ -92,11 +99,11 @@ proc production {firmwarefile serialnumber} {
        verify_image $firmwarefile 0x1000000 bin
 
        # Big endian... weee!!!!
-       puts "Setting MAC number to $serialnumber"      
+       echo "Setting MAC number to $serialnumber"
        flash fillw [expr 0x1030000-0x8] "0x[string range $serialnumber 2 3][string range $serialnumber 0 1]0000" 1
        flash fillw [expr 0x1030000-0x4] "0x[string range $serialnumber 10 11][string range $serialnumber 8 9][string range $serialnumber 6 7][string range $serialnumber 4 5]" 1
-       puts "Production successful"
-} 
+       echo "Production successful"
+}
 
 
 proc production_test {} {