target: rename cortex_a8 to cortex_a

[openocd.git] / tcl / target / amdm37x.cfg

diff --git a/tcl/target/amdm37x.cfg b/tcl/target/amdm37x.cfg
index ab1868159503709ba2992d7c3f7a7af4e98c8ce7..ab2ccab176b8c6791a0cc1e18333a63d64ca7bf6 100644 (file)
--- a/tcl/target/amdm37x.cfg
+++ b/tcl/target/amdm37x.cfg
@@ -1,6 +1,6 @@
 #
-# Copyright (C)   2010        by Karl Kurbjun
-# Copyright (C)   2009, 2010  by Øyvind Harboe
+# Copyright (C)   2010-2011   by Karl Kurbjun
+# Copyright (C)   2009-2011   by Øyvind Harboe
 # Copyright (C)   2009        by David Brownell
 # Copyright (C)   2009        by Magnus Lundin
 #
@@ -21,19 +21,19 @@
 if { [info exists CHIPTYPE] } {
 
    if { [info exists CHIPNAME] } {
-      set  _CHIPNAME $CHIPNAME
+      set _CHIPNAME $CHIPNAME
    } else {
-      set  _CHIPNAME $CHIPTYPE
+      set _CHIPNAME $CHIPTYPE
    }
 
    switch $CHIPTYPE {
       dm37x {
          # Primary TAP: ICEpick-C (JTAG route controller) and boundary scan
-         set _JRC_TAPID 0x0b89102f
+         set _JRC_TAPID "-expected-id 0x2b89102f -expected-id 0x1b89102f -expected-id 0x0b89102f"
       }
       am35x {
          # Primary TAP: ICEpick-C (JTAG route controller) and boundary scan
-         set _JRC_TAPID 0x0b7ae02f
+         set _JRC_TAPID "-expected-id 0x0b7ae02f"
       }
       default {
          error "ERROR: CHIPTYPE was set, but it was not set to a valid value.  Acceptable values are \"dm37x\" or \"am35x\"."
@@ -113,9 +113,8 @@ jtag configure $_CHIPNAME.d2d -event tap-enable \
    "icepick_c_tapenable $_CHIPNAME.jrc 0"
 
 # Primary TAP: ICEpick - it is closest to TDI so last in the chain
-jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f \
-   -expected-id $_JRC_TAPID
-       
+eval "jtag newtap $_CHIPNAME jrc -irlen 6 -ircapture 0x1 -irmask 0x3f $_JRC_TAPID"
+
 ######
 # End of Chain Description
 ######
@@ -142,7 +141,7 @@ jtag configure $_CHIPNAME.jrc -event setup "jtag tapenable $_CHIPNAME.dap"
 
 # Create the CPU target to be used with GDB:  Cortex-A8, using DAP
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_a8 -chain-position $_CHIPNAME.dap
+target create $_TARGETNAME cortex_a -chain-position $_CHIPNAME.dap
 
 # The DM37x has 64K of SRAM starting at address 0x4020_0000.  Allow the first
 # 16K to be used as a scratchpad for OpenOCD.
@@ -154,30 +153,39 @@ $_TARGETNAME configure -work-area-phys 0x40200000 -work-area-size 0x4000
 ######
 
 # Set the JTAG clock down to 10 kHz to be sure that it will work with the
-#  slowest possible core clock (16.8MHz/2 = 8.4MHz). It is OK to speed up 
+#  slowest possible core clock (16.8MHz/2 = 8.4MHz). It is OK to speed up
 #  *after* PLL and clock tree setup.
 
 $_TARGETNAME configure -event "reset-start" { adapter_khz 10 }
 
-# Reset needs to be performed in in software.
-# The AM/DM37x TRM (sprugn4b) describes the software reset in detail.
-# PRM_RSTCTRL is described in table 3-425 on page 618.  We assert RST_GS
-# (bit 1 (in 31:0) ) to do a warm reset.
-
-# Create a vaiable for the register address
-set PRM_RSTCTRL 0x48307250
+# Describe the reset assert process for openocd - this is asserted with the
+# ICEPick
+$_TARGETNAME configure -event "reset-assert" {
 
-# Describe the reset assert process: A value of 2 must be written 
-# (assert bit 1) to the physical address of PRM_RSTCTRL.
+   global _CHIPNAME
 
-$_TARGETNAME configure -event \
-   reset-assert "$_TARGETNAME mww phys $PRM_RSTCTRL 2"
+   # assert warm system reset through ICEPick
+   icepick_c_wreset $_CHIPNAME.jrc
+}
 
 # After the reset is asserted we need to re-initialize debugging and speed up
 # the JTAG clock.
 
-$_TARGETNAME configure -event \
-   reset-assert-post "amdm37x_dbginit $_TARGETNAME; adapter_khz 1000"
+$_TARGETNAME configure -event reset-assert-post {
+
+   global _TARGETNAME
+   amdm37x_dbginit $_TARGETNAME
+   adapter_khz 1000
+}
+
+$_TARGETNAME configure -event gdb-attach {
+
+   global _TARGETNAME
+   amdm37x_dbginit $_TARGETNAME
+
+   echo "Halting target"
+   halt
+}
 
 ######
 # End Target Reset Event Setup:
@@ -192,9 +200,9 @@ $_TARGETNAME configure -event \
 # reset sequence.
 proc amdm37x_dbginit {target} {
    # General Cortex A8 debug initialisation
-   cortex_a8 dbginit
-   
-   # Enable DBGEN signal.  This signal is described in the ARM v7 TRM, but 
+   cortex_a dbginit
+
+   # Enable DBGEN signal.  This signal is described in the ARM v7 TRM, but
    # access to the signal appears to be implementation specific.  TI does not
    # describe this register much except a quick line that states DBGEM (sic) is
    # at this address and this bit.