tcl: Add default hooks for STM32F3x

[openocd.git] / tcl / target / stm32f3x.cfg

diff --git a/tcl/target/stm32f3x.cfg b/tcl/target/stm32f3x.cfg
index 0b3b7255f25829f415140c69cb973bdd3958566d..7ddf7d0435ad4036cdcb4693c600eb2e279f6cc3 100644 (file)
--- a/tcl/target/stm32f3x.cfg
+++ b/tcl/target/stm32f3x.cfg
@@ -4,6 +4,7 @@
 # stm32 devices support both JTAG and SWD transports.
 #
 source [find target/swj-dp.tcl]
+source [find mem_helper.tcl]
 
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
@@ -11,11 +12,7 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f3x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 16kB
@@ -56,14 +53,24 @@ swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPU
 if { [info exists BSTAPID] } {
    set _BSTAPID $BSTAPID
 } else {
-  # STM Document RM0316 rev 2 Section 30.6.2 says 0x06432041
-  # but STM32F303VCT6 rev Y has 0x06422041
+  # STM Document RM0316 rev 5 for STM32F302/303 B/C size
   set _BSTAPID1 0x06422041
+  # STM Document RM0313 rev 3 for STM32F37x
   set _BSTAPID2 0x06432041
+  #  STM Document RM364 rev 1 for STM32F334
+  set _BSTAPID3 0x06438041
+  #  STM Document RM316 rev 5 for STM32F303 6/8 size
+  #  STM Document RM365 rev 3 for STM32F302 6/8 size
+  #  STM Document RM366 rev 2 for STM32F301 6/8 size
+  set _BSTAPID4 0x06439041
+  #  STM Document RM016 rev 5 for STM32F303 D/E size
+  set _BSTAPID5 0x06446041
 }
 
 if {[using_jtag]} {
- swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 -expected-id $_BSTAPID2
+ swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
+ -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
+ -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
@@ -74,8 +81,40 @@ $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f1x 0 0 0 0 $_TARGETNAME
 
+reset_config srst_nogate
+
 if {![using_hla]} {
    # if srst is not fitted use SYSRESETREQ to
    # perform a soft reset
    cortex_m reset_config sysresetreq
 }
+
+proc stm32f3x_default_reset_start {} {
+       # Reset clock is HSI (8 MHz)
+       adapter_khz 1000
+}
+
+proc stm32f3x_default_examine_end {} {
+       # Enable debug during low power modes (uses more power)
+       mmw 0xe0042004 0x00000007 0 ;# DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
+
+       # Stop watchdog counters during halt
+       mww 0xe0042008 0x00001800 ;# DBGMCU_APB1_FZ = DBG_IWDG_STOP | DBG_WWDG_STOP
+}
+
+proc stm32f3x_default_reset_init {} {
+       # Configure PLL to boost clock to HSI x 8 (64 MHz)
+       mww 0x40021004 0x00380400 ;# RCC_CFGR = PLLMUL[3:1] | PPRE1[2]
+       mwh 0x40021002 0x0100     ;# RCC_CR[31:16] = PLLON
+       mww 0x40022000 0x00000012 ;# FLASH_ACR = PRFTBE | LATENCY[1]
+       sleep 10                  ;# Wait for PLL to lock
+       mww 0x40021004 0x00380402 ;# RCC_CFGR |= SW[1]
+
+       # Boost JTAG frequency
+       adapter_khz 8000
+}
+
+# Default hooks
+$_TARGETNAME configure -event examine-end { stm32f3x_default_examine_end }
+$_TARGETNAME configure -event reset-start { stm32f3x_default_reset_start }
+$_TARGETNAME configure -event reset-init { stm32f3x_default_reset_init }