target: restructure dap support

[openocd.git] / tcl / target / stm32f4x.cfg

diff --git a/tcl/target/stm32f4x.cfg b/tcl/target/stm32f4x.cfg
index 9aadf627ac0ed234fb2943a39e1ddf7d7b702628..73b1dc8eda447150ff6c29ae0076f05060363b96 100644 (file)
--- a/tcl/target/stm32f4x.cfg
+++ b/tcl/target/stm32f4x.cfg
@@ -15,11 +15,11 @@ if { [info exists CHIPNAME] } {
 set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
-# By default use 64kB
+# By default use 32kB (Available RAM in smallest device STM32F410)
 if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE $WORKAREASIZE
 } else {
-   set _WORKAREASIZE 0x10000
+   set _WORKAREASIZE 0x8000
 }
 
 #jtag scan chain
@@ -36,34 +36,14 @@ if { [info exists CPUTAPID] } {
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-if { [info exists BSTAPID] } {
-   set _BSTAPID $BSTAPID
-} else {
-  # See STM Document RM0090
-  # Section 38.6.2
-  # STM32F405xx/07xx and STM32F415xx/17xx
-  set _BSTAPID1 0x06413041
-  # STM32F42xxx and STM32F43xxx
-  set _BSTAPID2 0x06419041
-  # See STM Document RM0368 (Rev. 3)
-  # STM32F401B/C
-  set _BSTAPID3 0x06423041
-  # STM32F401D/E
-  set _BSTAPID4 0x06433041
-  # See STM Document RM0383 (Rev 2)
-  # STM32F411
-  set _BSTAPID5 0x06431041
-}
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
 
 if {[using_jtag]} {
- swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-     -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
-     -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
+   jtag newtap $_CHIPNAME bs -irlen 5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
+target create $_TARGETNAME cortex_m -endian $_ENDIAN -dap $_CHIPNAME.dap
 
 $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE -work-area-backup 0
 
@@ -92,6 +72,7 @@ if {![using_hla]} {
 }
 
 $_TARGETNAME configure -event examine-end {
+       # Enable debug during low power modes (uses more power)
        # DBGMCU_CR |= DBG_STANDBY | DBG_STOP | DBG_SLEEP
        mmw 0xE0042004 0x00000007 0
 
@@ -106,3 +87,21 @@ $_TARGETNAME configure -event trace-config {
        # assignment
        mmw 0xE0042004 0x00000020 0
 }
+
+$_TARGETNAME configure -event reset-init {
+       # Configure PLL to boost clock to HSI x 4 (64 MHz)
+       mww 0x40023804 0x08012008   ;# RCC_PLLCFGR 16 Mhz /8 (M) * 128 (N) /4(P)
+       mww 0x40023C00 0x00000102   ;# FLASH_ACR = PRFTBE | 2(Latency)
+       mmw 0x40023800 0x01000000 0 ;# RCC_CR |= PLLON
+       sleep 10                    ;# Wait for PLL to lock
+       mmw 0x40023808 0x00001000 0 ;# RCC_CFGR |= RCC_CFGR_PPRE1_DIV2
+       mmw 0x40023808 0x00000002 0 ;# RCC_CFGR |= RCC_CFGR_SW_PLL
+
+       # Boost JTAG frequency
+       adapter_khz 8000
+}
+
+$_TARGETNAME configure -event reset-start {
+       # Reduce speed since CPU speed will slow down to 16MHz with the reset
+       adapter_khz 2000
+}