target/stm32xx: Endian is not configurable.

[openocd.git] / tcl / target / stm32f4x.cfg

diff --git a/tcl/target/stm32f4x.cfg b/tcl/target/stm32f4x.cfg
index eafa1226865fe313f5bfb6d88fa7e0341a530ea4..faa6a7e595f0fd65dd5f10fd4d77dc2f80f3e820 100644 (file)
--- a/tcl/target/stm32f4x.cfg
+++ b/tcl/target/stm32f4x.cfg
@@ -11,11 +11,7 @@ if { [info exists CHIPNAME] } {
    set _CHIPNAME stm32f4x
 }
 
-if { [info exists ENDIAN] } {
-   set _ENDIAN $ENDIAN
-} else {
-   set _ENDIAN little
-}
+set _ENDIAN little
 
 # Work-area is a space in RAM used for flash programming
 # By default use 64kB
@@ -25,26 +21,17 @@ if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE 0x10000
 }
 
-# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
-#
-# Since we may be running of an RC oscilator, we crank down the speed a
-# bit more to be on the safe side. Perhaps superstition, but if are
-# running off a crystal, we can run closer to the limit. Note
-# that there can be a pretty wide band where things are more or less stable.
-adapter_khz 1000
-
-adapter_nsrst_delay 100
-if {$using_jtag} {
- jtag_ntrst_delay 100
-}
-
 #jtag scan chain
 if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
 } else {
-  # See STM Document RM0090
-  # Section 38.6.3 - corresponds to Cortex-M4 r0p1
-   set _CPUTAPID 0x4ba00477
+   if { [using_jtag] } {
+      # See STM Document RM0090
+      # Section 38.6.3 - corresponds to Cortex-M4 r0p1
+      set _CPUTAPID 0x4ba00477
+   } {
+      set _CPUTAPID 0x2ba01477
+   }
 }
 
 swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
@@ -58,11 +45,20 @@ if { [info exists BSTAPID] } {
   set _BSTAPID1 0x06413041
   # STM32F42xxx and STM32F43xxx
   set _BSTAPID2 0x06419041
+  # See STM Document RM0368 (Rev. 3)
+  # STM32F401B/C
+  set _BSTAPID3 0x06423041
+  # STM32F401D/E
+  set _BSTAPID4 0x06433041
+  # See STM Document RM0383 (Rev 2)
+  # STM32F411
+  set _BSTAPID5 0x06431041
 }
 
-if {$using_jtag} {
- jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
-       -expected-id $_BSTAPID2
+if {[using_jtag]} {
+ swj_newdap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
+     -expected-id $_BSTAPID2 -expected-id $_BSTAPID3 \
+     -expected-id $_BSTAPID4 -expected-id $_BSTAPID5
 }
 
 set _TARGETNAME $_CHIPNAME.cpu
@@ -73,6 +69,21 @@ $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
 
-# if srst is not fitted use SYSRESETREQ to
-# perform a soft reset
-cortex_m reset_config sysresetreq
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 16MHz, so use F_JTAG = 2MHz
+#
+# Since we may be running of an RC oscilator, we crank down the speed a
+# bit more to be on the safe side. Perhaps superstition, but if are
+# running off a crystal, we can run closer to the limit. Note
+# that there can be a pretty wide band where things are more or less stable.
+adapter_khz 2000
+
+adapter_nsrst_delay 100
+if {[using_jtag]} {
+ jtag_ntrst_delay 100
+}
+
+if {![using_hla]} {
+   # if srst is not fitted use SYSRESETREQ to
+   # perform a soft reset
+   cortex_m reset_config sysresetreq
+}