bcm281xx: Add bcm281xx SoC and bcm28155_ap board

[openocd.git] / tcl / target / stm32f4x.cfg

diff --git a/tcl/target/stm32f4x.cfg b/tcl/target/stm32f4x.cfg
index b5ab200481b0543c3a5cace4a6bb55cec65cc544..feca77c7bf77960bc93d9ccbe1fafb8995ea5997 100644 (file)
--- a/tcl/target/stm32f4x.cfg
+++ b/tcl/target/stm32f4x.cfg
@@ -1,5 +1,10 @@
 # script for stm32f4x family
 
+#
+# stm32 devices support both JTAG and SWD transports.
+#
+source [find target/swj-dp.tcl]
+
 if { [info exists CHIPNAME] } {
    set _CHIPNAME $CHIPNAME
 } else {
@@ -20,17 +25,6 @@ if { [info exists WORKAREASIZE] } {
    set _WORKAREASIZE 0x10000
 }
 
-# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
-#
-# Since we may be running of an RC oscilator, we crank down the speed a
-# bit more to be on the safe side. Perhaps superstition, but if are
-# running off a crystal, we can run closer to the limit. Note
-# that there can be a pretty wide band where things are more or less stable.
-adapter_khz 1000
-
-adapter_nsrst_delay 100
-jtag_ntrst_delay 100
-
 #jtag scan chain
 if { [info exists CPUTAPID] } {
    set _CPUTAPID $CPUTAPID
@@ -39,7 +33,8 @@ if { [info exists CPUTAPID] } {
   # Section 38.6.3 - corresponds to Cortex-M4 r0p1
    set _CPUTAPID 0x4ba00477
 }
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
+
+swj_newdap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
 
 if { [info exists BSTAPID] } {
    set _BSTAPID $BSTAPID
@@ -51,8 +46,11 @@ if { [info exists BSTAPID] } {
   # STM32F42xxx and STM32F43xxx
   set _BSTAPID2 0x06419041
 }
-jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
+
+if {$using_jtag} {
+ jtag newtap $_CHIPNAME bs -irlen 5 -expected-id $_BSTAPID1 \
        -expected-id $_BSTAPID2
+}
 
 set _TARGETNAME $_CHIPNAME.cpu
 target create $_TARGETNAME cortex_m -endian $_ENDIAN -chain-position $_TARGETNAME
@@ -62,6 +60,19 @@ $_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size $_WORKAREASIZE
 set _FLASHNAME $_CHIPNAME.flash
 flash bank $_FLASHNAME stm32f2x 0 0 0 0 $_TARGETNAME
 
+# JTAG speed should be <= F_CPU/6. F_CPU after reset is 8MHz, so use F_JTAG = 1MHz
+#
+# Since we may be running of an RC oscilator, we crank down the speed a
+# bit more to be on the safe side. Perhaps superstition, but if are
+# running off a crystal, we can run closer to the limit. Note
+# that there can be a pretty wide band where things are more or less stable.
+adapter_khz 1000
+
+adapter_nsrst_delay 100
+if {$using_jtag} {
+ jtag_ntrst_delay 100
+}
+
 # if srst is not fitted use SYSRESETREQ to
 # perform a soft reset
 cortex_m reset_config sysresetreq