X-Git-Url: https://review.openocd.org/gitweb?p=openocd.git;a=blobdiff_plain;f=README;h=34dac0b1b583be41927768178a669c436f7b3b9b;hp=985e39a9826cb588adfb96c16c03a2e22f69f0ad;hb=d796f5929c3b2baafae4b8bf27d2b1b71c49ee53;hpb=2d5f2ede55150235352773a976166c3ab68297bc

diff --git a/README b/README
index 985e39a982..34dac0b1b5 100644
--- a/README
+++ b/README
@@ -42,7 +42,7 @@ e.g.:
   openocd -f interface/ftdi/jtagkey2.cfg -c "transport select jtag" \
           -f target/ti_calypso.cfg
 
-  openocd -f interface/stlink-v2-1.cfg -c "transport select hla_swd" \
+  openocd -f interface/stlink.cfg -c "transport select hla_swd" \
           -f target/stm32l0.cfg
 
 After OpenOCD startup, connect GDB with
@@ -101,33 +101,40 @@ Supported hardware
 JTAG adapters
 -------------
 
-AICE, ARM-JTAG-EW, ARM-USB-OCD, ARM-USB-TINY, AT91RM9200, axm0432,
-BCM2835, Bus Blaster, Buspirate, Chameleon, CMSIS-DAP, Cortino, DENX,
-Digilent JTAG-SMT2, DLC 5, DLP-USB1232H, embedded projects, eStick,
-FlashLINK, FlossJTAG, Flyswatter, Flyswatter2, Gateworks, Hoegl, ICDI,
-ICEBear, J-Link, JTAG VPI, JTAGkey, JTAGkey2, JTAG-lock-pick, KT-Link,
-Lisa/L, LPC1768-Stick, MiniModule, NGX, NXHX, OOCDLink, Opendous,
-OpenJTAG, Openmoko, OpenRD, OSBDM, Presto, Redbee, RLink, SheevaPlug
-devkit, Stellaris evkits, ST-LINK (SWO tracing supported),
-STM32-PerformanceStick, STR9-comStick, sysfsgpio, TUMPA, Turtelizer,
-ULINK, USB-A9260, USB-Blaster, USB-JTAG, USBprog, VPACLink, VSLLink,
-Wiggler, XDS100v2, Xverve.
+AICE, ARM-JTAG-EW, ARM-USB-OCD, ARM-USB-TINY, AT91RM9200, axm0432, BCM2835,
+Bus Blaster, Buspirate, Cadence DPI, Chameleon, CMSIS-DAP, Cortino,
+Cypress KitProg, DENX, Digilent JTAG-SMT2, DLC 5, DLP-USB1232H,
+embedded projects, eStick, FlashLINK, FlossJTAG, Flyswatter, Flyswatter2,
+FTDI FT232R, Gateworks, Hoegl, ICDI, ICEBear, J-Link, JTAG VPI, JTAGkey,
+JTAGkey2, JTAG-lock-pick, KT-Link, Linux GPIOD, Lisa/L, LPC1768-Stick,
+Mellanox rshim, MiniModule, NGX, Nuvoton Nu-Link, Nu-Link2, NXHX, NXP IMX GPIO,
+OOCDLink, Opendous, OpenJTAG, Openmoko, OpenRD, OSBDM, Presto, Redbee,
+Remote Bitbang, RLink, SheevaPlug devkit, Stellaris evkits,
+ST-LINK (SWO tracing supported), STM32-PerformanceStick, STR9-comStick,
+sysfsgpio, TI XDS110, TUMPA, Turtelizer, ULINK, USB-A9260, USB-Blaster,
+USB-JTAG, USBprog, VPACLink, VSLLink, Wiggler, XDS100v2, Xilinx XVC/PCIe,
+Xverve.
 
 Debug targets
 -------------
 
-ARM11, ARM7, ARM9, AVR32, Cortex-A, Cortex-R, Cortex-M, LS102x-SAP,
-Feroceon/Dragonite, DSP563xx, DSP5680xx, FA526, MIPS EJTAG, NDS32,
-XScale, Intel Quark.
+ARM: AArch64, ARM11, ARM7, ARM9, Cortex-A/R (v7-A/R), Cortex-M (ARMv{6/7/8}-M),
+FA526, Feroceon/Dragonite, XScale.
+ARCv2, AVR32, DSP563xx, DSP5680xx, EnSilica eSi-RISC, EJTAG (MIPS32, MIPS64),
+Intel Quark, LS102x-SAP, NDS32, RISC-V, ST STM8.
 
 Flash drivers
 -------------
 
-ADUC702x, AT91SAM, ATH79, AVR, CFI, DSP5680xx, EFM32, EM357, FM3, FM4, Kinetis,
-LPC8xx/LPC1xxx/LPC2xxx/LPC541xx, LPC2900, LPCSPIFI, Marvell QSPI,
-Milandr, NIIET, NuMicro, PIC32mx, PSoC4, PSoC5LP, SiM3x, Stellaris, STM32,
-STMSMI, STR7x, STR9x, nRF51; NAND controllers of AT91SAM9, LPC3180, LPC32xx,
-i.MX31, MXC, NUC910, Orion/Kirkwood, S3C24xx, S3C6400, XMC1xxx, XMC4xxx.
+ADUC702x, AT91SAM, AT91SAM9 (NAND), ATH79, ATmega128RFA1, Atmel SAM, AVR, CFI,
+DSP5680xx, EFM32, EM357, eSi-RISC, eSi-TSMC, EZR32HG, FM3, FM4, Freedom E SPI,
+i.MX31, Kinetis, LPC8xx/LPC1xxx/LPC2xxx/LPC541xx, LPC2900, LPC3180, LPC32xx,
+LPCSPIFI, Marvell QSPI, MAX32, Milandr, MXC, NIIET, nRF51, nRF52 , NuMicro,
+NUC910, Orion/Kirkwood, PIC32mx, PSoC4/5LP/6, Renesas RPC HF and SH QSPI,
+S3C24xx, S3C6400, SiM3x, SiFive Freedom E, Stellaris, ST BlueNRG, STM32,
+STM32 QUAD/OCTO-SPI for Flash/FRAM/EEPROM, STMSMI, STR7x, STR9x, SWM050,
+TI CC13xx, TI CC26xx, TI CC32xx, TI MSP432, Winner Micro w600, Xilinx XCF,
+XMC1xxx, XMC4xxx.
 
 
 ==================
@@ -213,12 +220,11 @@ You'll also need:
 
 Additionally, for building from git:
 
-- autoconf >= 2.64
+- autoconf >= 2.69
 - automake >= 1.14
-- texinfo
+- texinfo >= 5.0
 
-USB-based adapters depend on libusb-1.0 and some older drivers require
-libusb-0.1 or libusb-compat-0.1. A compatible implementation, such as
+USB-based adapters depend on libusb-1.0. A compatible implementation, such as
 FreeBSD's, additionally needs the corresponding .pc files.
 
 USB-Blaster, ASIX Presto and OpenJTAG interface adapter
@@ -276,18 +282,22 @@ e.g. for cross-building for Windows 32-bit with MinGW on Debian:
 To make pkg-config work nicely for cross-compiling, you might need an
 additional wrapper script as described at
 
-  http://www.flameeyes.eu/autotools-mythbuster/pkgconfig/cross-compiling.html
+  https://autotools.io/pkgconfig/cross-compiling.html
 
 This is needed to tell pkg-config where to look for the target
 libraries that OpenOCD depends on. Alternatively, you can specify
 *_CFLAGS and *_LIBS environment variables directly, see "./configure
 --help" for the details.
 
+For a more or less complete script that does all this for you, see
+
+  contrib/cross-build.sh
+
 Parallel Port Dongles
 ---------------------
 
 If you want to access the parallel port using the PPDEV interface you
-have to specify both --enable-parport AND --enable-parport-ppdev, since the
+have to specify both --enable-parport AND --enable-parport-ppdev, since
 the later option is an option to the parport driver.
 
 The same is true for the --enable-parport-giveio option, you have to